Matrix / routing switcher series rs-232 protocol table (10 pages)
Summary of Contents for A-Neu Video ANI-PIP-44UHD
Page 1
ANI-PIP-44UHD 4x4 4K60 UHD HDR Quad/PiP/PoP Multiviewer Seamless Video Switcher PACKAGE CONTENTS Before attempting to use this unit, please check the packaging and make sure the following items are contained in the box: • 4K60 4x4 Seamless Matrix • 12V/2.5A Locking Power Adapter •...
Page 2
SAFETY INFORMATION To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference. Follow all instructions printed on unit chassis for proper operation. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid. Make sure power outlets conform to the power requirements listed on the back of the unit.
NEUVIDEO TABLE OF CONTENTS CONTENTS INTRODUCTION .................1 SAFETY PRECAUTIONS FEATURES / SPECIFICATIONS ..........2 Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. OPERATION CONTROLS & FUNCTIONS .........3 Please keep the following in mind as you unpack and install this IR REMOTE ..................5 equipment: IR CABLE PIN ASSIGNMENT &...
NEUVIDEO FEATURES & SPECIFICATIONS FEATURES • HDMI 2.0 and HDCP 2.2 compliant • Supports HDR • Video resolution is up to 4K@60Hz 4:4:4 • Supports 18Gbps lossless compressed video bandwidth • Supports 12 display categories in multi-viewer mode, and 9 splicing modes in video wall mode •...
NEUVIDEO OPERATION CONTROLS & FUNCTIONS FRONT PANEL LCD SCREEN: Display matrix switching status, input / output port, EDID, Baud rate, IP Address, etc. PWR INDICATOR: The LED is on green when the device is working. The LED is on red when the device is on standby. IR signal receiver.
Page 6
NEUVIDEO OPERATION CONTROLS & FUNCTIONS Rear Panel TCP/IP: TCP/IP control port, connected to PC or router with a CAT cable. RS-232 PORT: Connect to a PC or control system by D-Sub 9-pin cable to transmit RS-232 command. AUDIO INPUT (1~4): L/R analog audio input port, connected to an analog audio input source such as DVD or Blu-ray Player.
Page 7
NEUVIDEO Remote Control Remote Control POWER ON OR STANDBY: Power on the Matrix or set it to standby mode. INFO: Press to check the serial baud rate and IP address. It will be displayed in the top right corner of the screen, and disappear in five seconds or press the button again.
NEUVIDEO IR Cable Pin Assignment/ IR Control System IR Cable Pin Assignment IR Control System This product supports one-way IR control. When the matrix is connected to IR receiver cable and IR blaster cable, you can control the corresponding input source devices through IR signal transmission remotely at the side of display devices. Four IR blaster cables connected to the IR outputs must be placed near the four HDMI input sources.
NEUVIDEO LCD Displa y Na vigation LCD Displa y Na vigation The buttons on the the front panel are used for LCD display navigation, including INPUT(1~4), OUTPUT(1~4), MATRIX, MULTIVIEWER, VIDEOWALL, MENU, ENTER, UP, DOWN, POWER, LOCK. Menu items are as follows: LEVEL 1 LEVEL 2 LEVEL 3...
NEUVIDEO Video W all / Multi-Viewer Video W all The matrix supports 10 categories of display modes as below: User can select display modes via front panel buttons, Web GUI, and RS-232. Multi-Viewer The matrix supports 16 categories of multiview display modes: SINGLE, PIP, Dual, Triple 1, Triple 2, Triple 3, Quad 1, Quad 2, Quad 3, User 1, User 2, User 3.
NEUVIDEO EDID Management EDID Management This Matrix has 12 factory defined EDID settings, 2 user-defined EDID modes and 4 copy EDID modes. You can select defined EDID mode or copy EDID mode to input port through front panel buttons, RS-232 control or Web GUI. On-panel button operation: On the initial LCD display screen, press “MENU”...
