Table of Contents
Advertisement
Quick Links
OPERATOR'S MANUAL
MODEL #100304
22-kW HOME STANDBY GENERATOR
WITH aXis CONTROLLER
®
ACTIVATE YOUR WARRANTY
SERIAL NO.
by registering your product:
championpowerequipment.com
or visit championpowerequipment.com
SAVE THESE INSTRUCTIONS. This manual contains important safety precautions which should be read and understood before operating the product. Failure to do
so could result in serious injury. This manual should remain with the product.
Specifications, descriptions and illustrations in this manual are as accurate as known at the time of publication, but are subject to change without notice.
No part of this publication may be reproduced or used in any form by any means – graphic, electronic or mechanical, including photocopying, recording, taping or
information storage and retrieval systems – without the written permission of Champion Power Equipment (CPE).
EN
4328-M-OP REV 20231212
Champion Power Equipment, Inc.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Champion 100304
Summary of Contents for Champion 100304
- Page 1 No part of this publication may be reproduced or used in any form by any means – graphic, electronic or mechanical, including photocopying, recording, taping or information storage and retrieval systems – without the written permission of Champion Power Equipment (CPE).
- Page 2 FREE 10 YEAR WARRANTY www.championpowerequipment.com/HSB-offer PLUS, GET A FREE T-SHIRT! In exchange for an honest rating and review of your Champion product, we'll give you a FREE T-SHIRT! REGISTRATION REQUIREMENTS - Full name - Address where installed - Phone number...
- Page 3 – or – Call our Customer Care Team Toll-Free at: 1-877-338-0999 This manual must be used with Champion Power Equipment (CPE) manuals: Installation Manual Transfer Switch Manual * We are always working to improve our products. Therefore, the enclosed product may differ slightly from the image on the cover.
-
Page 4: Table Of Contents
TABLE Of CONTENTS 100304 - 22-kW HOME STANDBY GENERATOR WITH AXIS CONTROLLER ® TABLE Of CONTENTS Operation ........... .. -
Page 5: Introduction
INTRODUCTION 100304 - 22-kW HOME STANDBY GENERATOR WITH AXIS CONTROLLER ® HOME STANDBY GENERATOR INTRODUCTION Congratulations on your purchase of a Champion Power Equipment This home standby generator is intended exclusively for outdoor (CPE) product. CPE designs, builds, and supports all of our installation. -
Page 6: Important Safety Instructions
IMPORTANT SAfETY INSTRUCTIONS 100304 - 22-kW HOME STANDBY GENERATOR WITH AXIS CONTROLLER ® IMPORTANT SAfETY INSTRUCTIONS DANGER Carbon Monoxide (CO) is a colorless, odorless, poisonous WARNING gas. Breathing carbon monoxide will cause nausea, dizziness, Cancer and Reproductive Harm – www.P65Warnings.ca.gov fainting or death. -
Page 7: Installation Hazards
IMPORTANT SAfETY INSTRUCTIONS 100304 - 22-kW HOME STANDBY GENERATOR WITH AXIS CONTROLLER ® Before Starting WARNING WARNING Smoke alarms cannot detect Carbon Monoxide (CO) gas. To better educate yourself about all carbon monoxide risks, go Before operation, read and understand the features and to www.takeyourgeneratoroutside.com... -
Page 8: Accidental Starting
IMPORTANT SAfETY INSTRUCTIONS 100304 - 22-kW HOME STANDBY GENERATOR WITH AXIS CONTROLLER ® Accidental Starting fuel Safety WARNING DANGER ALWAYS prevent the generator from starting while the covers PROPANE AND NATURAL GAS ARE HIGHLY FLAMMABLE are open. The generator may crank and start at any time AND EXPLOSIVE. -
Page 9: Burn Hazards
IMPORTANT SAfETY INSTRUCTIONS 100304 - 22-kW HOME STANDBY GENERATOR WITH AXIS CONTROLLER ® Entanglement Hazards DANGER WARNING NEVER allow any flames or smoke near the fuel system. Wipe up any oil spills immediately. Use extreme caution when near rotating parts. Rotating parts can entangle hands, feet, hair, clothing and/or accessories. -
Page 10: Safety Symbols
SAfETY 100304 - 22-kW HOME STANDBY GENERATOR WITH AXIS CONTROLLER ® Safety Symbols Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to more safely operate the product. - Page 11 SAfETY 100304 - 22-kW HOME STANDBY GENERATOR WITH AXIS CONTROLLER ® SYMBOL MEANING Sever hazard (rotating blade) Crush hazard (top) Explosion Hazard. Battery gases are explosive. Keep sparks and flames away from the battery compartment.
