Makita RP1800 Instruction Manual
Hide thumbs
Also See for RP1800:
- Instruction manual (100 pages) ,
- Instruction manual (16 pages) ,
- Instruction manual (76 pages)
Related Manuals for Makita RP1800
Summary of Contents for Makita RP1800
- Page 1 INSTRUCTION MANUAL Router RP1800 RP1800F RP1801 RP1801F RP2300FC RP2301FC DOUBLE INSULATION Read before use.
-
Page 2: Specifications
SPECIFICATIONS Model RP1800/ RP1801/ RP2300FC RP2301FC RP1800F RP1801F Collet chuck capacity 12 mm or 1/2" Plunge capacity 0 - 70 mm No load speed (min 22,000 9,000 - 22,000 Overall length 312 mm Net weight 6.0 kg 6.1 kg Safety class •... - Page 3 If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock. Use of power supply via an RCD with a rated residual current of 30 mA or less is always recommended.
-
Page 4: Router Safety Warnings
Service WARNING: DO NOT let comfort or familiarity Have your power tool serviced by a qualified with product (gained from repeated use) replace repair person using only identical replacement strict adherence to safety rules for the subject parts. This will ensure that the safety of the power product. -
Page 5: Nylon Nut
Nylon nut Switch action ► 1 . Nylon nut ► 1 . Lock button 2. Switch trigger The upper limit of the tool body can be adjusted by turning the nylon nut. CAUTION: • Before plugging in the tool, always check to see CAUTION: that the switch trigger actuates properly and •... - Page 6 Speed adjusting dial Lighting up the lamps For model RP2300FC,RP2301FC only For model RP1800F, RP1801F, RP2300FC,RP2301FC only ► 1 . Speed adjusting dial ► 1 . Lamp The tool speed can be changed by turning the speed adjusting dial to a given number setting from 1 to 6. CAUTION: Higher speed is obtained when the dial is turned in the direction of number 6.
-
Page 7: Operation
When doing edge cutting, the workpiece surface should CAUTION: be on the left side of the bit in the feed direction. • Install the bit securely. Always use only the wrench provided with the tool. A loose or over- tightened bit can be dangerous. •... - Page 8 When cutting, move the tool with the straight guide flush Straight guide with the side of the workpiece. If the distance between the side of the workpiece and the cutting position is too wide for the straight guide, or if the side of the workpiece is not straight, the straight guide cannot be used. In this case, firmly clamp a straight board to the workpiece and use it as a guide against the trimmer base.
- Page 9 When set to minimum opening width Fine Adjusting Function for Positioning Blade in Relation to Straight Guide When set to maximum opening width ► 1 . Adjusting screw Loosen thumb nut (M6 x 50mm). Thumb nut (M10 x 52mm) can be turned to adjust position (one turn adjusts the position by 1mm). After completing position adjustment, tighten thumb nut (M6 x 50mm) until secure. Scale ring can be rotated separately, so scale unit can be aligned to zero (0).
- Page 10 To install the templet guide, pull the lock plate lever and Trimmer guide (optional accessory) insert the templet guide. ► 1 . Template guide 2. Lock plate Trimming, curved cuts in veneers for furniture and the like can be done easily with the trimmer guide. The Secure the templet to the workpiece.
- Page 11 Dust nozzle set (Accessory) How to use screw M6 x 135 for adjusting the depth of cut When using the tool with a router table available in the market, using this screw allows an operator to obtain a small amount of adjustment of the depth of cut from above the table.
-
Page 12: Maintenance
Then check the tool while running and electric ► 1 . Screwdriver brake operation when releasing the switch trigger. If electric brake is not working well, ask your local Makita service center for repair. To maintain product SAFETY and RELIABILITY, repairs,... - Page 13 "V"Grooving bit Router bits Straight bit 1/4" Drill point flush trimming bit 1/4" 1/2" 1/2" 1/4" 1/4" "U"Grooving bit Drill point double flush trimming bit 13 ENGLISH...
- Page 14 Board-jointing bit Cove beading bit Corner rounding bit Ball bearing flush trimming bit 1/4" Chamfering bit Ball bearing corner rounding bit 1/4" 14 ENGLISH...
- Page 15 Ball bearing chamfering bit Ball bearing cove beading bit 1/4" Ball bearing roman ogee bit Ball bearing beading bit 15 ENGLISH...
- Page 16 Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan 884877A922 www.makita.com 20211026...