Modern Flames Landscape Pro LPM-4416V2/INT Installation Manual

Modern Flames Landscape Pro LPM-4416V2/INT Installation Manual

Multi electric fireplace

Advertisement

Quick Links

Landscape Pro Multi Electric Fireplace
Model#
LPM-4416V2/INT
LPM-8016V2/INT
WARNING
CAUTION
AFFIX SERIAL NUMBER LABEL
HERE FOR FUTURE REFERENCE
LPM-9616V2/INT
Installation Manual
Approved for Indoor and Outdoor Use
Rated: 220~240VAC 50/60Hz 6,800 BTUS
Read and understand this entire owner's manual, including all safety
information, before plugging in or using this product. Failure to do so
could result in fire, electric shock, or serious personal injury. Don't
spray water directly on to product. Clean with damp cloth or duster.
Keep this owner's manual for future reference. If you sell or give this
product away, make sure this manual accompanies this product.
LPM-5616V2/INT
LPM-6816V2/INT
LPM-12016V2/INT
07-00011-1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Landscape Pro LPM-4416V2/INT and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Modern Flames Landscape Pro LPM-4416V2/INT

  • Page 1 Landscape Pro Multi Electric Fireplace Model# LPM-4416V2/INT LPM-5616V2/INT LPM-6816V2/INT LPM-8016V2/INT LPM-9616V2/INT LPM-12016V2/INT Installation Manual Approved for Indoor and Outdoor Use Rated: 220~240VAC 50/60Hz 6,800 BTUS Read and understand this entire owner’s manual, including all safety information, before plugging in or using this product. Failure to do so WARNING could result in fire, electric shock, or serious personal injury.
  • Page 2: Important Safety Information

    IMPORTANT SAFETY INFORMATION! WARNING When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: 1. Read all Instructions before installing or using the heater. 2. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, etc.
  • Page 3: Important Instructions

    IMPORTANT INSTRUCTIONS ATTENTION When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: 1. Read all Instructions before installing or using the heater. 2. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, etc.
  • Page 4: Care & Cleaning

    USER INSTRUCTIONS POWER DATA LPM-4416V2/INT LPM-5616V2/INT LPM-6816V2/INT LPM-8016V2/INT LPM-9616V2/INT LPM-12016V2/INT Volts/HZ Amps AC 220~240V AC 220~240V AC 220~240V AC 220~240V AC 220~240V AC 220~240V 50/60Hz 9 Amps 50/60Hz 9 Amps 50/60Hz 9 Amps 50/60Hz 9 Amps 50/60Hz 9 Amps 50/60Hz 9 Amps Heater AC 220~240V AC 220~240V...
  • Page 5: Product Guide

    PRODUCT GUIDE DRYWALL STOPS DRYWALL STOPS 632mm (all models) 24 7/8” 294mm Width varies (see chart below) (all models) 11 9/16” Model Viewing Area Firebox Dimensions Framing Dimensions LPM-4416V2/INT 1099 mm W x 403 mm H x 135 mm D 1120 mm W x 632 mm H x 294 mm D 1128 mm W x 642 mm H x 305 mm D 43 1/4"...
  • Page 6: Parts And Hardware

    PARTS AND HARDWARE Bracket (1) Canyon (1) Fireplace (1) Owners Manual (6) Screws (1) Remote Driftwood Logs Set (2-4) L-Metal (Depend on Model) (1) Front Glass (2) Metal Side Panels (2) Side Glass (2) Suction Cups Mounting Brackets (1) Wall Mount Smoke Clear (1) 5-Piece Trim Kit...
  • Page 7: Installation

    INSTALLATION Select a suitable location that is away from drapes, furniture, and high traffic areas. NOTE: Follow all National and local electrical codes. This product includes a GLASS panel. Always use extreme caution when handling glass. Failure to do so could result in personal injury or property damage. Due to the many different materials used on different walls, it is highly recommended that you consult your local builder before you install this fireplace.
  • Page 8: Built-In Installation