-
Page 12: Safety Labels And Hang Tags
D- update to have Eng,Spa,Fr in order. This artwork belongs to Champion Power Equipment. The contents are confidential and privileged and shall not be disclosed to or used by or for outside parties without the explicit consent of Champion Power Equipment. - Page 13 (PE/PP mix) This artwork belongs to Champion Power Equipment. The contents are confidential and privileged and shall not be disclosed to or used by or for outside parties without the explicit consent of Champion Power Equipment.
-
Page 14: Safety Label And Hang Tag Locations
SAfETY LABELS AND HANG TAGS 100304 - 22-kW HOME STANDBY GENERATOR WITH AXIS CONTROLLER ® Safety label and Hang Tag locations The safety labels have specific placement and must be replaced if they are unreadable, damaged or missing. If a label comes off or becomes hard to read, contact Technical Support Team for possible replacement. -
Page 15: General Information
GENERAL INfORMATION 100304 - 22-kW HOME STANDBY GENERATOR WITH AXIS CONTROLLER ® GENERAL INfORMATION Component Identification - Home Standby (HSB) Generator 1. Exhaust System 8. Electric Conduit Cap 2. Engine 9. Exterior Warning LED 3. Air Inlet 10. Fuel Inlet 4. -
Page 16: Component Identification - Engine
GENERAL INfORMATION 100304 - 22-kW HOME STANDBY GENERATOR WITH AXIS CONTROLLER ® Component Identification - Engine 1. Engine Oil Dipstick 2. Air Cleaner 3. Oil Cap 4. Spark Plug (second on opposite side) 5. Oil Filter... -
Page 17: Control Panel
GENERAL INfORMATION 100304 - 22-kW HOME STANDBY GENERATOR WITH AXIS CONTROLLER ® Control Panel Inside Back MAIN CIRCUIT BREAkER The 100-amp main circuit breaker protects the generator from circuit overload. The main circuit breaker controls total output of the generator. The main circuit breaker must be in the ON position for the aXis ATS to communicate with this standby generator. -
Page 18: Fcc Statement
GENERAL INfORMATION 100304 - 22-kW HOME STANDBY GENERATOR WITH AXIS CONTROLLER ® fCC Statement aXis Controller ® * Applicable in USA only. The aXis Controller is equipped to provide monitoring and ® protection for the HSB. 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1a. - Page 19 GENERAL INfORMATION 100304 - 22-kW HOME STANDBY GENERATOR WITH AXIS CONTROLLER ® aXis CONTROLLER STATUS ICONS aXis CONTROLLER INfORMATION ICONS ® ® The status icons are located at the top of the aXis Controller The information icons are located at the bottom right side of aXis ®...
- Page 20 DO NOT overfill. Inspect the unit for a possible Insufficient battery output could result in poor cranking cycles, oil leak, if a leak is discovered, contact Champion or your nearest not permitting the engine starter to reach optimum starting RPM Authorized Champion Dealer.
- Page 21 ® If this failure occurs, contact Champion or your Authorized Requires Maintenance Champion Dealer. The RED icon will remain lit until the failure has been corrected, the HSB will not attempt to transfer or run. Line Over Voltage The RED icon will be lit if the HSB generator is ready for maintenance.
