1. Manuals
  2. Brands
  3. Graco Manuals
  4. Lubrication systems
  5. 24Z764
  6. Instructions manual

Graco Jockey 24Z764 Instructions Manual

Automatic lubrication system
Hide thumbs Also See for Jockey 24Z764:
Table of Contents

Advertisement

Quick Links

Download this manual
Instructions
Electric Grease Jockey
Automatic Lubrication
System
For dispensing NLGI Grades #000 to #2 greases. For Professional Use Only.
Not approved for use in explosive atmospheres or hazardous locations.
Models: 24Z764, 24Z959, 24Z660, 23Z958, 26C494, 25V619
2000 psi (13.79 MPa, 137.9 bar)
Models: 26C495, 26A848
1000psi (6.89 MPa, 68.9 bar) 26C495, 26A848
Important Safety Instructions
Read all warnings and instructions in
this manual before using the equipment.
Be familiar with the proper control and
usage of the equipment. Save these
instructions.
®
3A5082N
EN

Advertisement

Table of Contents
loading

Related Manuals for Graco Jockey 24Z764

Summary of Contents for Graco Jockey 24Z764

  • Page 1 Instructions ® Electric Grease Jockey Automatic Lubrication System 3A5082N For dispensing NLGI Grades #000 to #2 greases. For Professional Use Only. Not approved for use in explosive atmospheres or hazardous locations. Models: 24Z764, 24Z959, 24Z660, 23Z958, 26C494, 25V619 2000 psi (13.79 MPa, 137.9 bar) Models: 26C495, 26A848 1000psi (6.89 MPa, 68.9 bar) 26C495, 26A848 Important Safety Instructions...

  • Page 2: Table Of Contents

    Time Control ......44 Graco Information......84 Alarms .

  • Page 3: Safety Symbols

    Safety Symbols Safety Symbols The following safety symbols appear throughout this manual and on warning labels. Read the table below to understand what each symbol means. Symbol Meaning Symbol Meaning Splash Hazard Cleaning Solvent Hazard Consult Doctor Electric Shock Hazard Ground Equipment Equipment Misuse Hazard Read Manual...

  • Page 4: General Warnings

    General Warnings General Warnings The following warnings apply throughout this manual. Read, understand, and follow the warnings before using this equipment. Failure to follow these warnings can result in serious injury. WARNING EQUIPMENT MISUSE HAZARD Misuse can cause death or serious injury. •...
  • Page 5 General Warnings WARNING PLASTIC PARTS CLEANING SOLVENT HAZARD Many cleaning solvents can degrade plastic parts and cause them to fail, which could cause serious injury or property damage. • Use only compatible solvents to clean plastic structural or pressure-containing parts. •...

  • Page 6: Set Up

    Set Up Set Up Grease Fittings Pressure Relief Procedure a. Lubricate all of the grease fittings with a grease Follow the Pressure Relief Procedure whenever gun and verify every grease point accepts you see this symbol. grease. b. Use a clean cloth or rag to remove any extra grease, contaminants or dirt from the area around the passage way to the grease points.

  • Page 7: Typical System Installation

    The installations shown in F . 2 and F . 3 are only guides for selecting and installing system components and accessories. Contact your Graco distributor for assistance in designing a system. Key: Banjo Bolt / Pump Outlet Feed Line Tubes...
  • Page 8 Typical System Installation 3A5082N...

  • Page 9: Pump

    Pump Pump Component Identification Part No: 24Z764: 12 V Standard 24Z959: 24 V Standard 26C494: 12 V, DMS with follower 26C495: 12 V Standard 1000 psi 24Z660: 12 V, DMS and Illuminated Remote Run Button Capable 24X958: 24 V, DMS and Illuminated Remote Run Button Capable 26A848: 24 V, DMS and Illuminated Remote Run Button Capable 1000 psi 25V619: 12 V, Telematic Outputs, Pressure Feedback, and Illuminated Remote Run Button Capable...

  • Page 10: Parts

    Pump Parts Models: 24Z660, 24Z958, 24Z764, 24Z959, 26C494, 26C495, 26A848, 25V619 3A5082N...

  • Page 11: Parts

    Pump Parts Models: 24Z660, 24Z958, 24Z764, 24Z959, 26C494, 26C495, 26A848, 25V619 Part Description Part Description 129801 CABLE, M12 X DEUTSCH BASE, with control 38▲ 16A579 LABEL, safety, warning, pressure 278142 COVER, bottom, w/seal 115477 SCREW, mach, orx pan hd ▲ Replacement safety labels, tags, and cards are available at no cost 13❖...

