Table of Contents
Advertisement
BASIC OPERATION
How to turn ON/OFF the power of
the transmitter
®
Windows
Embedded Compact 7 is installed as a built-
in operating system in the T32MZ-WC transmitter.
Compared to the conventional system, the T32MZ-WC
takes extra time for internal processing when it is turned
on/off.
When・turning・on・the・power・of・the・transmitter
1. Place the throttle stick below 1/3 closed.
2. Turn on the power switch.
*After initialization of the transmitter is complete, the LED
monitor turns Purple.
*If your throttle stick is not at 1/3 closed or fully closed, a
warning will sound. If you move the throttle to 1/3 closed
or fully closed, the warning will stop and will become a
"Transmit ?" screen.
*If you push the button "NO", then the transmitter will not
emit radio waves.
*If you push the button "Yes", then the transmitter will emit
radio waves.
*If a battery is removed and it re-connects, please switch
on a power supply, after 3 seconds or more pass.
Start-up time;
The time required to initialize the internal circuit of the
transmitter varies between the previous time you turned the
power off and then restarted the transmitter. There are two "start
up" modes for your transmitter, see below:
Cold start;
If you turn on the transmitter more than four hours after you last
turned it off, the mode is "Cold start". "Cold start" is normal for
the first initial power up of the day. It will take about 30 seconds
to be ready for use, as it takes time to initialize the internal
circuit of the transmitter.
Hot start;
If you turn on the transmitter less than four hours after you last
turned it off, the mode is "Hot start". Since initialization has
been partly completed, the transmitter will be ready to use in
several seconds. Since initialization has been partly completed,
the transmitter will be ready to use in several seconds. "Hot start"
takes place usually at a second flight or later flight in the day.
WARNING
Once・ you・ turn・ on・ the・ power,・ never・ shut・ off・ the・ power・
switch・until・the・power・becomes・stable・(or・until・the・first・screen・
shows・up).・If・you・turn・off・the・power・switch・while・the・transmit-
ter・is・going・through・the・initialization・process,・the・data・could・be・
damaged.・
Note: The start-up time may be a little bit slower when the
microSD card is installed compared to when the card is not.
30
The center switch
is pushed.
How・to・stop・the・transmitter
Turn off the power switch of the transmitter. The internal
circuit of the transmitter starts the shut down process
including saving the set-up data.
Once・ you・ turn・ off・ the・ power,・ never・ operate・ the・ power・
switch・ until・ the・ power・ shutdown・ process・ is・ fully・ completed.・ If・
you・turn・on・the・power・switch・again・while・the・transmitter・is・still・
in・the・process・of・power・shutdown,・the・data・could・be・damaged.
How・to・reset・software
If the screen freezes for some reason and you cannot
edit, the transmitter power supply is not fully off even if
you turn OFF the power switch. You will need to remove
the battery and reinsert it again. In this case, the power
restarts in "Cold mode". Even though the screen freezes,
all the other functions for radio control operation remain
operative.
Quick start
This "screen off" can quick start next startup. This is
convenient when turning on and off frequently. No RF
output at "screen off". Also, there is no screen display.
However, the battery is consumed because the internal
circuit is activated.
HOME/EXIT
Screen OFF
Turn ON →
WARNING
While・ in・ screen・ off・ mode,・ it・ consumes・ about・ 4%・ of・
the・battery・per・hour.・If・you・do・not・use・the・transmitter・for・
a・long・time,・turn・off・the・power.
Updates・cannot・be・performed・in・screen・off・mode.・To・
update,・turn・off・the・power.・
→
GO to TABLE OF CONTENTS
Push and hold
the center
switch.
Be sure to turn off
the receiver first.
While holding down
the HOME / EXIT
button, turn off the
power switch.
Screen off mode.
Quick start
Advertisement
Table of Contents