-
Page 22: Wi-Fi Setup Method
GENERAL INfORMATION 100304 - 22-kW HOME STANDBY GENERATOR WITH AXIS CONTROLLER ® Wi-fi Setup Method 3. After connecting Wi-Fi, open your device’s web browser. In the browser address change the address to 192.168.0.90 and 1. Use a Wi-Fi enabled device (laptop, smart phone, tablet, etc.) begin search. - Page 23 Home Standby GENERAL INfORMATION 100304 - 22-kW HOME STANDBY GENERATOR WITH AXIS CONTROLLER ® Generator Settings 5. Confirm and apply the settings before continuing. If you do 7. Set the HSB exercise frequency and schedule. not apply immediately, the clock will be later than actual.
-
Page 24: Ats And Hsb Status Using Wifi
2. After the HSB is set to OFF, press and hold until the screen 1. Using a WIFI enabled device, connect to the “Champion HSB” changes (decimal point will flash) to enter programming WIFI network following steps 1, 2, and 3 from WIFI Setup mode. - Page 25 GENERAL INfORMATION 100304 - 22-kW HOME STANDBY GENERATOR WITH AXIS CONTROLLER ® 6. Week Day - choose week day from 1 to 7. Hour (exercise) - choose hours in military time 0 - 23. Set week using Set hour using...
-
Page 26: Battery Charger
DC This artwork belongs to Champion Power Equipment. The contents are confidential and privileged and shall not be disclosed to or used by or for outside parties without the explicit consent of Champion Power Equipment. -
Page 27: Specifications
GENERAL INfORMATION 100304 - 22-kW HOME STANDBY GENERATOR WITH AXIS CONTROLLER ® Specifications Home Standby Generator Maximum continuous power, LPG 22 kW Maximum continuous power, NG 19.8 kW Rated voltage 120/240 Amps 183.4/91.7 LPG (propane), 165/82.5 NG (natural gas) Harmonic distortion... -
Page 28: Fuel System
GENERAL INfORMATION 100304 - 22-kW HOME STANDBY GENERATOR WITH AXIS CONTROLLER ® fuel System The engine is fitted with a dual master mixer assembly carburation Automotive system, which allows it to run on either NG or LPG. It has been Post Style configured at the factory to run on NG. -
Page 29: Model And Serial Number
OPERATION 100304 - 22-kW HOME STANDBY GENERATOR WITH AXIS CONTROLLER ® OPERATION Model and Serial Number The model and serial number plate is affixed to the generator Before operating the generator, review SAFETY section above the control panel. Have this information if calling for service starting on page 6. -
Page 30: Turning Off The Generator
MAINTENANCE 100304 - 22-kW HOME STANDBY GENERATOR WITH AXIS CONTROLLER ® Turning Off the Generator Spark Plug Specifications If you need to shut off the generator when it is running, put the OEM Type ............K7RTC aXis Controller in the OFF position. This will shut off the engine. -
Page 31: Changing The Engine Oil
MAINTENANCE 100304 - 22-kW HOME STANDBY GENERATOR WITH AXIS CONTROLLER ® 3. Remove the dipstick. Wipe it dry with a clean cloth and 3. Press the OFF button on the aXis Controller ® completely reinsert it into the dipstick tube. -
Page 32: Inspect And Clean Engine Air Cleaner
MAINTENANCE 100304 - 22-kW HOME STANDBY GENERATOR WITH AXIS CONTROLLER ® 9. After the oil is drained, reinstall the oil drain hose cap by 5. Remove the paper element/ foam filter. screwing it back on snugly, making sure o-ring is in place. -
Page 33: Battery Maintenance
MAINTENANCE 100304 - 22-kW HOME STANDBY GENERATOR WITH AXIS CONTROLLER ® Resetting the Maintenance Hour Meter 5. Clean the area around the spark plug to keep dirt out of the engine and remove the spark plug. The maintenance hour meter counts down 100 hours. Once 6. -
Page 34: Corrosion Protection
MAINTENANCE 100304 - 22-kW HOME STANDBY GENERATOR WITH AXIS CONTROLLER ® Corrosion Protection NOTICE Never use a pressure washer to wash the interior of the generator with water. Wash the outside of the enclosure using a mild soap and water. -
Page 35: Troubleshooting Hsb
MAINTENANCE 100304 - 22-kW HOME STANDBY GENERATOR WITH AXIS CONTROLLER ® TROUBLESHOOTING HSB Engine will not crank/turn over HSB set in “OFF” mode. Place the HSB controllers in the AUTO position. Connect the batteries according to owner’s manual, clean and tighten... - Page 36 BATTERY(S) NO OR LOW LEVEL CHARGED, BATTERY(S) DEAD, NEEDS REPLACEMENT, THE EXERCISE TIME MUST BE RESET ONCE THE BATTERY(S) HAVE BEEN DISCONNECTED. * *Contact Champion Power Equipment, Technical Service toll free 1-877-338-0999, tech@championpowerequipment.com or your nearest Champion dealer. www.championpowerequipment.com...