  • Page 12: Pump Dimensions

    Pump Pump Dimensions 3A5082N...

  • Page 13: Select An Installation Location

    NOTE: Mounting brackets (Part Nos. 25T767 and 25T567) are suitable for mounting on most truck frames, and are available from Graco. Contact your local Graco distributor for assistance with ordering this part. See F .
  • Page 14 Pump . 10: Outside Truck Frame Mount Installation (Kit 25T767) . 11: Outside Truck Frame Mount Installation (Kit 25T767) 3A5082N...
  • Page 15 Pump Mounting Bracket and Pump Dimensions . 12 3A5082N...
  • Page 16 Pump Pump Wiring Diagram (Standard Models: 24Z764, 24Z959, 26C494, AND 26C495) The pump requires a 2-wire, CPC Connector Cable (Part No. 129644) to power the pump. See the Wiring Schematic provided in F . 13. . 13 Pump Wiring Diagram (Models with DMS and Illuminated Remote Run Button: 24Z660, 24Z958, 26C494 AND 26A848) The pump requires a 5-wire, CPC Connector Cable (Part No.
  • Page 17 Pump Pump Wiring Diagram (Model with Telematic Outputs and Illuminated Remote Run Button: 25V619) The pump requires a 5-wire, CPC Connector Cable (Part No. 127782) to power the pump and illuminated remote run button. See the Wiring Schematic provided in F .

  • Page 18: Low Level Fault/Warning

    • Never operate pump without a fuse installed. • A fuse of the correct voltage must be installed in line with the power entry to the system. Graco Fuses . 16 Part No. Description Amps If the pump reservoir is not refilled with grease, the...

  • Page 19: Pump Over-Current Protection

    Pump Pump Over-Current Protection The pump has built-in over-current protection to protect the motor. In cold weather installations, if the grease freezes, the motor draws more current. The motor attempts to start the pump 90 times before it shuts down. How Over-Current Protection Works When the pump is unable to start the ON Time cycle, an over-current condition is created:...

  • Page 20: Tri-Color Remote Illumination

    Pump 4. Clean the surface around the outer edge of the push button (51). Position label (53) around the button and adhere label (F . 20). . 20 5. Clean the area close to the push button for mounting the label (55) inside of the cab. Adhere label to the mounting surface.
  • Page 21 Pump Pin and Related Wire Color (F . 22) Inputs (M12) (25V619) See Technical Specifications, page 82 for ratings. Pin Name Color Not Used Not Used -VDC Black +VDC/LED+ LED-/Alarm Out White Manual Run Switch Orange Not Used Not Used Low Level Out Green .

  • Page 22: Direct Mount Vent Valve

    25C966 (2000 psi) and 26A856 (1000 psi) for 24 Volt pressure relief valve to decrease pressure may pumps are available from Graco. Contact your local negatively impact on the performance of the pump or Graco Distributor or Graco Customer Service for the lubrication system.

  • Page 23: Pump Setup

    Pump Pump Setup Fill the Reservoir To ensure optimal performance from the pump: • Only use NLGI #000 - #2 greases appropriate for the application, automatic dispensing, and the operating temperature of the equipment. Consult with machine and lube manufacturer for details. •...

  • Page 24: Prime The Pump

    Pump Prime the Pump NOTE: It is not necessary to prime the pump every time the pump is filled with lubricant. The pump only requires priming the first time used or if it is allowed to run dry. 1. Loosen the pump outlet fitting (F .

  • Page 25: Program The Pump

    Pump Program the Pump Control Panel Overview (F . 32) NOTE: Program instructions begin on page 26. . 32 3A5082N...

