Makita RP2301FC Instruction Manual
Hide thumbs Also See for RP2301FC:


Quick Links

IMPORTANT: Read Before Using.


Table of Contents

Summary of Contents for Makita RP2301FC

  • Page 1 INSTRUCTION MANUAL Router RP1800 RP1800F RP1801 RP1801F RP2300FC RP2301FC 009852 DOUBLE INSULATION IMPORTANT: Read Before Using.
  • Page 2: Specifications

    ENGLISH (Original instructions) SPECIFICATIONS RP1800 / RP1801 / Model RP2300FC RP2301FC RP1800F RP1801F Collet chuck capacity 12 mm or 1/2" Plunge capacity 0 - 70 mm No load speed (min 22,000 9,000 - 22,000 Overall length 312 mm Net weight 6.0 kg...
  • Page 3 EC Declaration of Conformity The typical A-weighted noise level determined according Makita Corporation responsible to EN60745: manufacturer declare that the following Makita Sound pressure level (L ) : 86 dB(A) machine(s): Sound power level (L ) : 97 dB(A) Designation of Machine:...
  • Page 4 Keep children and bystanders away while 15. Do not overreach. Keep proper footing and operating a power tool. Distractions can cause balance at all times. This enables better control you to lose control. of the power tool in unexpected situations. Electrical safety 16.
  • Page 5: Router Safety Warnings

    27. Keep handles dry, clean and free from oil and WARNING: grease. GEB018-3 DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence ROUTER SAFETY WARNINGS to safety rules for the subject product. MISUSE or Hold power tool...
  • Page 6 Electronic function Adjust the lowest hex bolt to obtain the deepest depth of For model RP2300FC,RP2301FC only cut, following the method of "Adjusting depth of cut". Constant speed control Adjust the two remaining hex bolts to obtain shallower Possible to get fine finish, because the rotating •...
  • Page 7 Either can lead to breakage of the collet Lighting up the lamps cone. Use only router bits of which the maximum speed, For model RP1800F, RP1801F, RP2300FC,RP2301FC • as indicated on the bit, does exceed the maximum only speed of the router.
  • Page 8: Operation

    OPERATION dimensions. When using the straight guide or the trimmer guide, • be sure to install it on the right side in the feed CAUTION: direction. This will help to keep it flush with the side Before operation, always make sure that the tool •...
  • Page 9 Fine Adjusting Function for Positioning Blade 1. More than 15 in Relation to Straight Guide 2. Straight guide 1. Adjusting screw 3. Wood 55 mm 55 mm 004931 When using a large diameter bit, attach pieces of wood 009873 to the straight guide which have a thickness of more than 15 mm to prevent the bit from striking the straight Loosen thumb nut (M6 x 50mm).
  • Page 10 guide. The distance (X) can be calculated by using 1. When set to the following equation: maximum Distance (X) = (outside diameter of the templet opening width guide - bit diameter) / 2 Trimmer guide (optional accessory) 009870 Templet guide (optional accessory) 009867 Trimming, curved cuts in veneers for furniture and the like can be done easily with the trimmer guide.
  • Page 11 Dust nozzle set (Accessory) 1. Installing the screw and washer on the tool Attach flat washer onto this screw. • Insert this screw through a screw hole in the tool • base and then screw in the threaded part in the motor bracket of the tool.
  • Page 12: Optional Accessories

    If 1. Screwdriver electric brake is not working well, ask your local Makita service center for repair. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized Service Centers, always using Makita replacement parts.
  • Page 13 Router bits "V"Grooving bit Straight bit 005118 005116 1/4" 006454 1/4" Drill point flush trimming bit 1/2" 1/2" 1/4" 1/4" 006452 005120 "U"Grooving bit 006456 Drill point double flush trimming bit 005117 006453 005121 006457...
  • Page 14 Board-jointing bit Cove beading bit 005123 005129 006459 006464 Corner rounding bit Ball bearing flush trimming bit 005125 005130 006460 1/4" 006465 Chamfering bit Ball bearing corner rounding bit 005126 005131 1/4" 006462 006466...
  • Page 15 Ball bearing chamfering bit Ball bearing roman ogee bit 005132 005135 1/4" 006470 006467 NOTE: Ball bearing beading bit Some items in the list may be included in the tool • package as standard accessories. They may differ from country to country. 005133 006468 Ball bearing cove beading bit...
  • Page 16 Makita Corporation Anjo, Aichi, Japan 884877D225...

Table of Contents