-
Page 37: Additional Information
ADDITIONAL INfORMATION 100304 - 22-kW HOME STANDBY GENERATOR WITH AXIS CONTROLLER ® ADDITIONAL INfORMATION Surge Protection CAUTION Voltage fluctuation may impair the proper functioning of sensitive electronic equipment. Electronic devices, including computers and many programmable appliances use components that are designed to operate within a narrow voltage range and may be affected by momentary voltage fluctuations. -
Page 38: Hsb, Ats Model & Serial Reference Ats Back-Up Circuits
ADDITIONAL INfORMATION 100304 - 22-kW HOME STANDBY GENERATOR WITH AXIS CONTROLLER ® HSB, ATS Model & Serial Reference ATS Back-up Circuits HSB Model Number HSB Serial Number Fuel Type ATS Model Number ATS Serial Number ATS circuits powered Date Installed... -
Page 39: Maintenance And Service Record
Genuine Champion parts must be used to ensure warranty coverage. Date Hour Meter Service Preformed Record the name, address and phone number of your authorized Champion dealer... - Page 40 THIS WARRANTY SHALL NOT APPLY TO THE and testing by Champion Power Equipment or an Authorized FOLLOWING: Champion Home Standby Dealer is found to be defective under – Original installation or start-up costs normal use and service, in accordance with the Warranty Schedule set forth below.
- Page 41 THE REPAIR OR REPLACEMENT OF PART(S) AS STATED ABOVE. IN NO EVENT SHALL CHAMPION POWER EQUIPMENT BE LIABLE FOR ANY INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF SUCH DAMAGES ARE A DIRECT RESULT OF CHAMPION POWER EQUIPMENT’S NEGLIGENCE. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations may not apply to purchaser/owner.
- Page 42 AND THE UNITED STATES ENVIRONMENT PROTECTION AGENCY (U.S. EPA) EMISSION CONTROL SYSTEM WARRANTY Your Champion Power Equipment (CPE) engine complies with U.S. EPA emission regulations. YOUR WARRANTY RIGHTS AND OBLIGATIONS: The US EPA AND CPE are pleased to explain the Federal Emission Control Systems Warranty on your 2023 small off-road engine (SORE) and engine powered equipment.
- Page 43 EMISSION CONTROL SYSTEM WARRANTY The following are specific provisions relative to your Emission Control System (ECS) Warranty Coverage. 1. APPLICABILITY: This warranty shall apply to 1997 and later model year small off-road engines (SORE). The ECS Warranty Period shall begin on the date the new engine or equipment is delivered to its original, end-use purchaser, and shall continue for 24 consecutive months thereafter.
- Page 44 You must take your CPE engine or the product on which it is installed, along with your warranty registration card or other proof of original purchase date, at your expense, to any Champion Power Equipment dealer who is authorized by Champion Power Equipment, Inc. to sell and service that CPE product during his normal business hours.
Need help?
Do you have a question about the 100304 and is the answer not in the manual?
Questions and answers
22kw champion generator exercise time how many minters each week?
A 22kW Champion generator should be exercised for 15 minutes per week.
This answer is automatically generated