    BUILT-IN INSTALLATION 3 Sided Installation (Bay) 1. Prepare the framed opening according to the chart on page 4. *Provide appropriate dedicated circuit for hardwire install at the top right of framed opening. 2. Install L Metal mounting brackets to the top and bottom of the fireplace with supplied screws.
  • Page 9 BUILT-IN INSTALLATION Fully Recessed Installation (Left/Right Corner) 1. Follow steps from the 3-sided installation instructions. 2. Remove the corresponding drywall stops according to your installation (in the example, the drywall stops on the left end would be removed.) 3. Install the side glass then the corresponding side cover according to your installation (the side glass must be installed before the metal side cover.
  • Page 10 BUILT-IN INSTALLATION Fully Recessed Installation (Single Sided) 1. Follow steps from the 3 sided installation instructions. 2. Remove the drywall stops on both sides of the fire unit. 3. Install the side glass then side covers on both sides of the fire unit (the side glass must be installed before the metal side cover.
  • Page 11 BUILT-IN INSTALLATION Half Recessed Installation 1. This installation is optimized for a 2x4 framed wall. Prepare the framed opening according to the height and width of the chart on page 4. *Provide appropriate dedicated circuit for hardwire install at the top right of framed opening. 2.
  • Page 12: Outdoor Installation Requirements

    OUTDOOR INSTALLATION REQUIREMENTS The LPM Series electric fireplaces from Modern Flames LLC have been tested and approved for installation outdoors under a patio cover and away from direct water contact or direct sun light. Modern Flames LLC standard warranty applies if installed per instructions. All electrical wiring shall be to local building codes.
  • Page 13 OUTDOOR INSTALLATION REQUIREMENTS Side Protection: Side distance (SD) must be 50% (or more) of the height(H). If: H=6’ Then: SD=3’ minimum (6’ x 50%=3’) Note: H taken from bottom of fireplace. OVERHANG HEIGHT (H) SIDE DISTANCE SIDE DISTANCE (SD) (SD)
  • Page 14: Installing Media

    BUILT-IN INSTALLATION Suite Wall Mount & Recessed Cabinet Installation Follow the directions included with the Suite Wall Mount Accessory Kit. INSTALLING MEDIA PROPRIETARY AND CONFIDENTIAL THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF <INSERT COMPANY NAME HERE>. ANY REPRODUCTION IN PART OR AS A WHOL WITHOUT THE WRITTEN PERMISSION OF <INSERT COMPANY NAME HERE>...
  • Page 15: Log Placement

    LOG PLACEMENT #1 LOG #2 LOG #3 LOG #4 LOG #5 LOG #6 LOG #7 LOG #8 LOG #9 LOG #10 LOG #11 LOG #12 LOG #13 LOG #14 LOG #15 LOG LANDSCAPE PRO MULTI - LOG PLACEMENT 44" - 56" - 68" - 80" - 96" - 120" LPM 44"...
  • Page 16: Glass Installation

    GLASS INSTALLATION Installing Side Glass 1. The unit has 2 channels, one on the top and one on the bottom to hold the side glass. 2. Insert the glass at an angle in to the top channel. 3. Swing the bottom edge of the side glass in to the unit. See Figure 1.1.
  • Page 17: Hard Wiring

    HARD WIRING L1 L2 A qualified electrician must wire this fireplace to a dedicated 220~240 volt, 13 amp (EU) 10 amp (AU/NZ), circuit. A 13 amp (EU) or 10 amp (AU/NZ) circuit is required. A dedicated circuit is preferred but not essential in all cases. A dedicated circuit will be required if after installation, the circuit breaker trips on a regular basis.
  • Page 18: Remote Control Operation

    . If the fireplace is on, this button will act as a Home reset and bring all colors back to the default Modern Flames' signature color. This will cycle the heater between high, Heat low and off .
  • Page 19: Setting Controls

    SETTING CONTROLS Manual Controls Toggle Switch: The fireplace has a main toggle switch located next to the manual controls. The fireplace has manual controls located next to the The toggle switch is in front of the glass on toggle switch, in front of the glass on the top right the top right side of the viewing area.
  • Page 20 SETTING CONTROLS NOTE: When silent mode is selected, a tone will still -AP Mode: While the fireplace is ON, long press be present for performing system functions the Preset Color button for 6 seconds. Two such as remote pairing or Wi-Fi pairing. audible beeping tones will sound and then only the FLAME LIGHTS and nothing else will turn to Placing in Wi-Fi Paring Mode:...
  • Page 21: Wifi Remote

