Kontron KBox E-120-EKL User Manual
  1. Manuals
  2. Brands
  3. Kontron Manuals
  4. Industrial PC
  5. KBox E-120-EKL
  6. User manual
Kontron KBox E-120-EKL User Manual

Kontron KBox E-120-EKL User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
USER GUIDE
KBox E-120-EKL
Doc. User Guide, Rev. 1.1
Doc. ID: [To be Determined]
www.kontron.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the KBox E-120-EKL and is the answer not in the manual?

Questions and answers

Related Manuals for Kontron KBox E-120-EKL

Summary of Contents for Kontron KBox E-120-EKL

  • Page 1  USER GUIDE KBox E-120-EKL Doc. User Guide, Rev. 1.1 Doc. ID: [To be Determined] www.kontron.com...
  • Page 2 KBox E-120-EKL - User Guide, Rev. 1.1 This page has been intentionally left blank www.kontron.com // 2...
  • Page 3 In cases of doubt, please contact Kontron. This user guide is protected by copyright. All rights are reserved by Kontron. No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means (electronic, mechanical, photocopying, recording, or otherwise), without the express written permission of Kontron.
  • Page 4 ENVIRONMENTAL DAMAGE (COLLECTIVELY, "HIGH RISK APPLICATIONS"). You understand and agree that your use of Kontron devices as a component in High Risk Applications is entirely at your risk. To minimize the risks associated with your products and applications, you should provide adequate design and operating safeguards.
  • Page 5 If you have any difficulties using this user guide, discover an error, or just want to provide some feedback, contact Kontron support. Detail any errors you find. We will correct the errors or problems as soon as possible and post the revised user guide on our website.

  • Page 6: Symbols

    KBox E-120-EKL - User Guide, Rev. 1.1 Symbols The following symbols may be used in this user guide DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury. WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.

  • Page 7: For Your Safety

    Therefore, in the interest of your own safety and of the correct operation of your new Kontron product, you are requested to conform with the following guidelines.

  • Page 8: Lithium Battery Precautions

    General Instructions on Usage In order to maintain Kontron’s product warranty, this product must not be altered or modified in any way. Changes or modifications to the product, that are not explicitly approved by Kontron and described in this user guide or received from Kontron Support as a special handling instruction, will void your warranty.

  • Page 9: Table Of Contents

    KBox E-120-EKL - User Guide, Rev. 1.1 Table of Contents Symbols .......................................... 6 For Your Safety ......................................7 High Voltage Safety Instructions ..................................7 Special Handling and Unpacking Instruction ..............................7 Lithium Battery Precautions ....................................8 General Instructions on Usage ................................8 Quality and Environmental Management ............................
  • Page 10 KBox E-120-EKL - User Guide, Rev. 1.1 4.3.3. M.2 Key B Socket ......................................25 4.3.4. M.2 Key E Socket ......................................25 4.3.5. M.2 Key M Socket ....................................... 25 4.3.6. Micro SIM Card Holder ..................................... 26 Accessing Internal Components .............................. 27 5.1.

  • Page 11: List Of Tables

    Figure 18: Removing the screws ..................................40 Figure 19: Securing the horizontal wall mount brackets ........................40 Figure 20: Securing the KBox E-120-EKL onto the mounting surface horizontally ..............41 Figure 21: Optional VESA mounting kit ................................41 Figure 22: Hole pattern of the base mounting kit ............................. 42 Figure 23: Securing the base mounting bracket ............................
  • Page 12 KBox E-120-EKL - User Guide, Rev. 1.1 Figure 28: BIOS Main Menu Screen System Data and Time ........................58 Figure 29: BIOS Advanced Menu ..................................60 Figure 30: BIOS Advanced Menu - Display Configuration ........................61 Figure 31: BIOS Advanced Menu - - Super IO Configuration ........................63 Figure 32: BIOS Advanced Menu - - Super IO Configuration - - Serial Port 1 Configuration ............

  • Page 13: 1/ General Safety Instructions For It Equipment

    Kontron is exempt from accident liability, this also applies during the warranty period. The product has been built and tested according to the basic safety requirements for low voltage (LVD) applications and has left the manufacturer in safety-related, flawless condition.
  • Page 14 KBox E-120-EKL - User Guide, Rev. 1.1 Additional safety instructions for DC power supply circuits  To guarantee safe operation of devices with DC power supply voltages larger than 60 volts DC or a power consumption larger than 240 VA, please observe that: ...