  • Page 26: Quick Setup Guide - Dms And Illuminated Remote Run Models

    If it does not display, contact Graco Customer Service. By default, units with controllers are set to operate in a timed mode with 7 minutes of ON time and 2 hours and 53 minutes of OFF time.
  • Page 27 Pump Enter a PIN Code to Access Setup Mode Set the Real Time Clock DMS and Illuminated Remote Run Button The controller does not require a PIN code to access the programming features of the unit. However, some Models users may want to protect the programming settings so an option for adding PIN Code authorization is NOTE: Set the real time clock before plugging the USB available.
  • Page 28 Pump Enter the Month The time displays indicating the unit is ready to program the time. Enter the Time • The time is set in Hours and Minutes (HH:MM). • The LED under the HH lights when setting hours, and 1.
  • Page 29 Pump Pressure Control (P1, P2, P3) Setup Input Not Used (Model 25V619 Only) Select OFF if the system does not use the applicable input. • For injector systems, monitoring pressure can be used to ensure sufficient pressure has been 1. Use UP and DOWN ARROW reached to activate the injectors.
  • Page 30 Pump ON Time or Backup Time Program ON Time NOTE: When a time of less than 10 minutes is being • The LED next to the clock in the programmed, enter a leading zero (0) in the first number ON field lights to indicate the ON field and press the ENTER button to save the zero Time parameters are being set.

  • Page 31: Pump Off / Rest Setup

    1 1/2 or 2 hr wet climate, heavy loads, dusty and the value must be updated. roads. If this time does not meet the application needs, contact Graco Customer Support. Normal city or highway driving, 3 hr normal climate, moderate loads. Program OFF Time NOTE: When a time of less than 10 hours is being ™...
  • Page 32 1. Plug the USB flash drive into the USB port (D). The pump program settings file is named: NOTE: GRACO/Config/config.bin. This file cannot be modified. Modification of the file or file name may cause it to be The USB flash drive must contain file unusable.
  • Page 33 8. When the upload is • Log Name finished, the display • DMS ID Number reads done. • Current Software Graco Part No. • Current Software Version 9. The pump resumes operation. • Date and Time of Upload 10. Remove the USB flash drive.
  • Page 34 Pump Sample System Event Log Example Event Log: The pump cycle of a typical lubrication system is shown below. System Event Log DMS ID Number: 00613 Software Part No.: 17J936 Software Version: 0703 09/29/2016 14:1400 Date Time Description 9/29/2016 14:13:02 Pump Run Off 9/29/2016 14:13:02 Program Variable Change...

  • Page 35: Error Log

    Check the unit and system to The log file is stored as: determine that it is functioning correctly. Operating outside of GRACO/{DMS_id}/{download date - the specified temperature YYYYmmDD}/ERRORLOG.CSV range may cause reduced performance and possible unit Example: GRACO/00613/20160911/ERRORLOG.CSV.
  • Page 36 Pump USB File Not Found The pump program setting file was not found or created correctly. Restore the setting file to the flash drive. USB Folder The pump program setting file Navigation was not found or created correctly. Restore the setting file to the flash drive.

  • Page 37: Functional Summary

    This is very similar to a car odometer. Functional and Technical User Summary, page 42). The log file is stored as: This is very similar to the resettable car trip odometer. GRACO/pump_{DMS_id}/{download date - YYYYmmDD}/FUNCSUM.CSV Example: GRACO/pump_00025/20100911/FUNCSUM.CSV Sample Functional Summary...

  • Page 38: Technical Summary

    The average percentage of time The log file is stored as: the unit has been pumping while it has been powered on. GRACO/{DMS_id}/{download date - Max Duty Cycle The highest percentage of time YYYYmmDD}/TECHSUM.CSV for one lubrication cycle that the unit has been pumping while it Example: GRACO/00025/20100911/TECHSUM.CSV...
  • Page 39 Pump Sample Technical Summary Functional Summary DMS ID Number:00613 (Hold Down Arrow On Pump to View) Software Part No.: 17J936 Software Version:0703 9/13/2016 11:15:35 Latest Values Temp Voltage 11.846 Type Start Date Average Peak Average Peak Average Peak Board Board Motor Motor Internal...
  • Page 40 Pump Advanced Programming Identifies each option and when used. Advanced Model Setting Format/ Description Why Use This? Option All Models Lockout Secures setup modes with PIN Prevents unauthorized users to adjusting Code (Optional) settings. Telematic Alarm Retry Sets the number of automatic Establishes the number of time that the unit retires after a Cycle or Pressure automatically retires lubrication after a...
  • Page 41 Pump Enter a PIN Code for the First Time Enter Advanced Setup Press the UP ARROW button for 10 A1 - Set Up PIN Code seconds. A PIN Code can be programmed into the pump to protect the settings from inadvertently being changed If the pump was previously set to require a by unauthorized users.
  • Page 42 0. For assistance in determining a reasonable number of Alarm Retries to program for the application, The Pump Summary shows run details since the last contact Graco Customer Service or your local Graco time the summary was cleared. distributor.
  • Page 43 Pump A7- Constant Alarm Output ON Fault A10 - Low Level Reset Upon Power On. (Models with Firmware 5.04 and later. DMS This changes the behavior of the alarm output in a fault Models with Firmware 7.07 and later.) from either toggling once per second (default) or steady This changes the behavior of the low level upon pump power on.

