Table of Contents
Advertisement
Connection 4
5) Col glare Mdat- Mal Ulaled
(Col
al-Mel Ml lal-mat-uile) (=m Ore)
When you use an other manufacturer's recorder, store the
control signal of the tape transport, so that the RM-E700 can
operate the recorder.
However, you cannot use the jog/shuttle dial to operate
the recorder.
Operation
Turn on the power of the
RM-E700.
ol Unit in the RM-E700
To avoid mistakes in editing, store at least the following six
functions of the remote control unit on the same button of
the RM-E700.
® (playback), REC (recording), STOP, H (pause), &
(fast-
forward), << (rewind)
Point the remote control unit of the recorder at the infrared beam detector of the RM-E700.
Press the COMMAND
MEMORY button.
The RM-E700 enters the learning
mode.
The ERISEd@iaag 'ndication lights up,
and the PAUSE indication flashes
in the display window.
flashing
lit
While PAUSE is flashing,
keep pressing the Il button of
the remote control unit of the
recorder. When PAUSE lights
up, release the fl button.
The RM-E700 has learned the
pause function. Then > (playback)
flashes.
about 3~5 cm
(1/16 ~2 inches)
lit flashing
Remote control
unit of the recorder
18
While > is flashing, keep
pressing the > button of the
remote control unit of the
recorder. When > lights up,
release the > button.
The RM-E700 has learned the
playback function. Then >> (fast-
forward) flashes.
about 3~5 cm
(1°he ~2 inches)
Remote control
unit of the recorder
Repeat step 3 or 4 to store the functions of other buttons.
The indicator flashes in the order of:
CO (fast-forward) — <kKJ (rewind)
+ STOP > REC (recording) — D> (frame advance playback)
— [> (slow speed playback) — x2 (double speed playback)
When the RM-E700 has learned all the functions, the learning mode is cancelled after 3 seconds.
Check that the recorder operates correctly by pressing the buttons of the RECORDER section.
If the recorder does not operate correctly, try again from step 2.
¢ To turn off the power of the RM-E700, first turn the
POWER switch off, then disconnect the AC power
adaptor from the RM-E700. If you do this in the reverse
order, the stored data will be erased, and the lithium
battery will be consumed quickly.
* The RM-E700 cannot store the functions of some remote
control units such as those using supersonic waves.
Press the button within 30 seconds
Press the button within 30 seconds while the indication is
flashing. Otherwise the indications disappear and learning
mode is canceled. In this case, try again from step 2.
When the remote control unit of the recorder does not
have the same button as the flashing indication
You can store any desired function for the flashing button.
Press the desired button.
To cancel the learning operation
Repeat pressing the COMMAND MEMORY button until the
x2 indication flashes. Press the COMMAND MEMORY
button again.
To erase the stored function
Press the AC button while the
indication is on.
To change the stored function
Repeat pressing the COMMAND
MEMORY button until the
indication to be changed appears. Press the button of the
function to be stored instead. The previous function is
erased.
Press the button firmly for more than 3 seconds until the
indication changes from flashing to lighting steadily. Then
wait for 1 second after the next indication starts flashing,
and store the next function.
¢ Do not press another button until the indication stops
flashing.
© During the learning operation, you cannot control the
player and recorder with the RM-E700.
¢ When the power is turned off during the learning
operation, the stored data will be erased.
During the learning operation, do not move the RM-E700
and the remote contro} unit.
19
Advertisement
Table of Contents
