Program Virtual Limit Sensors - Max 1700FS Quick Install Manual

6

program virtual limit sensors

Gate operator OPEN and CLOSE buttons are disabled until virtual limits have been programmed.
If OPEN or CLOSE buttons are pressed and programming has not been done, Operator will beep and nothing will happen.
1. Erase Current Virtual Limits
PRECAUTION to ensure removal of previous limit settings (NO factory setting):
• Press and hold the STOP button while simultaneously pressing the
CLOSE button.
• Hold BOTH buttons down until a beep is heard (approx. 5 sec).
• Release buttons. Both virtual OPEN and CLOSE limits have been erased.
2. Program Virtual CLOSE Limit
• Press and hold the POSITION RECORDER button while simultaneously
pressing the CLOSE button.
• Hold BOTH buttons down until POSITION RECORDER LED and GATE STATUS
CLOSE LED start flashing and beeping begins.
• While beeping, press CLOSE button again to move the gate to the general close
position. Use the jog switches on the MC-200 to adjust gate to the final gate
close position as desired.
PhotoCell Edge Limit SW
2
POWER 1
Edge
UL MATRIX
MC-200 ON-LINE
Entrap
Motor Controller
• After the final close position is chosen, press the POSITION RECORDER button again to record the current gate position as the virtual CLOSE limit.
The POSITION RECORDER LED will turn OFF, the GATE STATUS CLOSE LED will turn ON and stay on and the beeping will stop.
Virtual CLOSE limit is programmed.
3. Program Virtual OPEN Limit
• Press and hold the POSITION RECORDER button while simultaneously
pressing the OPEN button.
• Hold BOTH buttons down until POSITION RECORDER LED and GATE STATUS
OPEN LED start flashing and beeping begins.
• While beeping, press OPEN button again to move the gate to the general open
position. Use the jog switches on the MC-200 to adjust gate to the final gate
open position as desired.
PhotoCell Edge Limit SW
2
1
POWER
Edge
UL MATRIX
MC-200 Entrap ON-LINE
Motor Controller
• After the final open position is chosen, press the POSITION RECORDER button again to record the current gate position as the virtual OPEN limit.
The POSITION RECORDER LED will turn OFF, the GATE STATUS OPEN LED will turn ON and stay on and the beeping will stop.
Virtual OPEN limit is programmed. Push CLOSE button and the operator will function normally.
15 14 13
16 12
MAX
ERD
LED ON
3
Motor
4
5
JOG
JOG
OverLoad
LEFT RIGHT
ERD
Sensitivity
15 14 13
16
12
MAX
ERD
LED ON
3
Motor
4
5
JOG JOG
OverLoad
LEFT RIGHT
ERD
Sensitivity
MATRIX 1
BATTERY
BACK-UP MODE
LEAVE
CLOSED
MADE in USA LEAVE OPEN
OPEN 1 TIME
AUTOMATIC OPEN/CLOSE CONTROLS
ANTI
EXIT
TAILGATE
EXIT
ON OFF
CENTER
SAFETY
MIN MAX
OFF
CLOSE TIMER
PARTIAL
OPEN
ID
PLUG
POSITION
RECORDER
12VDC
GND
OBD PORT
BLACK BOX
24VDC
MAX
GND
MATRIX 1
BATTERY
BACK-UP MODE
LEAVE
CLOSED
MADE in USA LEAVE OPEN
OPEN 1 TIME
AUTOMATIC OPEN/CLOSE CONTROLS
ANTI
EXIT
TAILGATE
EXIT
ON OFF
CENTER
SAFETY
MIN MAX
OFF
Position Recorder LED
CLOSE TIMER
PARTIAL
OPEN
ID
PLUG
POSITION
RECORDER
12VDC
GND OBD PORT
BLACK BOX
24VDC
MAX
GND
Press Together
MATRIX 1
BATTERY
BACK-UP MODE
LEAVE
CLOSED
LEAVE OPEN
MADE in USA
OPEN 1 TIME
AUTOMATIC OPEN/CLOSE CONTROLS
ANTI
EXIT
TAILGATE
EXIT
ON OFF
CENTER
SAFETY
MIN MAX
OFF
Position Recorder LED
CLOSE TIMER
PARTIAL
OPEN
ID
PLUG
POSITION
RECORDER
12VDC
GND OBD PORT
BLACK BOX
24VDC
MAX
GND
Press
Together
5
PRIMARY
GATE
MAGLOCK
DELAY
OPEN OPEN
MAG
LEFT RIGHT
OFF 1.5Sec 2Sec LOCK
COM
NC
Tamper NO
CENTER SAFETY GATE
COM
TAMPER
GND
Tamper IN
PHOTOCELL
UL
EDGE 1
EDGE 2
ENTRAP
ID PLUG
MOTOR MOTION ERROR
UL ALARM 12V
ALARM RET
STOP CLOSE
RESET
OPEN
GND
MAX
REVERSE SENSITIVITY
GATE SPEED
MOTOR OVERLOAD
OPEN
GATE
MIN
NO LIMIT SWITCH /
COM
STATUS
CLAMP SLIPPING
CLOSE
Press
LIMIT
BATTERY
Together
SWITCH
IN USE
ON-LINE
PRIMARY
GATE
MOTOR
POWER
ON-LINE
MAGLOCK
DELAY
PRIMARY SEC
OPEN OPEN
MAG
GATE GATE
LEFT RIGHT
OFF 1.5Sec 2Sec LOCK
COM
NC
Tamper NO
CENTER SAFETY GATE
COM
TAMPER
GND
Tamper IN
PHOTOCELL
UL
EDGE 1
ENTRAP Gate Status CLOSE LED EDGE 2
ID PLUG
MOTOR MOTION ERROR
UL ALARM 12V
ALARM RET
CLOSE
RESET
OPEN STOP
GND
MAX
REVERSE SENSITIVITY
GATE SPEED
MOTOR OVERLOAD
OPEN
GATE
MIN
NO LIMIT SWITCH /
COM
STATUS US S S S S S S S
CLAMP SLIPPING
CLOSE
LIMIT
BATTERY
SWITCH
IN USE
ON-LINE
MOTOR
POWER
ON-LINE
PRIMARY SEC
GATE GATE
PRIMARY
GATE
MAGLOCK
DELAY
OPEN OPEN MAG
LEFT RIGHT
OFF 1.5Sec 2Sec
LOCK
COM
NC
Tamper NO
CENTER SAFETY GATE
COM
TAMPER
GND
Tamper IN
PHOTOCELL
UL
EDGE 1
ENTRAP EDGE 2
Gate Status OPEN LED
ID PLUG
MOTOR MOTION
ERROR
UL ALARM 12V
ALARM RET
OPEN
RESET
STOP CLOSE
GND
MAX REVERSE SENSITIVITY
GATE SPEED
MOTOR OVERLOAD
OPEN
GATE E E E
MIN
NO LIMIT SWITCH /
STATUS S S COM
CLAMP SLIPPING
CLOSE
LIMIT
BATTERY
SWITCH
IN USE
ON-LINE
MOTOR
POWER
ON-LINE
PRIMARY SEC
GATE GATE
UL 325 2016 Standard-MAX 1700FS Quick Install Rev 3