Advertisement
wk SYNC
Hk
H PHASE
a
ries
i (1--4)
ae
SYNC
tote
H PHASE
oe
aE
SC COARSE
SC FINE
o>
RET
END
RET END
Fig. 38
2. When the Left Button (WHT BAL) or-Right Button
(GAIN
UP) is kept pressed
for more
than one
second, the cursor "l" moves quickly.
3.
For more
accurate
adjustment,
supply
both
the
original camera video output signal and the Effect
Output video signa! (Program Output video signal)
of the Special Effects Generator
(SEG) to the
vectorscope and compare the chroma phase for
both signats.
4. When
both
the
Left
Button
(WHT
BAL)
and
the
Right
Button
(GAIN
UP)
are
pressed
simultaneously, the cursor "I" is reset to the factory
setup position,
5-6-2, VS Gen-lock Mode (EXT(VS))
Connect
the coaxial
cable
of the composite
sync
or composite
black-and-white
video
signal to the
Gen-lock Input Connector (11) and confirm that the
"INT" position has been changed
into the "EXT(VS)"
indication.
4% SET UP +m
SYNC
INT
SHUTTER
OFF
CAMERA
ID
OFF
ELC
OFF
ON
RUC
(PUSH
SW)
wh SET UP wx
i
SYNC
SHUTTER
CAMERA
ID
ELC
AGC
WHITE
BAL
END
AGC
WHITE
BAL
END
AWC
(PUSH
$W)
Fig. 39
CAUTION:
The gen-lock input signal should be met with the
EIA RS-170 specification and should not contain
jitter such as VTR playback signal as it could
cause a synchronization error.
After confirming that the cursor is on the "EXT(VS)°
position, press the Setup Mode Button (SET UP) on the
front panel and following phase adjustment menu
is
then displayed on the monitor.
we SYNC
+
H PHASE
RET
END
Fig. 40
SAF =
Connect
the camera
video
output
signal and
the
gen-lock input signal to a dual-trace oscilloscope.
Set the oscilloscope to the horizontal rate and expand
the horizontal syne portion on the oscilloscope.
Adjust the horizontal phase by using the Left Button
(WHT BAL) or Right Button (GAIN UP). The cursor *I"
moves left or right.
The adjustable range is 0 - 2.5
psec.
5-6-3. External HD/VD Mode (HD/VD)
Connect
the coaxial cable of the external HD and
VD signal to the HD/GEN-LOCK
connector and VD
connector
respectively
and
confirm
that the "iINT"
position changes to the EXT (H/V) indication.
wi SET UP +m
EXT.
OFF
OFF
OFF
ON
AWC
(PUSH
Su
SYHC
SHUTTER
CAMERA
IO
ELC
AGC
WHITE
BAL
END
Fig. 41
No more setting up or adjustment is required.
5-6-4. External VD Mode (VD}
Connect the coaxial cable of the external VD signal to
the VD connector and confirm that the "INT" position
changes to the EXT (VD} indication.
wh SET UP **
SYNC
SHUTTER
CAMERA
I0
ELC
AGC
WHITE
BAL
END
AUC
(PUSH
SW)
Fig. 42
No more setting up or adjustment is required.
5-7. White:Balance Setting (WHITE BAL)
5-7-1. Auto-Tracing White Balance Mode (ATW)
e
Display the Setup menu as shown in Fig. 20.
è
Move the cursor to the "WHITE BAL" mode by pressing
the Left Button (WHT BAL) and the Right Button (GAIN
UP).
tok SET UP et
SYNC
SHUTTER
CAMERA
ID
ELC
AGC
WHITE
BAL
END
Fig. 43
Advertisement