  • Page 44: Time Control

    Pump Time Control A11- Warning Off Through Alarm Relay This changes the behavior of the alarm output in a After setup is complete, the pump automatically begins warning condition to always off. to run the OFF Time sequence (F . 36). •...
  • Page 45 Pump • The example shown in F . 37 shows an ON Time In the OFF state, it resumes the cycle with the same of 6 minutes before the lubrication cycle ends. amount of time remaining in the cycle when power was lost.
  • Page 46 Pump Manual Run Cycle Cold Delay In DMS models, when the pump powers on when the To run an extra (non-programmed) temperature is below 14°F (-10°C), there is a 15 minute lubrication cycle, push the Manual Start cold delay before the pump resumes running the button.

  • Page 47: Alarms

    Pump Alarms Any time a Fault or Warning occurs, a combination of LEDs illuminate to notify that there is a problem and to help identify the kind of Fault or Warning that has occurred. • Faults do not automatically clear. Warnings clear after a set time, if the condition is fixed. •...
  • Page 48 Pump Cycle / System fails to relieve Examine system to deter- Pressure pressure or a lubrication mine if you have a Warning cycle was not completed plugged or broken line or in the user-defined amount other component failure, of time. i.e., divider valve, injector.
  • Page 49 Pump System An internal fault has Contact Graco Customer Fault occurred. Service. Cycle / In pressure mode indicates Examine system to Pressure that unit is over pressur- determine if you have a Fault ized or a lubrication cycle plugged or broken line or...
  • Page 50 Examine pump to ensure permanent damage. that it is rotating properly. Pump tries running cycle If necessary, contact 90 times before shutting Graco Customer Service. down. See Pump Over-current Protection, page 18. Motor The measured motor Examine system to make...
  • Page 51 F to 158° F (-25° C to Use of the unit outside of 70°C). the recommended temperature range could If necessary contact cause degraded system Graco Customer Service. performance and possible damage. USB Error An error occurred during a Read the Troubleshooting DMS operation.

  • Page 52: Additional Fault/Warning Scenarios For

    Pump Additional Fault/Warning Scenarios for Firmware Versions 5.06 and Later for Non-DMS Models and 7.09 and later for DMS Models Alarm Type What it Looks Like What it Indicates Solution Low Power If there is a voltage drop at Check voltage and Warning the power source during available current output...

  • Page 53: Testing Installation

    Pump Testing Installation NOTE: Complete instructions for programming the Electric Grease Jockey pump begin on page 72. 1. Power up the pump and enter Setup Mode by pressing both the UP and DOWN ARROW buttons together for 3 seconds. 2. Button flashes green. 3.

  • Page 54: Manifold

    Manifold Manifold Parts: 12 port models There are two manifold sizes: • 6 port manifold - use in lubrication systems with 6 Part No Description or less lubrication points (F . 39 and F . 41). INJECTOR (see Injector • 12 port manifold - use in lubrication systems with 7 Parts, page 56) to 12 lubrication points (F...

  • Page 55: Manifold Dimensions

    Manifold Manifold Dimensions 6 Point Manifold Dimensions 12 Point Manifold Dimensions . 41 . 42 Injector Manifold Assembly Injector outputs can be combined for a common bearing point with a large grease requirement, but the output for a single injector cannot be split into multiple bearing points.

  • Page 56: Injectors

    Injectors Injectors Parts Part No Description SEAL, gasket BODY, injector CUP, retaining 556586 O-RING, 5-058 556660 NUT, sleeve assembly, 3/16 tube SPACER, output, model 24Z682; injector size #0 SPACER, output, model 24Z683; injector size #1 SPACER, output, model 24Z684; injector size #2 557898 SPACER, output, model 24Z685;...

  • Page 57: Adjust The Grease Output Volume

    Injectors Adjust the Grease Output Volume Grease injectors provide precise lubrication to each grease point in the system. If an injector is not producing the correct amount of lubricant for a specific location on the vehicle, or if a replacement injector of correct size is not available, output spacer washers (110) can be installed to adjust the injector output volume (F .