Page 13
NEUVIDEO EDID Management The defined EDID setting list of the product is shown as below: EDID MODE EDID DESCRIPTION 4K60, 2.0CH 4K60, 5.1CH 4K60, 7.1CH 4K30, 2.0CH 4K30, 5.1CH 4K30, 7.1CH 1080P, 2.0CH 1080P, 5.1CH 1080P, 7.1CH WUXGA, 2.0CH 768P, 2.0CH XGA, 2.0CH USER1 USER2...
NEUVIDEO Web GUI User Guide Web GUI User Guide The Matrix can be controlled by Web GUI. The operation method is shown as below: Step 1: Get the current IP Address. The default IP address is 192.168.0.100. You can get the current Matrix IP address in two ways: The first way: You can get the IP address via IR remote.
Page 15
NEUVIDEO Web GUI User Guide Input Page You can do the following operations on the Input page: 1. Input: Input channel of the device. 2. Active: It indicates whether the channel is connected to a signal source. It is green if connected, and gray if not connected. 3.
Page 16
NEUVIDEO Web GUI User Guide Output Page You can do the following operations on the Output page: 1. Outputs: Output channel of the device. 2. Cable: It indicates the connection status of output ports. When the output port is connected to the display, it shows green. Otherwise, it shows gray.
Page 17
NEUVIDEO Web GUI User Guide 6. HDCP: Click the drop-down menu and set the HDCP version for current output. There are four options to be selected: • 1.4: HDCP 1.4 compliant. • 2.2: HDCP 2.2 compliant. • Follow Sink: HDCP version follows the corresponding display device. •...
Page 18
NEUVIDEO Web GUI User Guide CEC Page You can perform CEC management on this page. Inputs and Outputs can be controlled by clicking on the corresponding icons. 1. Input Control: Select the input source on the left, and then click on the icons to power on, power off, return, switch, pause, fast-forward, fast-back, mute, unmute, etc.
Page 19
NEUVIDEO Web GUI User Guide In matrix mode, you can select an output (1~4) firstly, and then select an input source (1~4) which will appear on the selected output area. One route of video output configuration is completed. Note: You can drag and drop any input source on the right to the corresponding output easily and quickly. 2.
Page 20
NEUVIDEO Web GUI User Guide If a user-defined mode is selected, you can do the following operations on this page: • The four windows are all displayed by default. • Each window can be dragged and zoomed at will. • Drag and drop the input source to any window. •...
Page 21
NEUVIDEO Web GUI User Guide Bind to Output: The AUDIO OUT (1~4) follows the HDMI OUTPUT (1~4). For example, if HDMI INPUT 2 is connected to HDMI OUTPUT 1, the audio of AUDIO OUT 1 is from HDMI INPUT 2; if HDMI INPUT 3 is connected to HDMI OUTPUT 1, the audio of AUDIO OUT 1 is from HDMI INPUT 3.
Page 22
NEUVIDEO Web GUI User Guide If the Mode is “Static”, you can set manually the IP Address/Gateway/Subnet/Telnet Port as required. If the Mode is “DHCP”, it will search and be filled with the IP Address assigned by the router automatically. You can’t modify it now. 2.
Page 23
NEUVIDEO Web GUI User Guide You can do the following operations on the System page: 1. Panel Lock: Click “ON/OFF” to lock/unlock panel buttons. “ON” indicates that panel buttons are unavailable; “OFF” indicates panel buttons are available. 2. Beep: Turn on/off the beep. 3.
NEUVIDEO RS-232 Control Command RS-232 Control Command The product also supports RS-232 control. You need a serial cable with RS-232 male head and DB9 transfer USB male head. The RS-232 head of the serial cable is connected to the RS-232 control port with DB 9 at the rear of the Matrix, and the USB head of the serial cable is connected to a PC.
