Max 1700FS Quick Install Manual page 22

emx irb-mon
Transmitter
To Motor Controller
(TX)
PWR 24V Input
Secondary
Operator
NO Matrix 1
Transmitter (TX)
TX
Green
POWER INPUT
LED
TRANSMITTER
BOARD (TX)
DO NOT wire Transmitter
(TX) to Secondary Motor
Controller PWR 12V!
MOTOR BATTERY
MOTOR Power In
INPUTS PACK
ONLY power entrapment protection
2 3
Inputs & MUST be "LEARNED"
sensors with MC-200 PWR 12V
to MONITOR sensors.
To LEARN inputs 2 & 3 :
1. MONITORED Sensors MUST be
wired to inputs BEFORE they can be
learned. Any unused inputs MUST be
jumpered.
2. Reversing Edge and/or Photo Cell can
be wired to either input 2 or 3.
3. Press and HOLD the OPEN & STOP
buttons at the same time on Matrix 1
until beep is heard, learn mode begins.
MOTOR MOTION
OPEN STOP
CLOSE
Learn mode lasts for 5 min. indicated
by beeping.
4. LEDs WILL be ON for each detected
sensor on MC-200. LEDs WILL be ON
for BOTH MC-200s when dual
operators are used.
5. Press STOP button again within 5 min.
to learn sensors and end learn mode,
beeping stops.
Inputs are now MONITORED.
Entrapment Protection
Inputs:
MUST jumper
unused inputs 1
3 2
SECONDARY
Motor Controller
NOTE: To meet the UL 325 2016 standard, Type B1 Non-Contact sensor
entrapment protection device MUST be MONITORED by the gate operator.
Photocell (Thru-Beam) CLOSING Direction
Dual Gate Operators
Entrapment Area
CLOSING direction Thru-Beam EMX IRB-MON Photocell
T X
Installation Steps:
1. Set DIP-switches on receiver.
2. Install jumper on receiver.
3. Wire 12V Primary motor controller
power to receiver.
4. Wire Primary motor controller
EDGE 1 to receiver photocell NC.
Wire Primary motor controller GND
to receiver photocell COM.
5. Wire 24V Secondary motor
controller power to transmitter.
6. Align photocells.
7. Adjust sensitivity on receiver.
IMPORTANT: Photocells MUST
be powered by Motor Controllers
or they will NOT be MONITORED.
PWR 24V
Polarity does NOT matter
LIMIT ALARM
SWITCH
MATRIX 1
MC-200 PWR 12V MUST be used
Entrapment Protection
Sensor Guidelines
•
A sensor MUST be wired to EDGE 1 or
operator WILL NOT function.
Monitored
•
Wire NORMALLY CLOSED (N.C.)
Reversing
MONITORED sensors ONLY, to each
Edge
operator's MC-200 when dual operators
OR are used.
•
Reversing Edge and/or Photo Cell can
Monitored
be wired to ANY of the 3 Inputs.
Photo
•
Cell MC-200 PWR 12V MUST be used to
power MONITORED sensors.
• UNUSED inputs MUST remain
JUMPERED or fault will occur.
CAUTION: See installation instructions.
ATTENTION:
Voir la notice d'installation.
Jumper ALL Entrapment
Protection Inputs to GND.
CLOSING direction Photocell
Gates Closed
IMPORTANT:
Photocells MUST be
in alignment or fault will occur.
Green LED will remain ON receiver
when in proper alignment.
Sensitivity Adjustment:
If the IRB-MON does not
respond to an obstruction,
lower the sensitivity by
turning adjustment
counter-clockwise.
DIP-switches:
1, 2, 3 are OFF.
Switch 4 is ON
If trouble occurs, try
turning switch 4 OFF.
NOTE: Power must be
cycled when switches
are changed.
Jumper MUST be on Com-NC.
N O
MOTOR Power In
2 3
Inputs & MUST be "LEARNED"
to MONITOR sensors.
To LEARN inputs 2 & 3 :
1. MONITORED Sensors MUST be
wired to inputs BEFORE they can be
learned. Any unused inputs MUST be
jumpered.
2. Reversing Edge and/or Photo Cell can
be wired to either input 2 or 3.
3. Press and HOLD the OPEN & STOP
buttons at the same time on Matrix 1
until beep is heard, learn mode begins.
MOTOR MOTION
OPEN STOP
CLOSE
Learn mode lasts for 5 min. indicated
by beeping.
4. LEDs WILL be ON for each detected
sensor on MC-200. LEDs WILL be ON
for BOTH MC-200s when dual
operators are used.
5. Press STOP button again within 5 min.
to learn sensors and end learn mode,
beeping stops.
Inputs are now MONITORED.
Entrapment Protection
Inputs:
MUST jumper
unused inputs
PRIMARY
Motor Controller
Jumper UNUSED Entrapment
Protection Inputs to GND or
a fault will occur.
20
Receiver
To Motor Controller
(RX)
EDGE 1 and PWR 12V Input
Primary
Operator
Matrix 1
Receiver (RX)
RX
NO COM NC
NC COM NO POWER
INPUT
JUMPER
C o
RECEIVER
m N
BOARD (RX)
C
Normally Closed
PWR 12V
Polarity does NOT matter
MOTOR BATTERY LIMIT ALARM
INPUTS PACK SWITCH
ONLY power entrapment protection
sensors with MC-200 PWR 12V
MC-200 PWR 12V MUST be used
Entrapment Protection
Sensor Guidelines
•
A sensor MUST be wired to
operator WILL NOT function.
Monitored
•
Wire NORMALLY CLOSED (N.C.)
Reversing
MONITORED sensors ONLY, to each
Edge
operator's MC-200 when dual operators
OR are used.
•
Reversing Edge and/or Photo Cell can
Monitored
be wired to ANY of the 3 Inputs.
Photo
•
Cell MC-200 PWR 12V MUST be used to
power MONITORED sensors.
• UNUSED inputs MUST remain
JUMPERED or fault will occur.
CAUTION: See installation instructions.
ATTENTION:
Voir la notice d'installation.
1
3 2
UL 325 2016 Standard-MAX 1700FS Quick Install Rev 3
Green
LED
SENSITIVITY
EARTH
GND
Common-GND
Edge 1
MATRIX 1
EDGE 1 or