  • Page 15: Electrostatic Discharge (Esd)

    KBox E-120-EKL - User Guide, Rev. 1.1 1.1. Electrostatic Discharge (ESD) A sudden discharge of electrostatic electricity can destroy static-sensitive devices or micro-circuitry. Therefore proper packaging and grounding techniques are necessary precautions to prevent damage. Always take the following precautions: 1.
  • Page 16 KBox E-120-EKL - User Guide, Rev. 1.1 Do not dispose of lithium batteries in general trash collection. Dispose of the battery according to the local regulations dealing with the disposal of these special materials, (e.g. to the collecting points for dispose of batteries).

  • Page 17: 2/ Electromagnetic Compatibility

    Consult the dealer or an experienced radio/TV technician for help. Kontron is not responsible for any radio television interference caused by unauthorized modifications of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by Kontron.

  • Page 18: 3/ Shipment And Unpacking

    Kontron for help and information. 3.2. Scope of Delivery 3.2.1. Standard  1x KBox E-120-EKL (corresponding to the ordered system configuration)  1x Power adapter (power terminal block plug connector attached (It is attached on the system in case of not ordering power adapter.)) 1x Quick installation guide ...

  • Page 19: 4/ System Overview

    KBox E-120-EKL - User Guide, Rev. 1.1 4/ System Overview The KBox E-120-EKL is a fanless system enclosed within a robust compact aluminum chassis with cooling fins, offering the superior qualities for operation in harsh environments. It can be optionally factory-equipped with an M.2 Key B WWAN and /or M.2 Key E WLAN / Bluetooth card for two antennas.

  • Page 20: System Expansion Capabilities

    4.1.1. System Expansion via SATA Interface The baseboard comes with an onboard SATA 3.0 interface connector and a corresponding power connector. Users can expand the KBox E-120-EKL with a 2.5" SATA HDD / SSD drive. 4.1.2. System Expansion via M.2 Card Interface The baseboard comes with three onboard M.2 interface connectors with Key B Type 2242 / 2280, Key E Type 2230...

  • Page 21: Front I/O Panel

    KBox E-120-EKL - User Guide, Rev. 1.1 4.2. Front I/O Panel Figure 1: Front I/O Panel Figure 2: Rear I/O Panel 1 DC-In (see Chapter 4.2.1) 2 Power Button (See Chapter 4.2.2) 3 Power LED (see Chapter 4.2.3) 4 Standby LED (see Chapter 4.2.3) 5 Storage LED (see Chapter 4.2.4)

  • Page 22: Power Button

    An external (digital) display can be connected to this DP connector. 4.2.6. 2.5 GbE LAN The KBox E-120-EKL provides two 2.5 GbE LAN ports on the front I/O panel. These connectors are 2.5 Gigabit Ethernet 10/100/1000/2500 Mbit/s, IEEE 1588 capable interfaces. The connectors are standard 8-pin RJ45 type connectors with status LEDs: www.kontron.com...

  • Page 23: Usb 3.2 Gen 2

    USB 3.2 Gen 1 / USB 2.0 and allow connection of USB-compatible devices to the system. 4.2.8. USB 2.0 The KBox E-120-EKL provides two USB 2.0 interfaces on the front I/O panel and one USB 2.0 interface on the rear I/O panel. These connectors allow connection of USB-compatible devices to the system.

  • Page 24: Internal View

    KBox E-120-EKL - User Guide, Rev. 1.1 4.3. Internal View Figure 4: Internal View (without cover) 1 DDR4 SO-DIMM Memory Socket (DIMM1 & DIMM2, see Chapter 4.3.1) 2 SATA Data Connector (CN13, see Chapter 4.3.2) 3 SATA Power Output Wafer (CN10, see Chapter 4.3.2) 4 M.2 Key B Socket (M2B1, see Chapter 4.3.3)

  • Page 25: Ddr4 So-Dimm Memory Socket

    4.3.4. M.2 Key E Socket The KBox E-120-EKL reserves a M.2 Key E socket (Figure 4, pos. 5) with the support of PCIe x1, USB 2.0, SDIO, UART and C interfaces, allowing the expansion with a Type 22x30 M.2 WLAN, Bluetooth or combo module.

  • Page 26: Micro Sim Card Holder

    4.3.6. Micro SIM Card Holder The baseboard of the KBox E-120-EKL is equipped with a Micro SIM card holder to accommodate a Micro SIM card for WWAN service access. It is connected to UIM signals on the M.2 Key B socket.

