Download
Share
Print this page
Kinderkraft XPEDITION 2 i-Size User Manual
  1. Manuals
  2. Brands
  3. Kinderkraft Manuals
  4. Car Seat
  5. XPEDITION 2 i-Size
  6. User manual
Kinderkraft XPEDITION 2 i-Size User Manual

Kinderkraft XPEDITION 2 i-Size User Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
XPEDITION 2 i-Size
USER GUIDE
MODEL: XPEDITION 2 i-Size
ECE R129.03
v.1.0
MODEL: I-GUARD
ECE.R129.03
ver. 1.2

Advertisement

loading

Related Manuals for Kinderkraft XPEDITION 2 i-Size

Summary of Contents for Kinderkraft XPEDITION 2 i-Size

  • Page 1 XPEDITION 2 i-Size USER GUIDE MODEL: XPEDITION 2 i-Size ECE R129.03 v.1.0 MODEL: I-GUARD ECE.R129.03 ver. 1.2...
  • Page 2 CAUTION! The product graphics are for illustrative purposes only! Please carefully read the user manual before using the child car seat for the first time. Ensuring the safety of the child is your responsibility, and not reading this manual may have an impact on their safety. Usage The car seat has been designed, tested, and approved for use in accordance with the requirements of regulation No.
  • Page 3 attachment Height of the child Car seat orientation Car seat ISOFIX + Top Tether + inner harness straps 40-105 cm ISOFIX + Top Tether + inner harness straps 76-105 cm ISOFIX + 3-point safety harness 100 – 150 cm 3- point safety harness...

  • Page 4: Safety Instructions

    2.0 Safety instructions Please take a few minutes to read this user manual to ensure appropriate child's safety. • DO NOT install the car seat on seats facing backward or sideways to the direction of travel • DO NOT place the child’s car seat on seats equipped with an active front airbag.
  • Page 5 3.0 Securing the child 3.1 Inserting the insole The additional insole should be used until the child reaches 76 cm. 1.Connect the headrest section of the insole and its sides of to the inner section by using the fasteners 2.Unfasten the safety harness 3.Spread the belts to the sides of the seat 4.Insert the insole Head part of the insole...
  • Page 6 3.2 Securing the child with the inner harness straps 1.Loosen the harness straps all the way by pressing the button and pulling on the harness straps. Remember! Do not pull on the shoulder pads. 2.Unclip the safety harness 3.Place the harness straps on the sides of the seat 4.Place the child in the car seat 5.Adjust the headrest to your child's height 6.

  • Page 7: Tightening The Harness

    3.3 Tightening the harness 1.Pull on the inner straps to eliminate looseness in the hip section, the harness should lie flat. 2. Press the harness with the adjustment strap until the harness lies flat on the child's body. IMPORTANT: Make sure the harness straps are not twisted. Ensure that the straps are tightened so that there is no more than 1cm of space between them and the child.
  • Page 8 Adjust the appropriate height of the shoulder straps so that the belt enters the car seat’s backrest flat, horizontally just above the child's shoulders.

