Related Manuals for Dtronic DT3420
Summary of Contents for Dtronic DT3420
- Page 1 User Manual DT3420 Barcodescanner – DT3420 0645733500 info@diwolar.nl https://www.dtronic.nl/ Datum : 28-1-2024 Versie : 1.0...
-
Page 2: Introduction
User manual ‘DT3420’ Introduction Thank you for trusting a product from DTRONIC. Please read the contents of the user manual carefully in order to use the products safely and effectively. You are advised to keep this manual correctly for your installation and as a reference. Please do not disassemble the product or tear off the seal, otherwise we will not provide warranty or replacement service. -
Page 3: Table Of Contents
User manual ‘DT3420’ Inhoud INTRODUCTION .......................... 2 1. PRODUCT ..........................6 Function ..........................6 Unbox ..........................6 Start ..........................6 Window ..........................6 Reading ..........................7 Picture ..........................7 Led indicator ........................7 2. SYSTEM SETUP ........................8 System Setup ........................8 2.1.1 Setup code ...................... - Page 4 User manual ‘DT3420’ 2.6.5 Custom suffixes ....................21 2.6.6 Custom ID output method ......Fout! Bladwijzer niet gedefinieerd. 2.6.7 Customize Code ID .......... Fout! Bladwijzer niet gedefinieerd. 2.6.8 Terminator settings ....................21 2.6.9 CTRL + X ........................ 22 2.6.10 Case output settings ..................... 23 2.6.11 Data output settings .....................
- Page 5 User manual ‘DT3420’ 2.7.43 RSS-Limited ......................36 2.7.44 RSS-14 ........................37 2.7.45 Trioptic Code ......................37 2.7.46 Telepen ......................... 37 2.7.47 Straight 2 of 5 Industrial ..................37 2.7.48 Maxicode ......................38 2.7.49 Interleave 2 of 5 (ITF5) setting ................38 2.7.50 Extra code setting ..........
-
Page 6: Product
- Basically the scanner scans the 95% of bar codes, remaining 5% can be set as desired with this manual. - There are patented parts in the scanner, DTRONIC has the rights to sell these items on the Dutch, Belgian and German market 1.2 Unbox... -
Page 7: Reading
User manual ‘DT3420’ 1.5 Reading If the bar code is small, it should be closer to the scan window; if the bar code is large, it should be further away from the scan window for easier reading. If the bar code is highly reflective (for example, the coated surface), you may need to tilt the bar code at an angle to scan the bar code. -
Page 8: System Setup
User manual ‘DT3420’ 2. System Setup 2.1 System Setup Option and function setting mainly by reading a series of special bar codes. In this chapter, we give you a detailed introduction to the options and functions available for user setup and the corresponding setup code. -
Page 9: Pairing Bluetooth
User manual ‘DT3420’ 2.2 Pairing bluetooth Press the button on the scanner, the scanner turns on and a green light appears. Connect the USB connector to the computer or laptop, wait a few moments for the computer to find and actually see it. -
Page 10: Wireless
User manual ‘DT3420’ 2.3 Wireless Bluetooth HID Mode Quick Pair Bluetooth SPP Mode Bluetooth BLE Mode Bluetooth BLE Mode Android Input Method USB-Virtual COM Port Enable Long press to enter Bluetooth HID Mode Pairing Disable Long press to enter Bluetooth HID... -
Page 11: Bluetooth Name