  • Page 27: 5/ Accessing Internal Components

    KBox E-120-EKL - User Guide, Rev. 1.1 5/ Accessing Internal Components This section contains important information that you must read before accessing the internal components. You must follow these procedures properly when installing, removing or handling any board. It is recommended to expand your system with applicable expansion card(s) before it is installed into an equipment, machine or cabinet.

  • Page 28: Opening And Closing The Chassis

    Disconnect all peripherals. 2. The KBox E-120-EKL should lay on a flat, clean surface with the access cover facing upwards. 3. Loosen and remove the Phillips screws (six located on the access cover), that secure the access cover to the chassis.

  • Page 29: Figure 7: Lifting The 2.5'' Hdd / Ssd Bracket Up

    KBox E-120-EKL - User Guide, Rev. 1.1 Figure 7: Lifting the 2.5’’ HDD / SSD bracket up 1 2.5‘‘ HDD / SSD bracket 2 Screw Hole for Securing 2.5‘‘ HDD / SSD 6. Now you have access to the internal DDR4 SO-DIMM, SATA, M.2 Key B, M.2 Key E and Micro SIM Card slots / sockets respectively in order to remove or install hardware components.

  • Page 30: Figure 8: Unscrewing The Bottom Cover

    KBox E-120-EKL - User Guide, Rev. 1.1 Figure 8: Unscrewing the bottom cover 8. Loosen and remove the Phillips screws (five screws) that secure the baseboard to the chassis. Retain the screws for later use. Figure 9: Unscrewing the baseboard 9.

  • Page 31: Installing So-Dimm Memory Module(S)

    When used as intended, the KBox E-120-EKL is to operate only in closed condition. Only when the access cover is properly fixed with the screws and the front side with...

  • Page 32: Table 2: Fixing Bolt Extensions And Fastening Screw

    KBox E-120-EKL - User Guide, Rev. 1.1 1. Open the device as described in the subsection 5.1 "Opening and Closing the Chassis" (step 1 - 6). 2. Locate the M.2 Key B socket (M2B1) (Figure 4, pos. 4) and / or M.2 Key E socket (M2E1) (Figure 4, pos. 5) which you intend to use for installation as well as the corresponding fixing bolt(s) (Figure 4, pos.

  • Page 33: Installing A M.2 Key M Ssd

    6. After closing the cover, lock the cover by sliding the closed cover in the direction shown in Figure 11. Figure 11: Installing the Micro SIM card 7. In order to close the KBox E-120-EKL, proceed step 13 & 14 described in the subsection 5.1 "Opening and Closing the Chassis".

  • Page 34: 6/ Thermal Considerations

    The applied cooling method provides adequate cooling of the device during operation and performs a one-way thermal transfer to the chassis. Three sides of the KBox E-120-EKL consist of a compact aluminum U-shaped chassis are with cooling fins. The cooling fins provide heat dissipation during operation.
  • Page 35 KBox E-120-EKL - User Guide, Rev. 1.1 When the KBox E-120-EKL is extended and configured with third party components like M.2 expansion card(s) and hard drives (HDD or SSD), it has to be taken into account that the air temperature inside the system is higher than the ambient temperature.

  • Page 36: 7/ Installation Instructions

    Refer also to section 10.1 ‘‘Mechanical Specifications’’. The KBox E-120-EKL must be firmly attached to a clean flat and solid mounting surface. Use proper fastening materials suitable for the mounting surface. Ensure that the mounting surface type and the used mounting solution safely support the load of the KBox E-120-EKL and the attached components.

  • Page 37: System Mounting

    In order to adapt the KBox E-120-EKL for mounting, Kontron offers different mounting solutions such as:  KBox E-120-EKL configuration with a DIN rail mounting kit for vertical / horizontal installation into a control cabinet / custom enclosure / machine ...

  • Page 38: Figure 13: Securing The Adapter Plate

    4. Clip the top of the DIN rail clamp into the DIN rail and push the bottom of the DIN rail clamp firmly until it clamps onto the bottom of the DIN rail. Figure 15: Clamping the KBox E-120-EKL onto the DIN rail ...

