Max 1700FS Quick Install Manual page 23

miller gate link
Example: Input 3 is
NOT used and MUST
be jumpered to GND.
r
l l e
t r o
l l e r
o n
t r o
r C o n
d .
r c
u s e
o t o
o t o
a r e
Y m
X M
r s
A R
a t o
M A
p e r
R I M
a l o
e P
U s
d u
e n
w h
P h
o to
P O
C e
W E ll E
M C d g
R e
L im
- 2 0
M o it S
2
W
t o r 0
U L
C o
E n 1
n t r
tr a E d
p
o ll g e
e r
M A
O N T R
IX
- L IN
E
J O
M A
G
L E X
L E
F T J O D O
1 6 1 5 1
N
G
R I
G H
T
3
4
E R
S e
n s
Antenna Mount
CH 1 CH 2
LEARN
P
R 1 2
MGL-RX20
Monitored Gate Link
MillerEdge
MGL-RX20 Receiver
Installation Steps:
1. Set Both DIP-switches to "R" on receiver
2. Wire 12V power to receiver, polarity does not matter
3. Wire motor controller EDGE 1 to receiver CH 1-P/N.C.
Wire motor controller GND to receiver CH 1-COM
4. Wire motor controller EDGE 2 to receiver CH 2-P/N.C.
Wire motor controller GND to receiver CH 2 - COM
5. Install antenna on receiver
6. Install batteries in transmitters
7. Wire Channel 1 Transmitter to CLOSING Edge ONLY
8. Wire Channel 2 Transmitter to OPENING Edge
9. Program Channel 1 and 2 on MGL-RX20 receiver
10. Program MAX motor controller to "LEARN" Edge 2
NOTE: Edge 2 will function without being "Learned" but will NOT be
MONITORED by the MAX gate operator.
See your chosen Max operator manual to program the MAX motor
controller to "Learn" Edge 2 if desired.
Jumper UNUSED Entrapment
Protection Inputs or a fault
will occur.
Sensor
Wires
1
2
3
0
- 2 0
M C
4
1 3
1 2
E R To PWR 12V and GND
5
D
D M o
O v
it iv t o r
it y e r L
o a Polarity does NOT matter.
d
NOTE:
Edge 1 - CLOSING direction ONLY
Edge 1 is automatically MONITORED.
Edge 2 - "Learned" Open/Close direction
See installation steps #10 note below.
CLOSING 10K sensing edge
connected to Channel 1 (Edge 1).
OPENING 10K sensing edge
connected to Channel 2 (Edge 2).
Channel 1 & 2 transmitters MUST be
programmed by receiver. See below and
Miller Edge Gate Link MGL-K20
instruction sheet for more info.
Both DIP-switches (Channel 1 & 2) to "R"
DO NOT set to "P" Pulsed
2 Channel Wireless Communication
IMPORTANT: Receiver
MUST be powered by MAX
Motor Controller or it will
NOT be MONITORED.
Wire 10K Edges
Gate Link Receiver/Transmitter Programming:
1. Make sure receiver and transmitters have power.
2. Green power LED stays ON; CH 1 red LED will be blinking on
receiver.
3. To enter Learn mode, press the CH 1 Learn button for 1 sec.
The red led remains ON and the amber status LED will blink.
4. Activate the transmitting edge, the red and amber LEDs will
alternately blink rapidly on receiver. Then the red LED will go out
and the amber LED will remain ON.
5. Channel 1 is now programmed. Repeat steps for Channel 2.
6. To start over or erase programming, press and hold both
LEARN buttons for 3 seconds. The LEDs will blink rapidly and
then go into "fault" mode. Repeat the programming steps above.
21
MGL-TX20
Transmitter
MGL-TX20
Test Button
Green LED
M G
L - T An MGL-TX20 transmitter is
M o
X 2
n i t 0
o r e
G a
t e d
L i n
k
needed for each channel of
the receiver.
M i
l l e
r E d
g e
A GEM-104 module is NOT
needed for the sensing edge
when using a gate link
Mount on Gate's
transmitter.
CLOSING side.
UL 325 2016 Standard-MAX 1700FS Quick Install Rev 3
S e
c o n
d t
s o l
r a n
d s
s m
e p
a r a i t t e
r
t e l
y
T r a
n s m
i t t e
r
v e r
c e i
R e
Terminal Block
Connection
Polarity does
NOT matter.
M G
L - T
M o
X 2
n i t 0
o r e
G a
t e
d
L i n
k
M i
l l e
r E d
g e
Mount on Gate's
OPENING side.