    WIFI REMOTE Sync This is a synchronization selector, used to synchronize the current color on the color wheel to all of the zones (Flame/Ember Bed/Downlight). Grayed out SYNC is when synchronization is “OFF”. Green SYNC is when synchronization is “ON”. Color Wheel This is the color adjustment wheel for all zones.
  • Page 22: Mode Sub Menu

    Same as remote control blue monochrome fade cycle. PRESET MENU > Seven Color Demo Same as remote control, 7 color jump > Modern Flames Original cycles: R->G->B->RG->RB->GB->RGB. Modern Flames Orange (Static). > Three Color Demo Same as remote control, 3 color jump >...
  • Page 23 WI-FI REMOTE Timer Pressing the timer button will pop up a sub-menu with 10 options to choose from: 0.5-1-2-3-4-5-6-7-8 hours-cancel. Once the selected time has elapsed, the fireplace will turn off. (default) Ambience Setting The Ambience Setting button will open up a second window where customizations can be performed, including temperature scale setting (C/F), Weekly/Heat programming,...
  • Page 24 WI-FI REMOTE Power Off Turn On Cancel HEAT PROGRAM SUB MENU CONTINUED Heat > Power Level Sets fireplace status (no heat) OFF/ON. Off > Heat Level Sets Heat Level: OFF/LOW/HIGH. High > Temperature Temperature Level for the heater to turn on if the ambient temperature falls below the set temperature (High Heat.)
  • Page 25 WI-FI REMOTE > Mode Color Mode color: In the Static mode, only one color can be selected. After clicking the color symbol, you can change to additional colors. When using the Jump/Gradient feature, 8 colors can be programmed by clicking “+” color. By adjusting the color sliders, select the corresponding RGB value to obtain the desired color combination..
  • Page 26 WI-FI INITIAL LOG-IN Search for and install the “MODERN FLAMES” app from Google Play or Apple App store or scan the QR code. STEP STEP > After Download & Installed Login to Modern Flames app. > App Example...
  • Page 27 WI-FI PAIRING STEP STEP > Once Opened and Logged In > Select Fireplace From the home page, select the add “+” Select series of fireplace that will be symbol. pairing too and follow instructions.
  • Page 28: Wifi Information

    WI-FI REMOTE STEP STEP > WiFi Information > Ensure Fireplace is ON If pairing via Wi-Fi you must use 2.4 GHz Using the fireplace manual touch Wi-Fi, and must have information filled controls, turn ON the fireplace. out to move to next step.
  • Page 29 WI-FI REMOTE STEP STEP > Place Fireplace in Pairing Mode > Wi-Fi Pairing Confirmed Once fireplace is “ON”, place fireplace in EZ pairing mode is confirmed with a single audible beeping tone is heard and Wi-Fi pairing mode following the all the lights begin to blink rapidly instructions for pairing mode on the APP.
  • Page 30 WI-FI REMOTE STEP STEP > Pairing > Device Paired Successfully NOTE: Do not turn off or disconnect the Device & APP should now begin to pair. Depending on Wi-Fi this can take up the fireplace from power while pairing the Wi-Fi or performing updates.
  • Page 31: Maintenance

    MAINTENANCE...
  • Page 32: Troubleshooting

    TROUBLE SHOOTING PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION A. Breaker tripped or circuit has no A. Reset breaker, test circuit for power, check power power switch B. Internal component is frozen B. Turn power off at the main breaker for 60 Nothing comes on and needs to be reset seconds.
  • Page 33: Frequently Asked Questions

    Q. How do I reset the unit? A. Turn power off at the breaker for 1 minute. Q. How do I install the Optional Wall Mount Touch Control and Wi-Fi App? A. Optional wall control & Wi-Fi app instructions available for download on Modern Flames’ website...
  • Page 34: Fcc Caution

    FCC CAUTION This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
  • Page 35 NOTES __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________...
  • Page 36 Copyright © 2024 RPG Brands (Modern Flames). All rights reserved. Products and specifications subject to change without notice. The product images shown are for illustration purposes only and may not be an exact representation of the product. 022024...

Table of Contents