  • Page 39: Horizontal Wall Mounting

    3 Keyhole Slot for Hanging the KBox E-120-EKL with a Screw 4 Screw Hole for Securing the Horizontal Wall Mount Bracket to the Chassis of the KBox E-120-EKL To mount the KBox E-120-EKL with the supplied horizontal wall mount brackets, the control cabinet / custom enclosure / machine / monitor / wall must have the screw pattern shown as Figure 17 for mounting.

  • Page 40: Figure 18: Removing The Screws

    Leave approximately 2 mm of clearance between the back of the screw head and the mounting surface. 5. Place the KBox E-120-EKL onto the mounting surface by placing the wide portion of each keyhole slot over the corresponding screw on the mounting surface.

  • Page 41: Vesa Mounting

    (Figure 21). The kit consists of two parts: a base bracket (Figure 21, pos. 1) to be fixed permanently on the mounting surface and another hooked bracket (Figure 21, pos. 2) to hold the KBox E-120-EKL with a hand-screw knob (Figure 21, pos.

  • Page 42: Figure 22: Hole Pattern Of The Base Mounting Kit

    Figure 23: Securing the base mounting bracket 3. Secure the hooked mounting bracket onto the bottom side of the KBox E-120-EKL (Figure 24) with M3 screws (6 mm long) via the VESA 100 mounting holes. The orientation depends on usage requirements, application scenarios and / or surrounding conditions.

  • Page 43: Figure 24: Securing The Hooked Mounting Bracket Onto The Kbox E-120-Ekl

    / scenarios / conditions. conditions. 4. Place the KBox E-120-EKL onto the mounting surface by sliding the hooked mounting bracket into the based mounting bracket (Figure 25). 5. Secure the hand-screw knob located on the hooked mounting bracket to fix two brackets (Figure 25).

  • Page 44: Dc Power Connection

    KBox E-120-EKL - User Guide, Rev. 1.1 7.2. DC Power Connection The KBox E-120-EKL is connected by a 2-pin terminal block socket connector (Figure 1, pos. 1) via a DC power supply wiring to a DC power source. The KBox E-120-EKL is delivered with a 2-pin terminal block plug connector (Figure 26). For DC connection, prepare the connecting wires using the supplied terminal block plug connector.

  • Page 45: 8/ Start Up

    8.1. Connecting to DC Power Supply The DC-In terminal block socket connector (Figure 1, pos. 1) is located on the front side of the KBox E-120-EKL. The KBox E-120-EKL will be connected to a DC main power supply via the supplied terminal block plug connector (Figure 26) and corresponding power wires (prepared as described in the subsection 7.2.1 "Cabling"), or to a AC-to-DC power...
  • Page 46 5. Press the power button (Figure 1, pos. 2) on the front panel to turn on the system. For connection to the supplied AC-to-DC power adapter in case of ordering the power adapter from Kontron: 1. Connect the power adapter cable with terminal block plug connector to the terminal block socket connector (DC IN, Figure 1, pos.

  • Page 47: Operating System And Hardware Component Drivers

    Your system can be supplied optionally with a pre-installed operating system. If you have ordered your KBox E-120-EKL with a pre-installed operating system, all drivers are installed in accordance with the system configuration ordered (optional hardware components). Your system is fully operational when you switch it on for the first time.

  • Page 48: 9/ Maintenance And Cleaning

    9/ Maintenance and Cleaning Equipment from Kontron requires only minimum servicing and maintenance for proper operation.  For light soiling, clean the KBox E-120-EKL with a dry cloth. Carefully remove dust from the surface of the chassis using a clean, soft brush. ...

  • Page 49: Technical Specifications

    KBox E-120-EKL - User Guide, Rev. 1.1 Technical Specifications Table 4: Technical Specifications System Processor  Intel® Atom® x6000E Series Processors  Intel® Celeron® J6000 / N6000 Series Processors  Intel® Pentium® J6000 / N6000 Series Processors Memory  2x DDR4 SO-DIMM...

  • Page 50: Mechanical Specifications

    KBox E-120-EKL - User Guide, Rev. 1.1 System Cooling Method  Passive Software OS Support  Windows 10, Linux 10.1. Mechanical Specifications Table 5: Mechanical Specifications Construction  Aluminum Metal Chassis Dimensions (W x D x H)  210 mm x 137.2 mm x 35 mm / 8.27’’ x 5.40’’ x 1.38’’...

  • Page 51: Environmental Conditions

    KBox E-120-EKL - User Guide, Rev. 1.1 10.2. Environmental Conditions Table 6: Environmental Conditions Operating Temperature  0 °C ~ 50 °C / 32 °F ~ 122 °F (Standard)  -20 °C ~ 70 °C / -4 °F ~ 158 °F (Extended) Storage Temperature ...