  • Page 9: Headrest Height

    3.3 Headrest height 1.Loosen the harness straps all the way by pressing the button and pulling the harness straps Remember! Do not pull on the shoulder pads. 2.Grasp the headrest height adjustment lever, which is located at the back of the headrest, and pull gently upwards 3.
  • Page 10 Seat tilt adjustment mechanism 1.Pull the seat tilt adjustment lever 2.Adjust the seat tilt angle 3.Release the lever in the required position (one of the four possible) 4.Gently move the seat until you hear a clear "click" sound CAUTION! In the later stages of installation, remember to loosen the Top Tether strap before adjusting the backrest tilt.
  • Page 11 CAUTION! When the car seat is facing forward, you can use 4 positions for adjusting the backrest. However, when the car seat is facing backward, you can only use 1 position for adjustment.
  • Page 12 3.5 Rotation mechanism The rotation mechanism is a feature that helps to comfortably position the child or remove them from the car seat. 1.Pull the seat rotation lever 2.Rotate the car seat in the direction you choose. You will hear a "click" indicating that the car seat is locked in the selected position.
  • Page 13 4.0 Assembly in the vehicle 4.1 ISOFIX installation 1. Attach the ISOFIX caps to the connectors of the car seat. 2. Place the Top Tether strap on the headrest, making sure not to obstruct access for future stages of car seat installation. 3.
  • Page 14 4.2 The „Top Tether” assembly 1.Pull out the upper securing strap (Top Tether). 2.Press the strap release button to loosen it (the length of the strap must allow you to attach the hook to the anchoring point located at the back of the vehicle seat or in the trunk).
  • Page 15 CAUTION! To use the rotation system, the Top Tether strap must be fitted on the inside of the vehicle (opposite side from the door).
  • Page 16 5.0 Hiding the 5-point safety harness 1.Loosen the safety harness completely by pressing the button and pulling the safety harness. Remember! Do not pull on the shoulder pads. 2.Remove the shoulder and buckle pads by unfastening the hoop&loop tapes located on the sides. 3.Place the headrest in the highest position.
  • Page 17 7. Pull out the foam located on the seat, and then remove the styrofoam cover underneath it. 8. Fasten the 5-point safety harness and tuck the fastened belts into the storage compartment so that they are laid flat along the backrest. 9.
  • Page 18 6.0 Car seat assembly Caution! The seat should be placed directly on the vehicle seat. 6.1 Children with a height between 40 to 105 cm using the ISOFIX system and the upper fixing strap („Top Tether”). 1.Install the car seat on the seat using the ISOFIX connectors, facing backward (if the car seat is already installed forward facing, rotate it using the rotation mechanism).
  • Page 19 6.2 Children with a height between 76 to 105 cm using the ISOFIX system and the upper fixing strap („Top Tether”). 1. Install the car seat on the seat facing forward, using the ISOFIX connectors. (If the car seat is already installed facing backward, rotate it using the rotational mechanism).
  • Page 20 6.3 Children with a height between 100 to 150 cm using the ISOFIX connectors and the vehicle’s 3-point safety belts. 1.Install the car seat on the seat using the ISOFIX connectors, facing forward. 2.Push the car seat as far as possible against the backrest of the seat and check for proper installation - the installation indicators should turn green.
  • Page 21 7.Fasten the snaps and cover the backrest of the car seat. 8.Thread the shoulder strap through the green shoulder strap guide. 9.Thread the car belt through both hip strap guides. Fasten the car belt. You will hear a characteristic "click."...
  • Page 22 6.4 Children with a height between 100 to 150 cm using the vehicle’s 3-point safety belts. 1.Install the car seat on the seat facing forward. 2.Push the car seat as far as possible against the backrest of the seat. 3.Uncover the shell of the car seat by detaching the snaps located on its edges.
  • Page 23 7.Fasten the snaps and cover the backrest of the car seat. 8.Thread the shoulder strap through the green shoulder strap guide. Thread the car belt through both hip strap guides. Fasten the car belt. You will hear a characteristic "click."...
  • Page 24 7.0 Disassembly of the car seat (ISOFIX installation system) 1.Loosen the Top Tether strap by pressing the release button and pulling the strap towards you. 2.Remove the securing hook from the vehicle's anchoring point. 3.Simultaneously press the ISOFIX release buttons on both arms of the ISOFIX connector (the color indicators should change to red).

  • Page 25: Cover Disassembly

    7.1 Cover disassembly 1.Remove the insole. 2.Loosen the safety belts completely by pressing the button and pulling the safety belts. Remember! Do not pull on the shoulder pads. 3.Adjust the headrest to the highest position. 4.Remove the shoulder pads and the cushion from the buckle. 5.Unfasten the four snaps securing the cover to the front part of the car seat backrest, as well as the snaps on the sides of the car seat.

  • Page 26: Cover Assembly

    7.Slide the cover off the front part of the seat, gently pulling the fabric from both sides. 8.Slide off the fabric from the car seat by passing it over the headrest. 7.2 Cover assembly To reinstall the cover simply reverse the above sequence of steps. Fit the cover to the attachment points on the seat.
  • Page 27 • Do not use aggressive cleaning agents (such as solvents). • The harness can be cleaned with lukewarm water and soap. Warning! Metal fasteners should never be removed from the straps. The full Warranty Terms and Conditions are available on the website WWW.KINDERKRAFT.COM...