  • Page 58: Manifold Installation

    Injectors Manifold Installation For all injector adjustments: 2. Place the injector (101) in a vise with the outlet end • Mount all injector manifolds on the vehicle frame (tube connector) facing up. rail, or a cross member, close to the lubrication points.

  • Page 59: Modules

    Modules Modules NOTE: All installations may not include all of the points listed. The illustrations and instructions shown in the Modules section are provided for reference only. They may not be an exact representation of the truck or equipment. Lubrication points and locations are unique to each vehicle and installation will vary from vehicle to vehicle.
  • Page 60 Modules Installation Instructions 1. Tie wrap the 3-tube bundle, 2-tube bundle and (2-tube #2, if present) marked bundle together as a group. These follow the air brake line over the wheel area. 2. Use double-strap ties (Part No. 25C980) to attach the tube to the air brake line.
  • Page 61 Modules Front Right Module (F . 50) Recommended Lube Point Point No. Description Injector Size Tube Color Bundle Fitting P/N SPRING SHACKLE Orange 556638 Elbow 2-Tube #1 SPRING SHACKLE Black 556638 Elbow PLUG PLUG 15K783 St Elbow and 556644 CLUTCH C/SHAFT LH Black 2-Tube Connector...
  • Page 62 Modules Installation Instructions 1. Tie wrap the 3-tube bundle and 2-tube #2 marked bundle together as a group. These follow the air brake line over the wheel area. NOTE: Skip Step 1 if there is not a 2-tube #2 tube bundle required for the installation.
  • Page 63 Modules Tandem Axle Module (F . 52) Recommended Lube Point Point No. Description Injector Size Tube Color Bundle Fitting P/N PLUG PLUG “S” CAM Black 556638 Elbow 2-Tube Unmarked SLACK ADJUSTER Orange “S” CAM Black 2-Tube Unmarked SLACK ADJUSTER Orange SLACK ADJUSTER Orange 2-Tube...
  • Page 64 Modules Installation Instructions 1. Run each twin line to the brake slack adjuster and S cam following the air hoses from the control valve to the brake cams. This allows for enough slack in the lines for axle movement. 2. Use double-strap ties (Part No. 25C980) to attach tube to the air brake line.
  • Page 65 Modules 5th Wheel Module (F . 54) Point No. Description Injector Size Tube Color Bundle Recommended Fitting P/N FIFTH WHEEL PLATE Orange FIFTH WHEEL PIVOT Black 3-Tube FIFTH WHEEL PLATE Blue 556644 Connector or 556638 Elbow FIFTH WHEEL PLATE Blue 3-Tube FIFTH WHEEL PIVOT Black...

  • Page 66: Feed Line Tubes And Fittings

    Modules instructions beginning on page 59. system. Other tube lengths are available. Contact your local Graco distributor or Graco Customer Support for 1. Measure the approximate lengths of fluid line tubes assistance.

  • Page 67: Feed Line Fittings

    Feed Line Tubes and Fittings Feed Line Fittings 5. Make sure the tube is well seated into each fitting. Hand tighten the tube nut onto the injector and Straight Connector - Part No. 556644 tighten 1 full turn beyond hand tight. Do not over tighten (F .

  • Page 68: Main Line Hose

    Main Line Hose Main Line Hose Determine the Main Line Hose Lengths Temperature Hoses are available in three lengths. One end is crimped in the factory, the other end comes with a Do not exceed the fluid or ambient temperature reusable fitting.

  • Page 69: Main Line Hose Assembly

    Main Line Hose Main Line Hose Assembly 2. Cut the hose square with a fine-tooth hacksaw or a cut-off wheel (F . 64). SKIN INJECTION HAZARD A hose that has been crushed or damaged in the vise may leak. High pressure fluid leaks will pierce skin.
  • Page 70 Main Line Hose 5. Use a wrench to finish tightening the socket (a) until it bottoms out. Then back off 1/4 turn to 1/2 turn . 66). . 66 6. Secure the socket (a) in the vise. Lubricate the . 68 nipple (c) and threads liberally with grease.

  • Page 71: Main Line Fittings

    Main Line Hose Main Line Fittings Straight Connector - Part No. 129763 . 70 Elbow Connector - Part No. 129755 . 71 Tee Fitting- Part No. 129759 . 72 3A5082N...

