Advertisement
Quick Links
GB734V
INSTALLATION TOOL
GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE
E-MAIL US FOR A DISTRIBUTOR NEAR YOU.
GAGE BILT Inc.
GAGE BILT
44766 Centre Court
(586) 226-1500
Clinton Twp. MI 48038
(586) 226-1505 Fax
MADE IN U.S.A.
e-mail: solutions@gagebilt.com / www.gagebilt.com
Advertisement
Related Manuals for Gage Bilt GB734V
Summary of Contents for Gage Bilt GB734V
- Page 1 GB734V INSTALLATION TOOL GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR A DISTRIBUTOR NEAR YOU. GAGE BILT Inc. GAGE BILT 44766 Centre Court (586) 226-1500 Clinton Twp. MI 48038 (586) 226-1505 Fax MADE IN U.S.A. e-mail: solutions@gagebilt.com / www.gagebilt.com...
- Page 2 TABLE OF CONTENTS Description Page Warnings ........................... 3 Description, Operation and Maintenance ................4 Filling and Bleeding ....................... 5 Troubleshooting ........................6 Overhaul, Disassembly and Parts List ................7-8 ....................... 9 DEXRON® III Oil Safety Data Nose Assembly Selection Chart ................... 10 EU Conformity and Warranty ....................
- Page 3 73.2 DBA. In this daily basis for damage or wear. Any repair should condition the max level was 81.5 DBA. Therefore, it be done by qualified personnel trained on Gage Bilt is required where prolonged use, hearing procedures.
- Page 4 The GB734V riveter operates on a wide range of air pressure, with 90 to 100 psi providing the maximum efficiency. At 90 psi air pressure, the GB734V does not exceed 81.5 db (A) and consumes 3 cfm at 20 cycles a minute.
- Page 5 FILLING & BLEEDING PROCEDURE: WARNING DO NOT CYCLE TOOL WITHOUT AIR BLEEDER, OR THE SCREW AND STAT-O-SEAL, INSTALLED IN TOOL HEAD. SEVERE PERSONAL INJURY MAY RESULT. CAUTION BEFORE FILLING HANDLE, AIR PISTON SHOULD BE ALL THE WAY DOWN. `* FILLING & BLEEDING VIDEO AVAILABLE AT: www.gagebilt.com/bleeding.htm To replace a small amount of oil in the tool, attach the air bleeder and connect tool to air line.
- Page 6 OVERHAUL The disassembly and re-assembly procedure can be accomplished by utilizing the following instructions and drawings. Use extreme care during disassembly and re-assembly not to mar or nick any smooth surface that comes in contact with seals. Before installing seals, always apply a good lubricant, such as Lubriplate®, to the surfaces. It is recommended that tool kit (GB740TK) be used to facilitate overhaul.
- Page 7 HEAD Remove nose assembly and adapter from tool before attempting disassembly of head assembly. WARNING: DISPOSE OF HYDRAULIC FLUID IN ACCORDANCE WITH ALL ENVIRONMENTAL LAWS AND REGULATIONS APPLICABLE TO YOUR AREA. Remove end cap (734111-1). Push against threaded end of head piston (734107) to slide it out of head cylinder (734102).
- Page 8 HANDLE To inspect air cylinder bore, remove base cover (744124). Any further disassembly will require removal of the head cylinder (734102) first. For complete disassembly, start by removing base cover (744124). Next, holding tool upright, remove four button-head cap screws (402479). Lift head cylinder (734102) from handle (744129) and set aside o'ring (S832) and gasket (704129). Empty all hydraulic fluid into a container.
- Page 9 DEXRON® III OIL SAFETY DATA FIRST AID Skin: Wash thoroughly with soap and water as soon as possible. Casual contact requires no immediate attention. If irritation develops, consult a physician. Ingestion: Seek medical attention immediately. DO NOT INDUCE VOMITING. Eyes: Flush with copious amounts of water. If irritation develops, consult a physician. Inhalation: No significant adverse health effects are expected to occur on short term exposure.
- Page 10 XX-703-18V SEE CHART 20518 405371 10757 70820 SEE CHART SPRING ANVIL HOLDER COLLET CHART XX-734A-20V SEE CHART 10935 28819 400777 405371 70820 ANVIL HOLDER COLLET CHART O'RING CHART SPRING XX-743A-24V SEE CHART 10951 20867 50626 70820 ANVIL HOLDER COLLET CHART CHART SPRING RIVET...
- Page 11 CONFORMS TO THE FOLLOWING STANDARDS AND DIRECTIVES. EN292 part 1 and part 2 ISO 8662 part 1 ISO 3744 COUNCIL DIRECTIVE: 89/392/EEC, 91/368/EEC 93/44/EEC, 93/68/EEC EQUIPMENT DESCRIPTION: GB734V SERIES FASTENER INSTALLATION TOOLS MANUFACTURER: GAGE BILT Inc. SIGNATURE: NAME: BRIAN LEIGH PRODUCT MANAGER CLINTON TWP., MI U.S.A.