Table of Contents
Advertisement
•
The power input at the projector side is considered as the disconnect device. When required to
switch off the projector, to access parts inside, always disconnect the power cord at the projector
side. In case the power input at the projector side is not accessible (e.g. ceiling mount), the socket
outlet supplying the projector shall be installed nearby the projector and be easily accessible, or a
readily accessible general disconnect device shall be incorporated in the fixed wiring.
•
Do not stack or hang projectors without using the stacking frame.
•
Max units in stacked configuration, 3 units.
•
Max units in hanging configuration, 2 units.
•
When hanging projectors on a truss with the Barco stacking frame, always secure the stack with safety
cables between the projectors and the truss.
•
When using the projector in a hanging configuration, always mount 2 safety cables. See installation
manual for the correct use of these cables.
•
Do not place this equipment on an unstable cart, stand, or table. The product may fall, causing serious
damage to it and possible injury to the user.
•
Only place the projector on a stable surface, or mount it securely using an approved ceiling mount rig.
•
It is hazardous to operate without lens or shield. Always switch the output light off when replacing a lens.
•
Lenses or shields shall be changed if they have become visibly damaged to such an extent that their
effectiveness is impaired. For example by cracks or deep scratches.
•
Cooling liquid circuit. The projector contains a cooling circuit filled with Mono-ethylene glycol (1,2-ethane
diol) and inhibitors in aqueous solution (34% active). If the unlikely event that the cooling circuits have a
leak, switch off the device and contact qualified service personnel. The liquid is not for household use.
Keep out of reach of children. Harmful by oral intake. Avoid exposure to pregnant women. Avoid contact
with eyes, skin and clothing. Avoid inhale of the noxious fumes.
•
Never point or allow light to be directed on people or reflective objects within the HD zone.
•
All operators shall have received adequate training and be aware of the potential hazards.
•
In case of using an external cooling system position the hoses of the cooling system so that they will not be
tripped over, pulled, or contact hot surfaces.
To prevent fire hazard
•
Do not place flammable or combustible materials near the projector!
•
Barco large screen projection products are designed and manufactured to meet the most stringent safety
regulations. This projector radiates heat on its external surfaces and from ventilation ducts during normal
operation, which is both normal and safe. Exposing flammable or combustible materials into close
proximity of this projector could result in the spontaneous ignition of that material, resulting in a fire. For this
reason, it is absolutely necessary to leave an "exclusion zone" around all external surfaces of the projector
whereby no flammable or combustible materials are present. The exclusion zone must be not less than 40
cm (16") for this projector.
•
Do not place any object in the projection light path at close distance to the projection lens output. The
concentrated light at the projection lens output may result in damage, fire or burn injuries.
•
Ensure that the projector is solidly mounted so that the projection light path cannot be changed by
accident.
•
Do not cover the projector or the lens with any material while the projector is in operation. . Mount the
projector in a well ventilated area away from sources of ignition and out of direct sun light. Never expose
the projector to rain or moisture. In the event of fire, use sand, CO
use water on an electrical fire. Always have service performed on this projector by authorized Barco
service personnel. Always insist on genuine Barco replacement parts. Never use non-Barco replacement
parts as they may degrade the safety of this projector.
•
Slots and openings in this equipment are provided for ventilation. To ensure reliable operation of the
projector and to protect it from overheating, these openings must not be blocked or covered. The openings
should never be blocked by placing the projector too close to walls, or other similar surface. This projector
should never be placed near or over a radiator or heat register. This projector should not be placed in a
built-in installation or enclosure unless proper ventilation is provided.
•
Projection rooms must be well ventilated or cooled in order to avoid build up of heat. It is necessary to vent
hot exhaust air from projector and cooling system to the outside of the building.
•
Let the projector cool completely before storing. Remove cord from the projector when storing.
To prevent battery explosion
•
Danger of explosion if battery is incorrectly installed.
•
Replace only with the same or equivalent type recommended by the manufacturer.
Safety information
or dry powder fire extinguishers. Never
2
R5911443 /03
UDM
13
Advertisement
Table of Contents