User manual ‘DT3420’ 2.3.1 Bluetooth name First scan the "Bluetooth name setting" and then scan another barcode that becomes the Bluetooth name of this scanner. NOTE: The longest Bluetooth name can be 16 bytes. If the Bluetooth barcode is more than 16 bytes, the Bluetooth takes only the first 16 bytes as the Bluetooth name. -
Page 12: Led
User manual ‘DT3420’ 2.3.2 Led Enable Aimer Disable Aimer Enable Illumination Disable Illumination Always off Always on Blink test mode Disable blink test mode 2.3.3 Level lighting Datum : feb-2024 pagina 12 van 52 Versie : 1.0... -
Page 13: Beeper Duration
User manual ‘DT3420’ 2.3.4 Beeper Duration Short Normal 2.7Khz Mute 2.3.5 Beeper settings Volume set to High (50%) (default) Volume set to midrange (25%) Volume set to bass (12.5%) 2.3.6 Set the beep switch Open (default) Close Datum : feb-2024 pagina 13 van 52 Versie : 1.0... -
Page 14: Power On Beep Switch
User manual ‘DT3420’ 2.3.7 Power on beep switch Open (default) Close 2.3.8 Read success beep switch Open (default) Close 2.4 Reading mode settings 2.4.1 Level trigger mode Enter the reading state when the trigger key pin is at low level. Press and hold the trigger key to start reading code. -
Page 15: Pulse Trigger Mode
User manual ‘DT3420’ 2.4.3 Pulse trigger mode When the reading setting code is switched to this mode, it enters the pulse-triggered reading state. Pulse trigger mode High sensitivity Low sensitivity 2.4.4 Auto Scan mode Auto scan Delay 50ms Delay 100ms Delay 300ms 2.4.5 Code reading timeout... -
Page 16: One Read Timeout
User manual ‘DT3420’ 2.4.6 One read timeout One time reading timeout time, the unit is 0.1 seconds. The default value is 30 (3 seconds), when set to 0, it means that the device is always in the reading state, and the time range can be set: 0~999. -
Page 17: Communication Settings
User manual ‘DT3420’ 2.5 Communication settings 2.5.1 Communication settings USB HID (default) USB serial port USB CDC Enable virtual keyboard 2.5.2 USB keyboard Portuguese (Brazil) cannot output "?" and "/" . Nederlands Italian Spanish (Brazil) Portuguese Portuguese (Brazil) French German (Austria) -
Page 18: Usb Keyboard Sending Speed
User manual ‘DT3420’ Turkish F English (UK) Japanese German (Switzerland) French (Belgium) America 2.5.3 USB keyboard sending speed If there is missed data at the receiver side, the occurrence speed should be turned down, which is easy to occur at the receiver side with poor performance. -
Page 19: Control Characters
User manual ‘DT3420’ Setting the USB keyboard to send speed of 50ms can be set by reading the following barcodes in order. 1. Read "Startup Settings" 2. Read the "Set USB keyboard send speed" setting code 3. Read data code: "5" "0" (see data code table) 4. -
Page 20: Customized Prefixes
User manual ‘DT3420’ If set to "Off", the decoded information will only have the barcode data information, no prefix, and the default value is to turn off the custom prefix output. Enable Disable (default) 2.6.3 Customized prefixes The custom prefix adds a user-defined string before the decoded information, and the output format after customization is "Custom Content + Barcode Content". -
Page 21: Custom Suffixes
User manual ‘DT3420’ 2.6.5 Custom suffixes Custom suffix adds a user-defined string after the decoded information, and the output format after customization is "barcode content + custom content". Set the custom suffix to 'a' (the hex value of a is 0x61) 1. -
Page 22: Ctrl + X
