Radiator+engine bay protection for: isuzu d-max (2021-) (33 pages)
Summary of Contents for Rival 2M.2701.1MB
Page 1
COMPONENTS OF THIS ROOF RACK (2M.0001.4, 2M.0003.4, 2M.2701.K, 2MD.0020.1) You can also refer to full installation video on our Youtube Channel “RIVAL 4x4 Accessories” CAUTION! To reduce the risk of serious injury or damage, please read and understand all instructions and procedures before attempting to install or use this product.
Page 2
Aluminum SAFETY NOTICE * The RIVAL roof rack is designed to compliment the use and design of the specified vehicle under conditions specified by the car manufacturer. * While driving the vehicle at any speed, collision with any other vehicle, animal or object must always be avoided.
Page 5
5. Place connector 8 (item 12) into slot of side M8x20 (item 10) and spring washer 8 (item profile (item 2). Align the holes. 11). *Do not tighten yet. Installation manual 2M.2701.1MB Date: 11-Sep-2023 www.rival4x4.com < Page 5 of 20 >...
Page 6
12. Take standard slats (item 3) and slide the 2+6) and frame slat (item 1) to build roof rack one end into side profile (item 2+6), as shown frame, as shown in fig. 11. in fig.12. Installation manual 2M.2701.1MB Date: 11-Sep-2023 www.rival4x4.com < Page 6 of 20 >...
Page 7
15. Loosely install washers 8 (item 9) and nuts with the bolts (item 7) sitting in standart slats (item (item 3) as shown in fig. 16. *Do not tighten yet. Installation manual 2M.2701.1MB Date: 11-Sep-2023 www.rival4x4.com < Page 7 of 20 >...
Page 8
(fig.20). as shown in fig.21. Fig. 22 20. Fix cross bars using washer 8 (item 9) and nut M8 (item 8). *Do not tighten yet. Installation manual 2M.2701.1MB Date: 11-Sep-2023 www.rival4x4.com < Page 8 of 20 >...
Page 9
You’ll have following dimensions: 86.2 inch/ 2190 mm. Fig. 25 Fig. 26 22. Tighten hardware after that. Hold bolt head on frame slat (item 1) using flat screwdriver. Installation manual 2M.2701.1MB Date: 11-Sep-2023 www.rival4x4.com < Page 9 of 20 >...
Page 10
PARTS LISTING Open the box 2M.2701.K 1. Front bracket ........Qty 4 2. Rear bracket ........Qty 2 3. Clamp..........Qty 6 4. Support bracket........ Qty 6 Installation manual 2M.2701.1MB Date: 11-Sep-2023 www.rival4x4.com < Page 10 of 20 >...
Page 11
Qty 6 D. Washer spring 8......Qty 18 E. Washer 8........Qty 36 F. Nut M8..........Qty 18 G. Rubber weatherstrip...... Qty 6 H. Rubber gasket....... Qty 6 Installation manual 2M.2701.1MB Date: 11-Sep-2023 www.rival4x4.com < Page 11 of 20 >...
Page 12
25. Adjust bolts as shown in fig. 31. 26. Install front bracket (item 1) using washers 8 (item E) and nuts M8 (item F) as shown in fig. 32. *Do not tighten yet. Installation manual 2M.2701.1MB Date: 11-Sep-2023 www.rival4x4.com < Page 12 of 20 >...
Page 13
37. Tighten hardware on and adjust this distance to 15.6 inches (395 front bracket installed into 1st standard slat. mm). Tighten hardware on front bracket installed into 3rd standard slat. Installation manual 2M.2701.1MB Date: 11-Sep-2023 www.rival4x4.com < Page 13 of 20 >...
Page 14
35. Adjust bolts as shown in fig. 43. 36. Install rear bracket (item 2) using washers 8 (item E) and nuts M8 (item F). Fig. *Do not tighten yet. Installation manual 2M.2701.1MB Date: 11-Sep-2023 www.rival4x4.com < Page 14 of 20 >...
Page 15
41. Attach rubber gaskets (item H) on sup- bracket (item 4) with the sides of the roof port brackets (item 4), as shown in fig. 50. bracket as shown in fig. 49. Installation manual 2M.2701.1MB Date: 11-Sep-2023 www.rival4x4.com < Page 15 of 20 >...
Page 16
42. Install rubber weatherstrips (item G) on 43. Repeat steps 1-20 for the other side of modular roof rack. Fig. 52. front and rear brackets (item 1,2) as shown in fig. 51. Installation manual 2M.2701.1MB Date: 11-Sep-2023 www.rival4x4.com < Page 16 of 20 >...
Page 17
Qty 1 3. Bracket 2........Qty 1 С С А. Bolt M8x20........Qty 4 B. Screw M8x20......... Qty 4 C. Washer 8........Qty 12 D. Nut M8..........Qty 8 Installation manual 2M.2701.1MB Date: 11-Sep-2023 www.rival4x4.com < Page 17 of 20 >...
Page 18
46. Install and fix the wind deflector (item 1) to brackets 1,2 (item 2,3) using screws M8x20 (item B), washers 8 (item C), nuts M8 (item D) (fig.56). *Do not tighten yet. Installation manual 2M.2701.1MB Date: 11-Sep-2023 www.rival4x4.com < Page 18 of 20 >...
Page 19
1,2) using screws M8x30 (item C), spring washers 8 (item D) and washers 8 (item E), as shown on fig. 59,60. *Tighten hardware after that. Fig. 61 50. Adjust and fix the wind deflector as shown in fig.61. Installation manual 2M.2701.1MB Date: 11-Sep-2023 www.rival4x4.com < Page 19 of 20 >...
Page 20
INSTALLATION PROCEDURE Before operating a vehicle fitted with a RIVAL Roof rack 2M.2701.1MB: - make sure all fittings are tightened Thank you for your choice! Sincerely, RIVAL 4x4 Team Installation manual 2M.2701.1MB Date: 11-Sep-2023 www.rival4x4.com < Page 20 of 20 >...
Need help?
Do you have a question about the 2M.2701.1MB and is the answer not in the manual?
Questions and answers