Page 1
J9P004BS0M There are two installation options,you can chose. As this item contains many parts, please read the installation instruction carefully before installation and complete the installation with the cooperation of your partner. Please use tools properly and carefully. If you have any questions about the product and installation, please contact us.
Before You Start Read through each step carefully and follow the proper order Separate and count all your parts and hardware Give yourself enough room for the assembly process Have the following tools: Flat Head Screwdriver, #2 Phillips Head Screwdriver and Hammer Caution: If using a power drill or power screwdriver for screwing, please be aware of to slow down and stop when screw is tight.
Board Identification Not actual size RIGHT SIDE PANEL LEFT SIDE PANEL Qty:1 Qty:1 Qty:1 PARTITION FRONT SLAT BACK SLAT Qty:1 Qty:1 Qty:1 REAR LOWER PANEL FIXED SHELF UPPER LEFT PANEL Qty:1 Qty:2 Qty:1 3-48...
Page 4
Board Identification Not actual size UPPER RIGHT BACK PANEL DRESSING MIRROR LEFT DRAWER FRONT Qty:1 Qty:1 Qty:1 LEFT DRAWER SIDE RIGHT DRAWER FRONT DRAWER BACK PANEL Qty:2 Qty:1 Qty:2 RIGHT DRAWER SIDE DRAWER BOTTOM SPONGE CUSHION Qty:2 Qty:2 Qty:1 4-48...
Page 5
Board Identification Not actual size STOOL UP APRON STOOL SIDE PANEL BACK SLAT Qty:2 Qty:2 Qty:1 LEFT SIDE PANEL CABINET LEFT SIDE PANEL RIGHT SIDE PANEL Qty:1 Qty:1 Qty:1 CABINET BACK SLAT BOTTOM FRONT RAIL CABINET FRONT SLAT QTY:1 Qty:1 Qty:1 5-48...
Page 6
Board Identification UPPER FIXED SHELF UPPER RIGHT SIDE PANEL UPPER LEFT SIDE PANEL Qty:1 Qty:1 Qty:1 DRESSING MIRROR MIDDLE FIXED SHELF UPPER BACK PANEL Qty:1 Qty:2 Qty:1 DRAWER FRONT DRAWER BACK PANEL LOWER BACK PANEL Qty:3 Qty:3 Qty:1 6-48...
Page 7
Board Identification RIGHT DRAWER SIDE DRAWER BOTTOM LEFT DRAWER SIDE Qty:3 Qty:3 Qty:3 7-48...
Page 8
Board Identification Not actual size 8-48...
Part List Ø15X9.5mm Ø6.5X35mm Ø8X30mm Ø6X30mm CAM LOCK CAM BOLT WOODEN DOWEL WOODEN DOWEL spare:3 spare:3 spare:2 Ø6.3X50mm Ø4X35mm Ø4X19mm Ø3X14mm SCREW SCREW SCREW SCREW spare:2 spare:1 spare:1 Ø4X14mm Ø3X12mm Ø3.5X14mm 60X38X1.3mm PIECES OF IRON SCREW SCREW SHELF SUPPORT spare:1 spare:1 spare:3 Ø17XØ24X20...
Page 10
Part List 14" 14" 14" 14" 350mm 350mm 350mm 300mm 20DL 20DR 20CR 21CL RIGHT CABINET MEMBER LEFT DRAWER RUNNER RIGHT DRAWER RUNNER LEFT CABINET MEMBER 14" 14" 14" 300mm 300mm 300mm 21CR 21DL 21DR LEFT DRAWER RUNNER RIGHT CABINET MEMBER RIGHT DRAWER RUNNER PERFECT STICKER spare:1...
Page 11
STEP1 Ø8X30mm Ø6.5X35mm THE RIGHT DIRECTION FINISH No. 23 hardware completion direction Ø8X30mm 11-48...
Page 13
STEP3 Ø15X9.5mm EDGE BANDING Insert the cam bolt into the hole first, then insert the cam lock and lock it. Proper orientation of CAM LOCK 13-48...
Page 17
STEP7 Ø8X30mm Ø15X9.5mm Ø6.5X35mm Insert the cam bolt into the hole first, then insert the cam lock and lock it. Proper orientation of CAM LOCK 17-48...
Page 18
STEP8 Ø15X9.5mm HOLES Insert the cam bolt into the hole first, then insert the cam lock and lock it. Proper orientation of CAM LOCK 18-48...
Page 19
STEP9 Ø15X9.5mm Insert the cam bolt into the hole first, then insert the cam lock and lock it. Proper orientation of CAM LOCK 19-48...
Page 20
STEP10 Ø15X9.5mm Insert the cam bolt into the hole first, then insert the cam lock and lock it. Proper orientation of CAM LOCK 20-48...
Page 21
STEP11 Ø3X14mm 90° 90° Before attaching the back panel, be sure that the unit is at 90°. 21-48...
Page 22
STEP12 Ø15X9.5mm Ø6X35mm Ø4X35mm Step 1 Step 2 Step 3 Insert the cam bolt into the hole first, then insert the cam lock and lock it. Proper orientation of CAM LOCK 22-48...
Page 26
STEP16 THIS STEP REQUIRES 2 PEOPLE Ø3.5X14mm Pre-drilled Locked with panel Pre-drilled. After you adjustable the gap, You can Locked the other three screws. The FF plate is lifted up as much as possible, and the No. 11 hardware hole position and the MM plate hole position are aligned, otherwise the FF plate will sink.
Page 27
STEP17 To adjust the vertical height. Loosen the four screws "A" on both hinges. Two of them are usually in slotted holes which allows you to adjust up or down by a few mm. Then tighten back up. To adjust depth. Loosen screw "B"...
Page 43
STEP33 Ø15X9.5mm Ø6.5X35mm Insert the cam bolt into the hole first, then insert the cam lock and lock it. Proper orientation of CAM LOCK 43-48...
STEP37 When making upcan use the switch to turn on or off the light. the dressing table brings you 3temperature light modes, touch the button you can easy light up the mirror and changeet your different needs, long press to adjust the brightness TOUCH SWITCH 47-48...
Page 48
STEP38 NOTE :The tipping restraint hardware included is for wooden stud wall construction. It must be attached to a wall stud. Depending upon your wall construction different anchor hardware maybe required. Please contact your local hardware store for assistance. Young children can be X2set seriously injured by tipping furniture.