User manual ‘DT3420’ 2.6.7 CTRL + X Non- printable Keyboard Control + ASCII ( CTRL+ X) Mode ASCII control characters Windows Mode Control + X Control + X Mode Off Mode On CTRL + X Char CTRL + X function... -
Page 23: Case Output Settings
User manual ‘DT3420’ CTRL+ T CTRL+ U CTRL+ V Paste CTRL+ W CTRL+ X CTRL+ Y CTRL+ Z CTRL+ [ CTRL+ \ CTRL+ ] CTRL+ ^ CTRL+ - NP Enter 2.6.8 Case output settings Case conversion for characters in a string, prefix and suffix have no effect. -
Page 24: Data Output Settings
User manual ‘DT3420’ 2.6.9 Data output settings OPMERKING: The prefix and suffix are not processed, and the prefix and suffix are output normally. Raw data output (default) Front-end data output Intermediate data output Back-end data output Start and end data output 2.6.10 Pre/Post data length setting... -
Page 25: All Symbologies
User manual ‘DT3420’ 2.7.1 1D all symbologies Enable Disable 2.7.2 2D all symbologies Enable Disable 2.7.3 QR mirror code Enable Disable 2.7.4 Inverse barcode Decode regular only Decode inverse only Datum : feb-2024 pagina 25 van 52 Versie : 1.0... -
Page 26: Data Matrix Mirror Code
User manual ‘DT3420’ 2.7.5 Data matrix mirror code Enable Disable 2.7.6 Mirror Code for all symbologies Enable Disable 2.7.7 All barcodes Close all barcodes Turn on all barcodes 2.7.8 EAN8 Settings EAN8 on (default) EAN8 off Enable EAN8 transmission Check Character... -
Page 27: Code 11 Settings
User manual ‘DT3420’ Convert EAN8 to EAN13 Do not Convert EAN8 to EAN13 (default) 2.7.9 Code 11 Settings Enable Disable 1 check bit 2 check bits Transmit check bit Not transmit check bit 2.7.10 Add-on code setting Adaptive UPC/EAN add-on codes... -
Page 28: Ean 13 Settings
User manual ‘DT3420’ 2.7.11 EAN 13 settings EAN13 on (default) EAN13 off Enable EAN13 transmission Check Character Disable EAN13 transmission checks (default) Transmit EAN13 System Character (default) Do not Transmit EAN13 System Character 2.7.12 HANXIN Enable Disable 2.7.13 UPC-A settings... -
Page 29: Upc-E Settings
User manual ‘DT3420’ Enable Disable 2.7.14 UPC-E settings UPC-E on (default) UPC-E Off Do no Transmit UPC-E transmission Check Transmit UPC-E Check Character (default) Character Extended to 12 bits Disable to 12 bits 2.7.15 UPCE Enable Disable 2.7.16 EAN/UPC Enable... -
Page 30: Code 39 Settings
User manual ‘DT3420’ Normal and inverse Normal baroce 2.7.17 Code 39 Settings Code 39 on (default) Code 39 off Enable Code 39 Check Character Disable Code 39 Check Character (default) Do not Transmit Code 39 Check Character Transmit Code 39 Check Character... -
Page 31: Code 32 Settings
User manual ‘DT3420’ 2.7.18 Code 32 settings Convert Code39 to Code32 Do not Convert Code39 to Code32 (default) 2.7.19 Code 128 settings Code 128 on (default) Code 128 Off Normal baroce Normal and inverse Transmit Code 128 Check Character Do not Transmit Code 128 Check Character (default) 2.7.20 Code 93 settings... -
Page 32: Codabar Settings
User manual ‘DT3420’ 2.7.21 Codabar Settings Codabar on (default) Codabar Off Transmit Codabar start and stop characters Do not Transmit Codabar start and stop characters (default) Not check Enable check transmit check bit Normal barcode Normal and inverse 2.7.22 Codablock A... -
Page 33: Gs1 Databar Limited
User manual ‘DT3420’ 2.7.24 GS1 Databar Limited Enable Disable 2.7.25 GS1 Databar omnidirectional Enable Disable 2.7.26 GS1 Databar Expanded Enable Disable 2.7.27 DOT_CODE Enable Disable 2.7.28 Composite Enable Disable Datum : feb-2024 pagina 33 van 52 Versie : 1.0... -
