Advertisement
Quick Links
Advertisement
Related Manuals for WATSON Tonic Dual Sided Workbench
Summary of Contents for WATSON Tonic Dual Sided Workbench
- Page 1 ASSEMBLY Tonic Dual Sided Workbench 360.394.1300 watsonfurniture.com V.23.1 10/2023...
-
Page 2: Important Safety Instructions
This product is for use on a nominal 120-V circuit. Make sure that the product is connected to an outlet having the same configuration as the plug. No adapter should be used with this product. 2 TONIC DUAL SIDED WORKBENCH ASSEMBLY INSTRUCTIONS... - Page 3 Cutting Screw (121406) (121538) M6 1.00 x 12mm 8-32 NUT Screw (125285) (117011) Wing Nut Floor Anchor Tite Joint (888101) (480136) (0002294) DATA MANAGER CLIPS BLANK DATA PORT FLOOR ANCHOR BRACKET (0000003) (0001367) (504608-CP) 3 TONIC DUAL SIDED WORKBENCH ASSEMBLY INSTRUCTIONS...
- Page 4 Tonic Single Sided Workbench Components POWER BRICK END COVER SPLICE PLATE END BRACKET CABLE SLAT INFEED JUMPER CABLE RACEWAY RAIL TOP SUPPORT RAIL END SEGMENT WORK SURFACE POWER RACEWAY END LEG ASSEMBLY MID LEG ASSEMBLY INFILL 4 TONIC DUAL SIDED WORKBENCH ASSEMBLY INSTRUCTIONS...
- Page 5 Driver Bit Driver Bit Driver Bit Driver Bit Additional tools such as a 90 Degree Bit and an 18” Extension are helpful for some steps *No torque or ball bits should be used 5 TONIC DUAL SIDED WORKBENCH ASSEMBLY INSTRUCTIONS...
- Page 6 When assembling 2 or more segments, position the remaining leg assemblies and loosely attach the additional top support rails. Use end legs at the ends and mid legs in-between. M6 1.00 x 12mm Screw (125285) 6 TONIC DUAL SIDED WORKBENCH ASSEMBLY INSTRUCTIONS...
- Page 7 Raceway Rail Loosely attach raceway rails (2 per segment) with 4 screws (125285) per rail. M6 1.00 x 12mm Screw (125285) 7 TONIC DUAL SIDED WORKBENCH ASSEMBLY INSTRUCTIONS...
- Page 8 Attach Anchors (Hardwired Tables Only) Loosen Glide and place through the Floor Anchor Bracket on two Leg Assemblies. Mark and drill ¼" dia. holes and fasten to the floor with provided fasteners (480136). Floor Anchor (480136) 8 TONIC DUAL SIDED WORKBENCH ASSEMBLY INSTRUCTIONS...
- Page 9 Attach End Cover (Aisle and Extension Ends Only) 4. Attach end covers (if included) to the outside of the end legs with 4 wingnuts (888101) per end cover (hand tighten and avoid over tightening) Wing Nut (888101) 9 TONIC DUAL SIDED WORKBENCH ASSEMBLY INSTRUCTIONS...
- Page 10 End Bracket (Extension Ends Only) Insert pairs of end brackets into end of top support rails. 10 TONIC DUAL SIDED WORKBENCH ASSEMBLY INSTRUCTIONS...
- Page 11 Align and fasten End Segment to End Leg with 4 screws (0002147). (Extension End Only) Fasten End Segment to End Bracket with 2 screws (0001247) per bracket. M6 1.00 x 12mm Screw (0002147) 11 TONIC DUAL SIDED WORKBENCH ASSEMBLY INSTRUCTIONS...
- Page 12 Repeat step (b) until all work surfaces are attached. (c) Attach the final end segment to the final pair of work surfaces with tite joints. M6 1.00 x 12mm Tite Joint Screw (0002147) (0002294) 12 TONIC DUAL SIDED WORKBENCH ASSEMBLY INSTRUCTIONS...
- Page 13 Repeat step 8 working your way down the workbench table segments from the previous table segment. Repeat step 6 to attach the final end segment with 1” screws (0002147). (b) Completely secure splice plates to surfaces with 1” screws (0002147). M6 1.00 x 12mm Screw (0002147) 13 TONIC DUAL SIDED WORKBENCH ASSEMBLY INSTRUCTIONS...
- Page 14 (121406). Note: Power bricks should always be on the right side for 2 duplexes per user. (b) Push data manager clips (0000003) into provided holes in top of power raceway. 8-32 x ¼" Screw Lock Washer DATA MANAGER CLIPS (121535) (121406) (0000003) 14 TONIC DUAL SIDED WORKBENCH ASSEMBLY INSTRUCTIONS...
- Page 15 (c) Ground the jumper cable to the power raceway with the provided screws (121538) and washers (121406). Check each connection by slowly pulling on each cable after making a connection. 8-32 x ¼" Screw 8-32 x ¼" Thread Lock Washer (121535) Cutting Screw (121406) (121538) 15 TONIC DUAL SIDED WORKBENCH ASSEMBLY INSTRUCTIONS...
- Page 16 #8 x ¾" screws (122810) as shown below . DO NOT USE THE 1” LONG SCREWS THAT ARE USED TO SECURE THE PRIMARY DESK SURFACES #8 X 3/4” WOOD SCREW INFILL CLIP #10 X 1” WOOD SCREW (122810) (486915) (0002147) 16 TONIC DUAL SIDED WORKBENCH ASSEMBLY INSTRUCTIONS...
- Page 17 (a) Orient Infills above Power Raceways in positions that allow users access to desired outlets on the power. The clips go through the holes on the Raceway Rails. (b) From underneath, slightly turn all clips to secure Infill component in place. 17 TONIC DUAL SIDED WORKBENCH ASSEMBLY INSTRUCTIONS...
- Page 18 Secure Data Cables Cable Slats go underneath the Power Raceway to keep data cables from hanging below the raceway. To install, rotate in between raceway rails until the fit is snug and secure CABLE SLAT 18 TONIC DUAL SIDED WORKBENCH ASSEMBLY INSTRUCTIONS...