Download
Share
Print this page
Rival 2D.2701.1-NL Installation Manual
  1. Manuals
  2. Brands
  3. Rival Manuals
  4. Automobile Accessories
  5. 2D.2701.1-NL
  6. Installation manual

Rival 2D.2701.1-NL Installation Manual

Front bumper
Hide thumbs Also See for 2D.2701.1-NL:

Advertisement

Quick Links

Download this manual
INSTALLATION MANUAL
PRODUCT:
MODEL:
PART NO:
CAUTION!
To reduce the risk of serious injury or damage, please read and understand all instructions and
procedures before attempting to install or use this product.
Safety glasses must be worn at all times during installation or maintenance of this product.
Ensure all mounting bolts are tensioned after 400 kms/250 miles and periodically there after.
NOTICE
Whilst the bumper adds additional protection to your vehicle, precautionary measures still need
to be taken to avoid damage.
Always drive to the conditions and your surroundings
FRONT BUMPER
JEEP WRANGLER JK (2007-2018)
JEEP WRANGLER JL (2018-)
JEEP GLADIATOR JT (2019-)
2D.2701.1-NL
2D.2702.1-NL
www.rival4x4.com

Advertisement

loading
Need help?

Need help?

Do you have a question about the 2D.2701.1-NL and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Rival 2D.2701.1-NL

Summary of Contents for Rival 2D.2701.1-NL

  • Page 1 JEEP WRANGLER JK (2007-2018) JEEP WRANGLER JL (2018-) JEEP GLADIATOR JT (2019-) PART NO: 2D.2701.1-NL 2D.2702.1-NL CAUTION! To reduce the risk of serious injury or damage, please read and understand all instructions and procedures before attempting to install or use this product.

  • Page 2: Front Bumper

    * A winch with a pull capacity of up to and including 12000 lb can be installed with the RIVAL Bumper. It is not advisable to exceed this pulling capacity since damage, injury or death may occur where the 12000lb recommended capacity is exceeded.

  • Page 3: Technical Information

    TECHNICAL INFORMATION *WINCH INSTALLATION A winch with a pull capacity of up to 12000 lbs can be installed with the RIVAL Bumper. It is not advisable to exceed this pulling capacity since damage, injury or death may occur where the 12000 lbs recommended capacity is exceeded.
  • Page 4 КОМПЛЕКТАЦИЯ PARTS LISTING Front full width bumper 2D.2701.1-NL Front stubby bumper 2D.2702.1-NL Aluminum bumper body ..Qty 1 7. LED brackets......Qty 2 Qty 1 Qty 1 2. Winch bracket......8. Skid plate....... 3. Left adapter......Qty 1 9. Skid plate bracket left (JK)..
  • Page 5 КОМПЛЕКТАЦИЯ PARTS LISTING *Included only in 2D.2701.1-NL full width bumper 2D.2701.1-NL full width bumper A. Screw M6x20........Qty 10 Qty 6 O. Countersunk washer......B. Screw M6x35........Qty 2 Qty 6 P. Insert nut М10х65/15......C. Screw М10х30........Qty 16 Qty 2 Q.

  • Page 6: Installation Procedure

    Unscrew 8 nuts from the OE bumper 5. Disconnect the fog light wire harness. (four on each side). Remove OE bumper, remove horn. Installation manual 2D.2701.1-NL, 2D.2702.1-NL www.rival4x4.com Date: May 25, 2020 < Page 6 of 12 >...
  • Page 7 6x20 (pos.A), washers 6 (pos.F), nuts M12 (pos. J) and two (pos.K), nuts M6 (pos.H). washers 12 (pos. N). Do not tighten yet. Installation manual 2D.2701.1-NL, 2D.2702.1-NL www.rival4x4.com Date: May 25, 2020 < Page 7 of 12 >...
  • Page 8 M10x20 (pos.E), washers 10 (pos.9,10) using bolts M10x20 (pos.E), (pos.L) and nuts M10 (pos.I). washers 10 (pos.L) and inner bracket (pos.P) on both sides. Installation manual 2D.2701.1-NL, 2D.2702.1-NL www.rival4x4.com Date: May 25, 2020 < Page 8 of 12 >...
  • Page 9 M10 (pos.V). winch plate bracket using screw M10x30 (pos. C), washers 10 (pos. L) and nut M10 (pos. I). Tighten hardware after that Installation manual 2D.2701.1-NL, 2D.2702.1-NL www.rival4x4.com Date: May 25, 2020 < Page 9 of 12 >...
  • Page 10 Инструкция по установке INSTALLATION PROCEDURE LED lights installation For 2D.2701.1-NL full width bumper only 5 Install LED lights to LED brackets 6 Install LED lights from the inside of (pos.7). the bumper. Fix it using screws M6x20 (pos.A), washer 6 (pos.K).
  • Page 11 (pos.1). Screw screws №3 in skid plate brackets (pos.9,10 for JK) or (pos.11,12 for JL, JT). Tighten all hardware after that. Installation manual 2D.2701.1-NL, 2D.2702.1-NL www.rival4x4.com Date: May 25, 2020 < Page 11 of 12 >...
  • Page 12 Инструкция по установке INSTALLATION PROCEDURE Before operating a vehicle fitted with RIVAL Bumper 2D.2701.1-NL or 2D.2702.1-NL: - make sure all fittings are tightened - check winch operation - check all electrical wiring attached to lights Thank you for your choice!

This manual is also suitable for:

2d.2702.1-nl