Table of Contents
Advertisement
Possible communication modes
l : Communication possible
―: Communication not possible
Setting
[AUTO]
[DIGITAL LINK]
[LONG REACH]
[ETHERNET]
*1 Communication via a twisted-pair-cable transmitter is not available. Connect the projector to the network directly.
Note
f For the signal with the resolution of 1 920 x 1 200 dots or less, the maximum transmission distance is 100 m (328'1") when connected with
the DIGITAL LINK communication method. For the signal with the resolution exceeding 1 920 x 1 200 dots, the maximum transmission
distance is 50 m (164'1").
f The maximum transmission distance when connected with the long-reach communication method is 150 m (492'2"). In this case, the signal
that the projector can receive is only up to 1080/60p (1 920 x 1 080 dots, dot clock frequency 148.5 MHz).
f If the communication method of the twist-pair-cable transmitter is set to long reach, the projector will connect with long-reach communication
method when the item is set to [AUTO]. To connect with the optional DIGITAL LINK Switcher (Model No.: ET-YFB200G) with the long-reach
communication method, set the item to [LONG REACH].
f Even when the item is set to [LONG REACH], connection will not be made correctly if the twist-pair-cable transmitter is not supporting the
long-reach communication method.
[DIGITAL LINK STATUS]
Display the DIGITAL LINK connection environment.
1)
Press as to select [DIGITAL LINK].
2)
Press the <ENTER> button.
f The [DIGITAL LINK] screen is displayed.
3)
Press as to select [DIGITAL LINK STATUS].
4)
Press the <ENTER> button.
f The [DIGITAL LINK STATUS] screen is displayed.
[LINK STATUS]
[HDCP STATUS]
[SIGNAL QUALITY]
[DIGITAL LINK MENU]
When the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G) is connected
to the <DIGITAL LINK/LAN> terminal, the main menu of the connected DIGITAL LINK output supported device is
displayed. Refer to the Operating Instructions of the DIGITAL LINK output supported device for details.
Chapter 4 Settings — [NETWORK] menu
Video transfer
(100 m (328'1"))
For DIGITAL LINK
For long reach
For Ethernet
The content of display is as follows.
[DIGITAL LINK]: Communicating in the DIGITAL LINK method.
[LONG REACH]: Communicating in the long reach method.
[ETHERNET]: Communicating in the Ethernet method.
[NO LINK]: Communication is not established.
One of [NO SIGNAL], [OFF], or [ON] is displayed.
The content of display is as follows.
[HDCP2.X]: When protected with HDCP 2.2 or HDCP 2.3
[HDCP1.X]: When protected with HDCP 1.X
[NONE]: When not protected with HDCP
[---]: When there is no signal
[SIGNAL QUALITY] is a numerical value of the amount of error, and the display color changes to
green, yellow, or red depending on that value.
Check the signal quality level while receiving a signal from the twisted-pair-cable transmitter.
f [MAX]/[MIN]: Maximum/minimum value of the amount of error
f Green (-12 dB or lower) → normal signal quality level.
f Yellow (-11 to -8 dB) → caution level that noise may appear on the screen.
f Red (-7 dB or higher) → abnormal level with interrupted synchronization and receiving not
possible.
Communication possible
Video transfer
(150 m (492'2"))
―
l
―
l
―
―
―
l
―
l
―
―
Ethernet
RS-232C
l
l
l
l
―
*1
l
l
l
l
l
―
*1
l
ENGLISH - 137
Advertisement
Table of Contents
