Sony RM-E700 Service Manual page 14

i
i
Program Editing—To Edit Scenes in Succession
[Operation 4] ty Repeat Operations 2 and 3 to designate the other Cuts.
ePTelieley Finish the designation of the Cuts.
After designating all Cuts, press
the PGM button.
In the display window, PGM turns
from flashing to lighting steadily.
The program has been designated.
OUT point of the last Cut
To preview the program, press
the PREVIEW button. (if you do
not want to preview, skip this step.)
The tape is played back and
exclaimation marks (!) appear at
the corners from the IN point to the
OUT point of the designated Cut.
To stop preview, press the
PREVIEW button or the & STOP
button of the PLAYER section.
To change the IN and OUT points,
see page 27.
TV or monitor
els elielees Perform the program editing.
Locate the editing start point
using the tape transport
buttons and jog/shuttle dial
of the RECORDER section,
and set the recorder to the
recording pause mode.
Lights only in the case
of the connection 1
2
Press the PGM EDIT button.
PGM EDIT lights in the display
window, and the RM-E700 starts
program editing automatically.
[ers
¢ The program editing is not possible when the maximum
recording pause mode period of the recorder is shorter
than the transporting time from a Cut to the next Cut of the
original tape in the player.
« After programming, do not take the original tape out of the
player until the program editing is performed.
To stop program editing
Press the PGM EDIT button.
Or, press the ™ STOP button of either the PLAYER or
RECORDER section.
Note on recording pause mode
For some types of recorders, you must press the record
button in the playback pause mode to enter the recording
pause mode.
To reset the counter of the player to 001w00w00s (00 00)
Press the COUNTER RESET button.
When you edit by the RC time cord, the COUNTER RESET
button does not operate.
To check the total program time
When the counter of the player shows the hour/minute/
second indication, you can check the total program time
together with the designated cut numbers until the last
programmed Cut.
Press the LAP button.
In the display window, 01 and the time of Cut 1 appear, then
the Cut numbers from 2 and the total program time until the
displayed Cut number appear every 1 second in sequence.
Meanwhile, the TOTAL LAP indication appears. After the
time of all the designated Cuts is shown, the Cut number
indication disappears and the total program time remains.
To turn off the total program time, press the LAP button
again. The RM-E700 returns to the programming mode.
COUNTER RESET button —_ LAP button
How the player operates during the program editing
or previewing
During the program editing or previewing, the player starts
to playback from about 15 seconds (about 15 counts for the
4-digit counter) before the iN point. The player stops at
about 2 seconds (about 2 counts for the 4-digit counter)
after the OUT point.
Using the MOVE MODE setector at the rear, you can
select tape transport mode between the Cuts. Set the
MOVE MODE selector before the program editing or
previewing.
¢ To fast-forward or rewind the tape, set to FF/REW.
When the interval between the Cuts is within about 1
second, the player performs normal playback or fast-
forward/reverse playback.
© To playback while fast-forwarding or reversing, set to
CUE/REV (review).
When the interval between the Cuts is within about 15
seconds, the player performs normal playback.
How to use the END MODE selector at the rear
Using the END MODE selector, you can select either the
stop mode or pause mode for the player and recorder to be
set to after program editing, and for the player to be set to
after previewing. Set the END MODE selector before
program editing or previewing.
To set to stop mode - Set the END MODE selector to
STOP.
To set to pause mode — Set the END MODE selector to
PAUSE.
Stop mode is recommended when you may leave the site
during program editing or previewing.
Pause mode is recommended when:
* you continue program editing.
you find out a Cut to be changed during previewing.
io
GER Top a0ds
FF/REW. CUE/REV
MOVE MODE
enti
25