  • Page 52: 11/ Standard Interfaces - - Pin Assignments

    KBox E-120-EKL - User Guide, Rev. 1.1 11/ Standard Interfaces -- - Pin Assignments Low-active signals are indicated by a minus sign. 11.1. DC Power Input (Configuration 1) Table 8: DC Power Input (see Figure 1, pos. 1) Signal Name...

  • Page 53: Usb 3.2 Gen 2 Port

    KBox E-120-EKL - User Guide, Rev. 1.1 11.3. USB 3.2 Gen 2 Port Table 10: USB 3.2 Gen 2 Port (see Figure 1, pos. 8) USB 2.0 Contact Pin USB 3.2 Gen 2 9-pin USB Connector Type A Version 3.2 Gen 2 / 2.0...

  • Page 54: Dp Connector

    KBox E-120-EKL - User Guide, Rev. 1.1 11.5. DP Connector Table 12: DP Connector (see Figure 1, pos. 6) Signal Name DP Connector ML_Lane0p ML_Lane0n ML_Lane1p ML_Lane1n ML_Lane2p ML_Lane2n ML_Lane3p ML_Lane3n Config1 Config2 AUX_CHp AUX_CHn Hot_Plug DP_PWR 11.6. RS232/422/485 Serial Port Table 13: RS232/422/485 Serial Port (see Figure 2, pos.

  • Page 55: Digital I/O Port

    KBox E-120-EKL - User Guide, Rev. 1.1 11.7. Digital I/O Port Table 14: Digital I/O Port (see Figure 2, pos. 11) Signal Name DIO Port (9-pin D-SUB Female Connector) DIO_0 DIO_1 DIO_2 DIO_3 DIO_4 DIO_5 DIO_6 DIO_7 11.8. CAN Bus Connector Table 15: CAN Bus Connector (see Figure 2, pos.

  • Page 56: 12/ Bios

    Supervisor Password (see Security menu), press <RETURN>, and proceed with step 5. 5. A setup menu will appear. The KBox E-120-EKL uEFI BIOS setup program uses a hot key-based navigation system. A hot key legend bar is located on the bottom of the setup screens.

  • Page 57: Starting The Uefi Bios

    KBox E-120-EKL - User Guide, Rev. 1.1 12.2. Starting the uEFI BIOS The Setup utility features shows six menus in the selection bar at the top of the screen:  Main  Advanced  Power  Boot  Security ...

  • Page 58: Figure 28: Bios Main Menu Screen System Data And Time

    KBox E-120-EKL - User Guide, Rev. 1.1 Figure 28: BIOS Main Menu Screen System Data and Time Aptio Setup - AMI Main Advanced Power Boot Security Save & Exit Product Information Product Name KBox E-120-EKL BIOS Version 1.00 (x64) BIOS Build Date...

  • Page 59: Advanced Setup Menu

    KBox E-120-EKL - User Guide, Rev. 1.1 12.2.2. Advanced Setup Menu The Advanced setup menu provides sub-screens and functions for advanced configurations. The following sub- screen functions are included in the menu:  LAN & Audio Configuration  Display Configuration ...

  • Page 60: Figure 29: Bios Advanced Menu

    KBox E-120-EKL - User Guide, Rev. 1.1 Figure 29: BIOS Advanced Menu Aptio Setup - AMI Main Advanced Power Boot Security Save & Exit Onboard LAN1 Controller [Enabled] Onboard LAN2 Controller [Enabled] Load LAN1 UNDI Driver* [Disabled] Load LAN2 UNDI Driver**...

  • Page 61: Figure 30: Bios Advanced Menu - Display Configuration

    KBox E-120-EKL - User Guide, Rev. 1.1 Figure 30: BIOS Advanced Menu - Display Configuration Aptio Setup - AMI Main Advanced Power Boot Security Save & Exit Display Configuration Aperture Size [256MB] DVMT Pre-Allocated [32M] DVMT Total Gfx Mem [256M] →...
  • Page 62 KBox E-120-EKL - User Guide, Rev. 1.1 Feature Option Description [1366x768 1CH], [1366x768 2CH], [1600x1200 2CH], [1920x1080 2CH] LVDS Panel Color [18Bit], LVDS panel color depth by appropriate setup item. Depth [24Bit] PWM Backlight [By External], [By External]: Control by external HW circuit.

