Advertisement
Note:
5-1.
While the ALL RESET mode is being processed, picture
may be disturbed.
This phenomenon
is normal and
indicating the sign of the all reset mode.
Entering Setup Menu
By pressing the Setup Mode Button (SET UP) for more
than 1 second, the "SET UP" menu is displayed on the
monitor screen as shown in Fig. 20.
4h SET UP or
SYNC
SHUTTER
CAHERA
IO
ELC
AGC
WHITE
BAL
END
WC
(PUSH
SW)
Fig. 20
By observing this menu, you can check the current
conditions.
Refer to the following sections for details of each item.
After
confirming
current
conditions
and
further
resetting of each item is not required, move the cursor
to the "END" position on the left bottom line and press
the Setup Mode Button (SET UP) to return to the normal
camera picture mode.
Notes:
1, Whenever completing the setup menu, move the
cursor to the "END" position and press the Setup
Mode
Button
(SET
UP) and
confirm
that
the
"SETUP
MENU"
disappears
from the screen
in
order to ensure the latest data to be stored
in the memory.
In addition,
do not connect
or disconnect
the Gen-lock input signal during
setting the "SETUP MENU" as this could cause a
reset of set data.
2. When no key is pressed for 5 minutes while any
of SETUP MENU is being displayed, the SETUP
MENU
is automatically ended and returns to the
normal picture.
wok SET UP oe
SYNC
SHUTTER
CAMERA
IO
ELC
AGC
WHITE
BAL.
ENI 4m
AUC
(PUSH
SW)
Fig. 21
-13-
e
When the Special Menu ts needed to be adjusted, move
the cursor to the "END" position and press both the Left
Button (WHT BAL) and Right Button (GAIN UP} together
for approximately 2 seconds
to display the Special
Menu. (Refer to the 7. SPECIAL MENU on page 21.)
Important Notice:
When the cursor is moved to the next position (next
item) after changing the data (ex. ON — OFF), the latest
data is written on the memory
(Electronic Erasable
Programmable Read Only Memory (EEPROM)) and it
remains until the further data write is made even if the
camera power is switched off.
5-2. Camera Identification (CAMERA ID) Setting
e
Move the cursor to the "CAMERA ID" mode position, and
select either "ON" (Camera Identification character is
displayed) or "OFF" mode by using either the Left Button
(WHT BAL) or Right Button (GAIN UP).
k
SET UP **
INT
OFF =
OFF
ON
SYNC
SHUTTER
CAMERA
ID
ELC
AGC
WHITE
BAL
END
AWC
(PUSH
SW
Fig. 22
e
Move the cursor to the next item to write the new data
into the memory.
e
When
the
camera
identification
character
needs
editing,
perform
the following
steps
by using
the
submenu of Camera identification.
èe
Move the cursor to the "CAMERA ID" mode position and -
press the Setup Mode Button (SET UP) to display the
Character Editing menu as shown in Fig. 23.
Character Cursor
vA
-ABCDEFGHIJKLM
HOPQRSTUVUXYZ
0123956789
OQ.
Rb 2=
+-#/7§
Character Area
e > SPACE
POSI RET END: reset F
Command
Editing Cursor
mro
LH— Editing Area
Fig. 23
e
The character cursor on the letter "A" and the editing
cursor on the left end of the editing area starts blinking.
e
Move
the character cursor
to the desired letter by
using the Up Button (AGC), Down Button (AWC SET),
Left Button (WHT BAL) and Right Button (GAIN UP) and
press the Setup Mode Button (SET UP). The selected
letter is written on the editing cursor.
{The blinking
Editing Cursor
moves
to right automatically
at this
moment.)
e
Repeat this procedure until the character editing has
been completed.
Advertisement