Page 25
NEUVIDEO RS-232 Control Command COMMAND CODE FUNCTION DESCRIPTION EXAMPLE FEEDBACK DEFAULT s reboot! reboot the device s reboot! reboot… 4x4 hdmi seamless matrix system initializing... initialization finished! mcu fw version: x.xx.xx web gui: x.xx.xx s reset! reset to factory defaults s reset! reset to factory defaults 4x4 hdmi seamless matrix...
Page 26
NEUVIDEO RS-232 Control Command COMMAND CODE FUNCTION DESCRIPTION EXAMPLE FEEDBACK DEFAULT s output y csc x! x=3. ycbcr422 s output 1 csc 1! output 1 csc: rgb444 rgb444 x=4. ycbcr420 r output y csc! get output y color space r output 1 csc! output 1 csc: rgb444 status.(y=0~4) y=0.
Page 27
NEUVIDEO RS-232 Control Command COMMAND CODE FUNCTION DESCRIPTION EXAMPLE FEEDBACK DEFAULT s output y stream x! y=3. output 3 s output 1 stream 1! output 1 stream: enable enable y=4. output 4 x=0. stream disable x=1. stream enable r output y stream! get output y stream status r output 1 stream! output 1 stream: enable...
Page 28
NEUVIDEO RS-232 Control Command COMMAND CODE FUNCTION DESCRIPTION EXAMPLE FEEDBACK DEFAULT VIDEO MATRIX SETTING s output y in source x! route input source to s output 1 in source output1->input1 output1->input1 output y output2->input2 (y=0~4, x=1~4) output3->input3 y=0. output all output4->input4 y=1.
Page 29
NEUVIDEO RS-232 Control Command COMMAND CODE FUNCTION DESCRIPTION EXAMPLE FEEDBACK DEFAULT r tw group y source! y=1. tv wall group 1 r tw group 0 source! tv wall group 3 input: hdmi y=2. tv wall group 2 input 3 y=3. tv wall group 3 tv wall group 4 input: hdmi y=4.
Page 30
NEUVIDEO RS-232 Control Command COMMAND CODE FUNCTION DESCRIPTION EXAMPLE FEEDBACK DEFAULT s pip position x! set pip window position s pip position 3! pip on upper right pip on upper right (x=1~4) 1. upper left 2. lower left 3. upper right 4.
Page 31
NEUVIDEO RS-232 Control Command COMMAND CODE FUNCTION DESCRIPTION EXAMPLE FEEDBACK DEFAULT r mv output audio! get output audio source r mv output audio! output audio: follow window 1 selected source s mv res x! set multi-viewer resolution s mv res 3! multi-viewer resolution: 3840x2160p60 (x=1~15)
Page 32
NEUVIDEO RS-232 Control Command COMMAND CODE FUNCTION DESCRIPTION EXAMPLE FEEDBACK DEFAULT r output y exa! y=0. output all r output 1 exa! output 1 ext-audio: enable y=1. output 1 y=2. output 2 y=3. output 3 y=4. output 4 s output exa mode x! set output ext-audio s output exa output ext-audio...
Page 33
NEUVIDEO RS-232 Control Command COMMAND CODE FUNCTION DESCRIPTION EXAMPLE FEEDBACK DEFAULT s cec in x play! set input x play by cec, s cec in 1 play! input 1 play operation x=0~4 (0=all input) s cec in x pause! set input x pause by cec, s cec in 1 pause! input 1 pause operation x=0~4(0=all input)
Page 34
NEUVIDEO RS-232 Control Command COMMAND CODE FUNCTION DESCRIPTION EXAMPLE FEEDBACK DEFAULT r ip mode! get network ip mode r ip mode! ip mode: static s ip addr xxx.xxx.xxx. set network ip address s ip addr set ip address: xxx! 192.168.0.100! 192.168.0.100 (use “s net reboot!”...
Page 36
NEUVIDEO TERMS & CONDITIONS OF USE PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED BY, THROUGH OR UNDER A-NeuVideo, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your agreement to these Terms and Conditions.