  • Page 63: Figure 31: Bios Advanced Menu - - Super Io Configuration

    KBox E-120-EKL - User Guide, Rev. 1.1 Figure 31: BIOS Advanced Menu - - Super IO Configuration Aptio Setup - AMI Main Advanced Power Boot Security Save & Exit Super IO Configuration > Serial Port 1 Configuration → ←: Select Screen >...

  • Page 64: Figure 32: Bios Advanced Menu - - Super Io Configuration - - Serial Port 1 Configuration

    KBox E-120-EKL - User Guide, Rev. 1.1 Figure 32: BIOS Advanced Menu - - Super IO Configuration - - Serial Port 1 Configuration Aptio Setup - AMI Main Advanced Power Boot Security Save & Exit Super Port 1 Configuration Serial Port [Enabled] →...

  • Page 65: Figure 33: Bios Advanced Menu - - Super Io Configuration - - Serial Port 2 Configuration

    KBox E-120-EKL - User Guide, Rev. 1.1 Figure 33: BIOS Advanced Menu - - Super IO Configuration - - Serial Port 2 Configuration Aptio Setup - AMI Main Advanced Power Boot Security Save & Exit Super Port 2 Configuration Serial Port [Enabled] →...

  • Page 66: Figure 34: Bios Advanced Menu - - Nvme Configuration

    KBox E-120-EKL - User Guide, Rev. 1.1 Figure 34: BIOS Advanced Menu - - NVMe Configuration Aptio Setup - AMI Main Advanced Power Boot Security Save & Exit NVMe Configuration No NVME Device Found → ←: Select Screen ↑ ↓: Select Item Enter: Select +/-: Change Opt.

  • Page 67: Figure 35: Bios Advanced Menu - - Sata Configuration

    KBox E-120-EKL - User Guide, Rev. 1.1 Figure 35: BIOS Advanced Menu - - SATA Configuration Aptio Setup - AMI Main Advanced Power Boot Security Save & Exit SATA Configuration SATA Controller(s) [Enabled] → ←: Select Screen SATA Mode Selection* [AHCI] ↑...

  • Page 68: Figure 36: Bios Advanced Menu - - Usb Configuration

    KBox E-120-EKL - User Guide, Rev. 1.1 Figure 36: BIOS Advanced Menu - - USB Configuration Aptio Setup - AMI Main Advanced Power Boot Security Save & Exit USB Configuration USB Devices: → ←: Select Screen 1 Keyboard ↑ ↓: Select Item...

  • Page 69: Figure 37: Bios Advanced Menu - - Trusted Computing

    KBox E-120-EKL - User Guide, Rev. 1.1 Figure 37: BIOS Advanced Menu - - Trusted Computing Aptio Setup - AMI Main Advanced Power Boot Security Save & Exit Configuration Security Device Support [Disable] NO Security Device Found → ←: Select Screen ↑...

  • Page 70: Figure 38: Bios Advanced Menu - - Pse Configuration

    KBox E-120-EKL - User Guide, Rev. 1.1 Figure 38: BIOS Advanced Menu - - PSE Configuration Aptio Setup - AMI Main Advanced Power Boot Security Save & Exit PSE Configuration Note: The Intel PSE only supports the Linux → ←: Select Screen...

  • Page 71: Figure 39: Bios Advanced Menu - - Network Stack

    KBox E-120-EKL - User Guide, Rev. 1.1 Figure 39: BIOS Advanced Menu - - Network Stack Aptio Setup - AMI Main Advanced Power Boot Security Save & Exit Network Stack [Disabled] IPv4 PXE Support* [Enabled] IPv6 PXE Support* [Disabled] → ←: Select Screen ↑...

  • Page 72: Figure 40: Bios Advanced Menu - - H/W Monitor

    KBox E-120-EKL - User Guide, Rev. 1.1 Figure 40: BIOS Advanced Menu - - H/W Monitor Aptio Setup - AMI Main Advanced Power Boot Security Save & Exit PC Health Status System Temperature : +35 C → ←: Select Screen...

  • Page 73: Figure 41: Bios Advanced Menu - - Dio Configuration

    KBox E-120-EKL - User Guide, Rev. 1.1 Figure 41: BIOS Advanced Menu - - DIO Configuration Aptio Setup - AMI Main Advanced Power Boot Security Save & