Table of Contents
Advertisement
Available languages
Available languages
MAINTENANCE INSTRUCTIONS
MAINTENANCE INSTRUCTIONS
Clean lint screen before and after each cycle.
■
Removing accumulated lint:
■
From inside the dryer cabinet:
Lint should be removed every 2 years or more often,
depending on dryer usage. Cleaning should be done by
a Whirlpool authorized person.
From the exhaust vent:
Lint should be removed every 2 years, or more often,
depending on dryer usage.
Keep area around dryer clear and free from combustible
■
materials, gas, and other flammable vapors and liquids.
Keep dryer area clear and free from items that would
■
obstruct the flow of combustion and ventilation air.
If dryer does not operate, check the following:
Electrical supply is connected.
■
Circuit breaker is not tripped or house fuse is not blown.
■
Door is closed. Listen closely to hear the door switch
■
activate.
Controls are set in a running or "on" position.
■
For gas dryers, check that gas supply shut-off valves are set
■
in open position.
WARNING:
Improper connection of the equipment-
earthing conductor can result in a risk of electric shock. It
is your responsibility to check with a qualified electrician
or service representative if you are in doubt as to whether
the dryer is properly earthed and meets all local codes and
ordinances. Do not modify the plug provided with the dryer:
If it will not fit the outlet, have a proper outlet installed by a
qualified electrician.
IF YOU NEED ASSISTANCE
IF YOU NEED ASSISTANCE
If you need help, contact the dealer from whom you purchased
the appliance, or a Maytag designated service company. When
calling, please know the purchase date and the complete
model and serial number of your appliance. This information
will help us to better respond to your request.
IF YOU NEED SERVICE:
Contact your authorized Maytag Commercial Laundry
distributor. To locate your authorized Maytag Commercial
Laundry distributor, visit www.maytagcommerciallaundry.
com.
For written correspondence:
Maytag Commercial Laundry Service Department
2000 N M 63
Benton Harbor, Michigan 49022-2632 USA
TOOLS & PARTS
TOOLS & PARTS
Tools Needed:
A
D
G
J
M
Q
A. 8" (200 mm) or 10" (250 mm) Pipe wrench
B. 8" (200 mm) or 10" (250 mm) adjustable wrench that opens to
1" (25 mm) wrench
C. 27" (686 mm) Wood block
D. Flat-blade screwdriver
E Phillips screwdriver
F. TORX
®
T20
®†
security screwdriver or bit
G. 1" (25 mm) Hex-head socket wrench
H. 5/16" (8 mm) Socket wrench
I. Pliers (that open to 1
/
" [39.7 mm])
9
16
J. Level
K. Utility knife
L. Ruler or measuring tape
M. Caulk gun and caulk (for installing new exhaust vent)
N. Vent clamps
O. Putty knife
P. Pipe-joint compound suitable for gas type
Q. 1/4" (6 mm) Nut driver
Parts Supplied:
R
U
R. Foot Boots (4)
S. Leveling Legs (4)
T. Bezel kit (PR models only)
U. Security cone (PD models only)
V. Lock cam (on some models)
W. 5/16" hex-head 18 x 2½" security bolt (PD models only)
NOTE: The circuit diagram for this dryer is located inside
the lower front panel, within the Tech Sheets.
Technical Specifications:
220–240 V, 50 Hz AC
4575 W
Total mass: 68 kg maximum
†
TORX and T20 are trademarks of Acument Intellectual Properties, LLC.
®
B
C
F
E
I
H
K
L
N
O
S
V
W
P
T
7
Advertisement
Table of Contents