Page 34: Data Matrix Code
User manual ‘DT3420’ 2.7.29 Data matrix Code Enable Disable Enable Inverse DM Disable Inverse DM 2 of 5 enable 2 of 5 disable Matrix 2 of 5 check bit enable Matrix 2 of 5 check bit disable Output matrix 2 of 5 check bit Not output matrix 2 of 5 check bit 2.7.30 MSI... -
Page 35: Micro Qr Code
User manual ‘DT3420’ 2.7.31 QR Enable Disable Enable inverse QR Disable inverse QR Enable QR code URL link Disable QR code URL link 2.7.32 Micro QR code Enable Disable Inverse micro QR Disable inverse micro QR 2.7.33 PDF417 Enable Disable... -
Page 36: Micro Pdf417
User manual ‘DT3420’ Normal baroce Normal and inverse 2.7.34 Micro PDF417 Enable Disable 2.7.35 Pharmacode Enable Disable 2.7.36 RSS-Expanded Enable Disable 2.7.37 RSS-Limited Enable Disable Datum : feb-2024 pagina 36 van 52 Versie : 1.0... -
Page 37: Rss-14
User manual ‘DT3420’ 2.7.38 RSS-14 Enable Disable 2.7.39 Trioptic Code Enable Disable 2.7.40 Telepen Enable Disable 2.7.41 Straight 2 of 5 Industrial Enable Disable Datum : feb-2024 pagina 37 van 52 Versie : 1.0... -
Page 38: Maxicode
User manual ‘DT3420’ 2.7.42 Maxicode Enable Disable 2.7.43 Interleave 2 of 5 (ITF5) setting ITF5 on (default) ITF5 off Enable ITF25 check character (default) Disable ITF25 Check Character Transmit ITF25 Check Character Do not Transmit ITF25 Check Charcter (default) Normal baroc Normal and inverse 2.7.44 Airline 2 of 5... -
Page 39: Aztec Code
User manual ‘DT3420’ 2.7.45 Aztec code Enable Disable Enable inverse Aztec Disable inverse Aztec Datum : feb-2024 pagina 39 van 52 Versie : 1.0... -
Page 40: Appendix
User manual ‘DT3420’ 3. Appendix 3.1.1 Control Character Table ASCII Programming Barcode NULL Home Ctrl+A Alt+001 Ctrl+B Ctrl+B Alt+002 Lock Right Ctrl+C Up Arrow Ctrl+C Alt+003 Arrow Down Ctrl+D Alt+004 Arrow Arrow Left Ctrl+E Alt+005 NULL Arrow Right Ctrl+F Alt+006... - Page 41 User manual ‘DT3420’ Down Enter Enter Ctrl+P Alt+010 Arrow NULL NULL Ctrl+Q Alt+011 NULL NULL Ctrl+R Alt+012 delete Enter Enter Enter Alt+013 Enter Page Up Ctrl+N Alt+014 Insert Page Ctrl+O Alt+015 Down Ctrl+P Alt+016 NULL Ctrl+Q Alt+017 Home Print NULL...
- Page 42 User manual ‘DT3420’ Ctrl+U Alt+021 Ctrl+V Alt+022 Ctrl+W Alt+023 Ctrl+X Alt+024 Ctrl+Y Alt+025 NULL Ctrl+Z Alt+026 Ctrl+[ Alt+027 ALT+028 Ctrl+\ Alt+028 ALT+029 Ctrl+] Alt+029 NULL Ctrl+^ Alt+030 NULL Ctrl+_ Alt+031 Datum : feb-2024 pagina 42 van 52 Versie : 1.0...
- Page 43 User manual ‘DT3420’ 3.1.2 Visible Characters Deci ASCII Programming Barcode Data Space " & Datum : feb-2024 pagina 43 van 52 Versie : 1.0...
- Page 44 User manual ‘DT3420’ Datum : feb-2024 pagina 44 van 52 Versie : 1.0...
- Page 45 User manual ‘DT3420’ < > Datum : feb-2024 pagina 45 van 52 Versie : 1.0...
- Page 46 User manual ‘DT3420’ Datum : feb-2024 pagina 46 van 52 Versie : 1.0...
- Page 47 User manual ‘DT3420’ Datum : feb-2024 pagina 47 van 52 Versie : 1.0...
- Page 48 User manual ‘DT3420’ Datum : feb-2024 pagina 48 van 52 Versie : 1.0...
- Page 49 User manual ‘DT3420’ Datum : feb-2024 pagina 49 van 52 Versie : 1.0...
- Page 50 User manual ‘DT3420’ Datum : feb-2024 pagina 50 van 52 Versie : 1.0...
- Page 51 User manual ‘DT3420’ Ç Datum : feb-2024 pagina 51 van 52 Versie : 1.0...
-
Page 52: Datum : Feb-2024 Pagina 3 Van
User manual ‘DT3420’ ç Datum : feb-2024 pagina 52 van 52 Versie : 1.0...
Need help?
Do you have a question about the DT3420 and is the answer not in the manual?
Questions and answers