Parts Identification Not actual size METAL TUBE Q'ty: 1 METAL TUBE Q'ty: 1 SLAT METAL TUBE SUPPORT LEGS Q'ty: 12 Q'ty: 1 Q'ty: 22 FOOTBOARD LEG-LEFT FOOTBOARD LEG-RIGHT Q'ty: 1 Q'ty: 1...
Page 4
Parts Identification SIDE RAIL-3 FOOTBOARD Q'ty: 1 Q'ty: 1 SIDE RAIL-4 FOOTBOARD CONNECTER-UPPER FOOTBOARD CONNECTER-LOWER Q'ty: 1 Q'ty: 1 Q'ty: 1 hole BOTTOM TUBE SHELF PANEL RIGHT SIDE PANEL Q'ty:1 Q'ty: 1 Q'ty: 1 SHELF PANEL LEFT SIDE PANEL BACK PANEL Q'ty: 1 Q'ty: 1 Q'ty: 1...
Hardware List Ø1/4" x 12mm M8 x 13mm M8 x 25mm Ø1/4" x 16mm x 18 x 16 BOLT BOLT BOLT spare: 1 spare: 2 spare: 1 Ø1/4" x 25mm Ø1/4" x 35mm Ø1/4" x 50mm Ø3.5 x 15mm x 14 BOLT BOLT BOLT...
Page 6
MODE SPEED DEMO SPEED MODE COLOR BRIGHT COLOR BRIGHT RF Wireless 6/19...
Page 7
Parts Identification Not actual size 7/19...
Page 10
STEP 5 Ø3.5 x 15mm BACK SIDE(the side with holes) Note the switch is on this side,not the right side. THE 2 ENDS OF LED STRIP MUST TO BE REINFORCED BY LED STRIP CLIPS Stick LED strip underneath board , then put the clips on LED strip and fasten it with screws to reinforce the LED strip.
Page 11
STEP 7 Ø3 x 38mm Ø3 x 38mm STEP 8 x 12 11/19...
Page 12
STEP 9 x 12 STEP 10 Ø3.5 x 15mm Connect lamp strip usb, usb adapter and socket . Then buckle the lines using wire clip To avoid cable clutter,you can clamp the LED STRIP cable and socket cable with cable clip ⑰...
Page 13
Ø1/4" x 50mm Ø1/4" x 50mm Ø1/4" x 16mm Ø1/4" x 16mm Before you install this bolt, please make sure the bolt size is Ø1/4"*16mm.
Page 14
Ø1/4" x 12mm Ø1/4" x 12mm Before you install this bolt, please make sure the bolt size is Ø1/4"*12mm.
Page 15
STEP 15 Please tighten the screws to 80% first, and tighten all screws 100% after all Ø1/4" x 16mm parts are assembled. STEP 16 Please tighten the screws to 80% first, and tighten all screws 100% after all M8 x 13mm M8 x 25mm parts are assembled.
Page 16
STEP 17 STEP 18 Ø1/4" x 12mm Ø1/4" x 12mm Before you install this bolt, please make sure the bolt size is Ø1/4"*12mm. 16/19...
Page 17
STEP 19 STEP 20 Please tighten the screws to 80% first, and tighten all screws 100% after all Ø1/4" x 35mm Ø1/4" x 12mm parts are assembled. Ø1/4" x 35mm Before you install this bolt, please make sure the bolt size is Ø1/4"*35mm.
Page 18
STEP 21 Ø1/4" x 25mm Ø1/4" x 25mm Before you install this bolt, please make sure the bolt size is Ø1/4"*25mm. STEP 22 Please tighten the screws to 80% first, and tighten all screws 100% after all parts are assembled. M8 x 13mm Ø1/4"...
Page 19
STEP 23 x 24 K x 12 Assemble the slats 3.Put the plastic clamp(9) into the 4.Press tight the upper part of lower part of hole on 45 degree. clamp to fix its position. 19/19...