  • Page 72: Start The System And Operation

    Start the System and Operation Start the System and Operation AUTOMATIC SYSTEM ACTIVATION HAZARD The system is equipped with an automatic timer that activates the pump lubrication system when power is connected or when exiting the programming function. Unexpected activation of the system could result in serious injury, including skin injection and amputation.
  • Page 73 Start the System and Operation 6. The pump rests (OFF time) for 2 hours and 53 minutes. NOTE: This the factory set OFF time. 7. The cycle repeats. NOTE: See Program the Pump, page 25 for instructions to increase or decrease cycle time. Typical Cycle The illustration shown in F .

  • Page 74: Troubleshooting

    Troubleshooting Troubleshooting Problem Cause Solution Too much grease at all lube points Lube cycle too frequent Increase pump OFF/rest time. Too much grease at one lube point Injector is leaking Remove and replace injector Not enough grease at all lube points Lube cycle is too infrequent Decrease pump OFF /rest time.
  • Page 75 Retry using a different flash USB Error 07 drive. If any of the above do not rectify the error, contact Graco Customer Service. Pump program setting file not found Verify that the pump program setting folder structure and file are stored correctly on the flash drive.
  • Page 76 Unplug the flash drive and reinstall. • Cycle power and re-install the All other USB errors flash drive. • Retry using a different flash drive. If any of the above do not rectify the error, contact Graco Customer Service. 3A5082N...

  • Page 77: Maintenance

    Maintenance Maintenance Frequency Component Required Maintenance Keep refill fitting clean by covering it Daily and at refill Refill Fitting with dust cap (26) when not in use. Clean refill fitting using a clean dry cloth. Dirt and/or debris can damage pump and/or lubrication system.

  • Page 78: Service Parts

    Service Parts Service Parts Part No. Description Illustration Lube Point Fittings Brakes, King Pins, Drag Links, Tie Rods, Spring Pins, 5th Wheel 556644 3/16 in. OD tube to 1/8 NPT straight connectors 556638 3/16 in. OD tube to 1/8 NPT elbows 15K740 1/4-28SAE (m) to 1/8 NPT (f)
  • Page 79 Service Parts Part No. Description Illustration Mainline Hose and Fitting 17S968 6 ft (1.8 m) Mainline cut-to-length hose and fitting 17S969 12 ft (3.7 m) Mainline cut-to-length hose and fitting 17S970 18 ft (5.5 m) Mainline cut-to-length hose and fitting 129763 Straight connector, 6 ORB x 9/16 37°...
  • Page 80 Service Parts Part No. Description Illustration Pump 24Z764 12 Volt Standard 24Z959 24 Volt Standard 24Z660 12 Volt, DMS and Illuminated Remote Run Button 24Z958 24 Volt, DMS and Illuminated Remote Run Button 26A848 24 Volt, DMS and Illuminated Remote Run Button, 1000 psi 26C494 12 Volt, DMS with follower 26C495...
  • Page 81 Service Parts Part No. Description Illustration 24Z681 #8, Grease Injector Meter, 5th Wheel Plate, Round on the Hex, Four Spacers 557898 Injector Spacers 25C988 Bare Manifold with Stem, Nut and Washer, Six port (bare Block) 25C989 Bare Manifold with Stem, Nut and Washer, 12 port (Bare Block) 24Z808...

  • Page 82: Technical Specifications

    Technical Specifications Technical Specifications Grease Jockey Automatic Lubrication System Metric 2000 psi 13.79 MPa, 137.9 bar Maximum fluid working pressure 1000 psi 6.89 MPa, 68.9 bar Fluid Grease NLGI 000 - #2 Grease Jockey Pump Pump Output Pressure 2000 psi 13.79 MPa, 137.9 bar Power 12 VDC...

  • Page 83: California Proposition 65

    Technical Specifications Grease Jockey Automatic Lubrication System Metric Injectors Maximum Operating Pressure 2000 psi 13.79 MPa, 137.9bar Minimum Operating Pressure 450 psi 3.2 MPa, 31.5 bar Reset Pressure 250 psi 1.72 MPa, 17.24 bar Output Volume per Cycle Size 0 injector 0.002 cu.

  • Page 84: Graco Ile On-Road Electric Grease Jockey (Egj) Warranty

    With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of sixty (60) months from the date of sale, repair or replace pump, pump element, injector meters and modules ("EGJ Parts") that are part of an ILE On-Road Electric Grease Jockey system, and only such EGJ Parts that are determined by...

This manual is also suitable for:

Jockey 24z959Jockey 24z660Jockey 23z958Jockey 26c494Jockey 25v619Jockey 26c495 ... Show all

Table of Contents