Tandon TM-100-1 Operating And Service Manual page 7

FIGURES
Figure
Number Title of Figure
LIST OF ILLUSTRATIONS
Page
Number
SECTION V - REPLACEMENT PROCEDURES
5-1 Drive Belt and Pulleys .................................................... 5-2
5-2 Logic PCBA Connectors and Mounting Screws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
5-3 Servo PCBA Connectors, Mounting Screws, and Spacers ........................ 5-4
5-4 Cone Lever Assembly Harnessing and Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
5-5 Cone Lever Assembly Harnessing, Mounting, and Stepper Motor Cables ............ 5-7
5-6 Cone Lever Assembly Cable Harness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
5-7 Cone Shaft and E-Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
5-8 Cone's Component Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 0
5-9 Activity LED Assembly Cable Harnessing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12
5-10 Activity LED Assembly Retaining Collar and LED Grommet ............. ... ... .... 5-13
5-11 Front Panel Bushings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14
5-12 Activity LED Assembly Retaining Collar and Grommet . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15
5-13 Front Panel Mounting Screws .............................................. 5-15
5-14 Front Panel Bushings and Locating Tabs ..................................... 5-17
5-15 Index Emitter Sensor Harnessing and Mounting ................................ 5-19
5-16 Index Detector Sensor Mounting Screw and Cable .............................. 5-20
5-17 Index Emitter and Index Detector Sensor Cables and Bundle ............. ......... 5-20
5-18 Drive Motor Assembly Harnessing and Mounting .......................... . .... 5-22
5-19 Drive Motor Assembly Pulley . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-23
5-20 Track 00 Switch Assembly Cable Harnessing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-24
5-21 Track 00 Switch Assembly E-Rings and Adjustment Screw ....................... 5-25
5-22 Track 00 Switch Assembly Mounting Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-25
5-23 Write Protect Switch Assembly Arm and Adjustment Screw . . . . . . . . . . . . . . . . . . . . . . . 5-27
5-24 Write Protect Switch Assembly Mounting Screw and Connector P8 . . . . . . . . . . . . . . . . . 5-28
5-25 Write Protect Switch Assembly Cable Harnessing .............................. 5-28
5-26 Nuts for Upper Arm and Spring Retainer ...................................... 5-30
5-27 Upper Arm Assembly Parts ................................. ... ............ 5-31
5-28 Felt Pad on Upper Arm ...................................... . ............ 5-31
5-29 Module Assembly Parts ....... . .......... .. ... . ........................... 5-32
5-30 Spindle Assembly Mounting Screw, Washer, and Pulley ......................... 5-34
5-31 Spindle Assembly Retainer and Hex Head Screws .............................. 5-35
5-32 Latch Plate Assembly Mounting Screws and Latch Inhibitor . . . . . . . . . . . . . . . . . . . . . . . 5-37
TABLES
Table
Number Title of Table
Page
Number
SECTION I- INTRODUCTION TO THE TM-100-1 AND-2 DISK DRIVES
1-1
1-2
1-3
Mechanical and Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Interface Connector Pin Assignments, J1 /P1 ........................... . ...... 1-12
Power Connector Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13
V