Table of Contents
Advertisement
3-4. SERVICE Menu
The items required for maintenance of this unit such as the electrical adjustment, hours meter, or self-
diagnosis function of this unit are summarized in this SERVICE menu.
n
. The item may be not able to be selected in the menu item below by the current menu item setting.
. For the item that cannot be selected, "– – –" is displayed in the setting value.
Page
Menu
Item
S01
FUNCTION 2
MAG REL TIME
VF ASSIGN SW
MENU DISPLAY
AJC MODE
SECRET IND
S02
TEST
TEST1
COLOR SELECT
TEST LEVEL
TEST2
COLOR SELECT
TEST LEVEL
TEST3
*1: Refer to AUTO RELEASE of OPERATION MENU 03 MAGNIFICATION.
*2: Check whether the camera to be connected supports VF ASSIGNABLE SW.
*3: While the SERVICE menu is displayed, this item is disabled (menu display is not erased automatically).
*4: This item is available only for HDVF-EL70 and only when S800-2 on the PR-326 board is set to ON. (Refer to Section 1-3.)
*5: Necessarily operates in the OFF state when the power is turned on.
3-4
Setting (
is a factory-
Function
setting value.)
1 to
to 10
Sets the time required until returning from the expanded display
5
to the ordinary display when MAGNIFICATION AUTO RELEASE
is set to AUTO
LEFT,
Switches combination of switches that are settable for the
RIGHT
camera ASSIGNABLE switch
LEFT: ASSIGN.SW L1/L2 of the left handle is assigned.
RIGHT: ASSIGN.SW R1/R2 of the right handle is assigned.
, MANUAL
Sets menu display erasing method.
AUTO
AUTO:
MANUAL: Menu display is not erased automatically
, MODE2
Sets brightness correction mode of the panel module. MODE1
MODE1
is used normally.
, ON
Enables or disables the secret indicator.
OFF
OFF: Disabled
ON:
, BARS, SAW,
Sets the internal test signal on the input 1 side before scaling
OFF
RASTER, WINDOW
OFF:
BARS:
SAW:
RASTER: Outputs a rectangular test signal.
WINDOW: Outputs a window test signal.
, R, G, B, YL, CY, MG
Sets the display color during selection of RASTER or WINDOW
W
in TEST1.
0% to
to 109%,
Sets the signal level during selection of RASTER or WINDOW
100%
MAX
in TEST1.
, BARS, SAW,
Sets the internal test signal on the input 2 side before scaling
OFF
RASTER, WINDOW
OFF:
BARS:
SAW:
RASTER: Outputs a rectangular test signal.
WINDOW: Outputs a window test signal.
, R, G, B, YL, CY, MG
Sets the display color during selection of RASTER or WINDOW
W
in TEST2.
0% to
to 109%,
Sets the signal level during selection of RASTER or WINDOW
100%
MAX
in TEST2.
, BARS, SAW,
Sets the internal test signal after scaling
OFF
RASTER, WINDOW
OFF:
BARS:
SAW:
RASTER: Outputs a rectangular test signal.
WINDOW: Outputs a window test signal.
*1
.
*2
.
Menu display is erased automatically if no menu
operation is performed for about one minute after the
menu is displayed.
*3
Enabled
Outputs no test signal.
Outputs a color bars signal.
Outputs the test signal of a sawtooth waveform.
Outputs no test signal.
Outputs a color bars signal.
Outputs the test signal of a sawtooth waveform.
Outputs no test signal.
Outputs a color bars signal.
Outputs the test signal of a sawtooth waveform.
*4
*5
.
*5
.
*5
.
(Continued)
HDVF-EL70/HDVF-EL75
Advertisement
Table of Contents
