Page 1
WhatsApp community↑ J3L106BS01 As this item contains many parts, please read the installation instruction carefully before installation . Please use tools properly and carefully. If you have any questions about the product and installation, please contact us. service@vabchesofficial.com Our professional after-sales team will serve you online all day.
Before You Start Read through each step carefully and follow the proper order Separate and count all your parts and hardware Give yourself enough room for the assembly process Have the following tools: Flat Head Screwdriver, #2 Phillips Head Screwdriver and Hammer Caution: If using a power drill or power screwdriver for screwing, please be aware of to slow down and stop when screw is tight.
Board Identification Not actual size DESK TOP LEFT SIDE PANEL RIGHT SIDE PANEL Qty:1 Qty:1 Qty:1 PARTITION UPPER LEFT SIDE PANEL UPPER PARTITION Qty:1 Qty:1 Qty:1 UPPER RIGHT SIDE PANEL FIXED SHELF RAIL Qty:1 Qty:2 Qty:2 RAIL RAIL LEFT FRONT CROSS MEMBER Qty:1 Qty:1 Qty:1...
Page 4
Board Identification Not actual size LOWER LEFT REAR RAIL LEFT REAR PANEL RIGHT FRONT SIDE MEMBER Qty:1 Qty:1 Qty:2 RIGHT BACK RAIL RIGHT FRONT RAIL BOTTOM FRONT RAIL Qty:1 Qty:1 Qty:1 LARGE DRAWER FRONT DRAWER LEFT PANEL DRAWER RIGHT PANEL Qty:1 Qty:1 Qty:1...
Page 5
Board Identification Not actual size SMALL DRAWER FRONT DRAWER LEFT PANEL DRAWER RIGHT PANEL Qty:3 Qty:3 Qty:3 DRAWER BACK PANEL BOTTOM OF DRAWER LOWER RIGHT REAR PANEL Qty:3 Qty:3 Qty:1 FIXED SHELF UPPER RIGHT BACK PANEL FIXED SHELF Qty:2 Qty:1 Qty:2 LOWER BACK UPPER BACK PANEL...
Page 7
Part List 14'' 14'' 14'' 14'' 350mm 350mm 350mm 350mm 13CL 13CR 13DL 13DR LEFT CABINET MEMBER RIGHT CABINET MEMBER LEFT DRAWER RUNNER RIGHT DRAWER RUNNER 4X65mm PLUG BOARD HAIR DRYER RACK THE POWER PLUG HEX KEY Ø21mm X1 set ANTI-TIPPING HARDWARE HOLE STICKER apare:2...
Page 8
Board Identification Not actual size 8-39...
Page 18
STEP10 Ø15X11mm Without Edge Banding Proper orientation of CAM LOCK 18-39...
Page 19
STEP11 Ø3X14mm Before attaching the back panel, be sure that the unit is at 90°. 19-39...
Page 20
STEP12 WARNING How To SEPARATE BALL BEARING SLIDE. Pull toward arrow to open the slide until its stops and then flip it over. 2) Push plastic lever down and pull apart. Cabinet member Drawer member 20-39...
Page 21
STEP13 18'' 450mm Ø4X14mm Ø21mm Paste the hole sticker at the place marked by the Mounting Holes circle 21-39...
Page 33
STEP25 Ø3X14mm Ø4X14mm You can install the hair dryer rack(15) on the left or right according to your needs Before attaching the back panel, be sure that the unit is at 90°. 33-39...
Page 34
STEP26 Ø4X14mm 450mm Open end Mounting Holes Before assembly, take out the power connector inside the hole. Open end Open end 34-39...
Page 35
STEP27 Ball bearing cart Ball bearing cart Please complete this step with the cooperation of two people 35-39...
STEP30 When making upcan use the switch to turn on or off the light. the dressing table brings you 3 temperature light modes, touch the button you can easy light up the mirror and changeet your different needs, long press to adjust the brightness TOUCH SWITCH 38-39...
Page 39
STEP31 We have included a set of tipping restraint hardware for NOTE this unit. You must install this hardware to prevent :The tipping restraint hardware included is for accidents or injuries that can result from the unit falling. wooden stud wall construction. It must be attached to a When properly installed, this restraint can provide wall stud.