Advertisement
AWC:
Auto
White
Balance
Control
(AWC)
mode
is
selected. Pressing the Auto White Balance Control
Button (AWC SET) (5), the white balance can be set
automatically while aiming the camera at a white
object such as white paper or white wall etc.
Note :
it is recommended to use the MANU position in the
following condition,
Under low illumination
Under colored illumination
- Under fluorescent lamp
No white object is available
. AGC Selection Button (AGC)
This button is used to select the gain of video amplifier
as follows. (See page 8 for Direct Mode and page 9 for
Setup Menu}
OFF :
The automatic gain control (AGC) is disabled and
the gain of video amplifier is set to the fixed value.
LOW :
The video gain increases approximately +6 dB.
MID :
The video gain increases approximately +9 dB.
HI:
The video gain increases approximately +12 dB.
. Auto White Balance Control Button {AWC SET)
The white balance can be set by pressing this button.
See page 8 for Direct Mode and page 9 Setup Menu.
. Gain Selection Button (GAIN UP)
This button is used to select the gain of the video
amplifier as follows. (See page 8 for Direct Mode and
page 9 for Setup Menu.)
40.
41.
12.
13.
Title Input Connector (TITLE)
This
connector
is used
to connect
the
optional
Character Generator WJ-KB12 or WJ-KBt5.
Note:
The black & white characters are displayed on the
video monitor. No color is available.
Video Output Connector (VIDEO OUT)
A 1.0 Vp-p/75 ohms composite video signal is provided
at the connector.
Horizontal Drive/Gen-Lock Input Connector
(HD/GEN-LOCK)} (Gen-Lock Mode}
The color video signal of the camera is automatically
synchronized
to the gen-lock
signal (composite
or
black burst) which is supplied to this connector. The
gen-lock signal is used for system reference.
Caution:
If the gen-lock signal is jittery (when obtained from
VTR playback}, the camera
can not be able to
synchronize properly.
(External HD and VD Mode)
The horizontal and vertical phase of the color video
signal is synchronized to the external HD fed to this
connector and external VD fed to the Vertical Drive
(VD) Input Connector (12).
CAUTION
:
Camera functions improperly when only HD or only
VD is fed to the camera control unit.
Vertical Drive Input Connector (VD)
Feed the external Vertical Drive pulse to this connector.
S-VHS Video Output Connector (S- VIDEO OUT)
The luminance {Y) and chroma (C) signals for S-VHS
VTR or monitor are provided at this connector.
ase a
ain of the video amplifier is set to the fixed
14,
-Genloek renminallon Switches
| J
P
(G/L 75 ohms, ON/OFF)
aoe ae
When looping through the gen-lock video input signal,
The video gain increases approximately +6 dB.
MID :
The video gain increases approximately +9 dB.
HI:
The video gain increases approximately +12 dB.
. Setup Mode Button (SET UP}
The camera enters to the user setup-mode by pressing
this button.
. Camera Cable Connector (CAMERA)
This 12-pin connector is used for connection of the
optional camera cable.
15.
set this switch to the OFF position and other cases,
set this to the ON position.
12V DC Input Terminals (DC 12V IN}
This terminal accept an external DC source supplying
nominal power of 12V, 0.5A-0.7A.
CAUTION :
CONNECT THIS TO A DC 12V CLASS 2 POWER
SUPPLY ONLY.
Caution:
To Prevent fire or shock hazard, the UL listed wire VW-1,
style 1007 should be used for the cable for DC 12V input
Terminal.
Caution:
Connecting or disconnecting the camera cable must be
done after turning off the Power ON/OFF Switch.
Advertisement
