Max 1700FS Quick Install Manual page 17

matrix 1 led continued
1. EXIT LOOP
2. CENTER LOOP
3. SAFETY LOOP
ID plug MUST be plugged in.
4. 12 VDC
5. 24 VDC
6. SECONDARY LIMIT SWITCH ON-LINE
7. PRIMARY LIMIT SWITCH ON-LINE
Matrix 1 LED
Problem Condition
"PHOTOCELL" LED is ON
"PHOTOCELL" LED is FLASHING
"MOTOR OVERLOAD" LED is ON
"NO LIMIT SW / CLAMP SLIPPING" LED is ON
"EXIT" LOOP LED is FLASHING or
contstantly ON
"SAFETY" LOOP LED is FLASHING or
contstantly ON
"GATE DISABLE" LED is ON
"MAG LOCK" LED is FLASHING
"GATE TAMPER" LED is FLASHING
"12VDC" LED is OFF. "24VDC" LED is OFF
MATRIX 1
BATTERY
BACK-UP MODE
LEAVE
CLOSED
MADE in USA LEAVE
OPEN
AUTOMATIC OPEN/CLOSE CONTROLS
ANTI
TAILGATE
EXIT
ON OFF
CENTER
SAFETY
MIN MAX
OFF
CLOSE TIMER
PARTIAL
OPEN
ID
PLUG
POSITION
MAX 1700FS
RECORDER
12VDC
GND OBD PORT
BLACK BOX
24VDC
GND
Normal
LED
OFF • Jumper between PHOTOCELL and GND is missing or broken (jumper is required if a sensor is not
12
present).
• Sensor on PHOTOCELL input (photocell or edge) may have detected an obstruction while opening or
closing gate.
OFF • Photocell on PHOTOCELL input is misaligned with reflector.
12
• Sensor on PHOTOCELL input (photocell or edge) may not be wired properly, (see
• Sensor is NOT a N.C. monitored sensor that is UL325 2016 compliant.
• Sensor on PHOTOCELL is damaged or malfunctioning.
OFF • Sensor might need to be re-learned.
18
• Check if gate is binding against catch post or bracket in opened or closed position.
• Check if gate moves manually with low resistance throughout its full range of motion.
• Check if chain is installed inline with idle wheels in both OPEN and CLOSED positions.
OFF • Gate may be too heavy for operator (check manual for maximum gate capacity).
19
• Check if OPEN and CLOSE magnets are still connected on chain.
OFF • Loop fault condition: Check if EXIT loop wires are connected into to loop input connector properly.
1
• Check if loop detector is inserted properly in Matrix 1 slot.
• Set unique loop detector frequency for each loop detector used.
• Loop Detector might be defective. Replace defective loop detector.
NOTE: RENO loop detector LED's flash as default, but function normally (ignore the flashing).
OFF • Loop fault condition: check if SAFETY loop wires are connected into to loop input connector properly.
3
• Check if SAFETY loops are wired in series.
• Check if loop detector is inserted properly in Matrix 1 slot.
• Set unique loop detector frequency for each loop detector used.
• Loop Detector might be defective. Replace defective loop detector.
NOTE: RENO loop detector LED's flash as default, but function normally (ignore the flashing).
OFF • Check if "Gate Shut-off" switch is ON, Turn it OFF. If it is OFF, cycle the switch (ON then OFF).
22
• Check if the chain is dropped. If so, gate is disabled for safety. Re-install chain and cycle the "Gate
Shut-off" switch (ON then OFF) to enable operator.
• Check if an external device is triggering GATE DISABLE input on Matrix 1. Disconnect devices
individually to determine possible false triggering of GATE DISABLE.
OFF • Maglock power is lost. Check if maglock power transformer is wired properly to Matrix 1 or needs to be
10
replaced.
• Switch is set to delay but no maglock is connected. Set switch to OFF
OFF • Gate was manually moved off of its CLOSED position causing Tamper Relay to trigger for few seconds.
11
ON • Check for a short in wiring to connected device. DO NOT power external keypads or telephone entry to
4 or 5
this port (only use for radio receiver / photocell).
PRIMARY
GATE
MAGLOCK
DELAY
OPEN OPEN
OPEN MAG
LEFT RIGHT
1 TIME
OFF 1.5Sec 2Sec
LOCK
Tamper NO
GATE
EXIT CENTER SAFETY
TAMPER
Tamper IN
PHOTOCELL
UL
ENTRAP
ID PLUG
MOTOR MOTION
UL ALARM 12V
ALARM RET
OPEN STOP CLOSE
MAX REVERSE SENSITIVITY
GATE SPEED
MOTOR OVERLOAD
GATE
MIN
NO LIMIT SWITCH /
STATUS
CLAMP SLIPPING
MAX
LIMIT
SWITCH
ON-LINE
MOTOR
ON-LINE
PRIMARY SEC
GATE GATE
8. SECONDARY MOTOR ON-LINE
9. PRIMARY MOTOR ON-LINE
Solution(s) for
Problem Condition
15
COM 10. MAGLOCK
NC
11. GATE TAMPER
COM
GND
12. PHOTOCELL
13. EDGE 1
EDGE 1
14. EDGE 2
EDGE 2
15. ID PLUG ERROR
ERROR
16. UL ENTRAPMENT
RESET
GND
17. REVERSE SENSITIVITY
18. MOTOR OVERLOAD
OPEN
19. NO LIMIT SWITCH
COM
CLOSE
CLAMP SLIPPING
20. BATTERY IN USE
BATTERY
IN USE
21. POWER
POWER
22. GATE DISABLE
UL 325 2016 Standard-MAX 1700FS Quick Install Rev 3
).
7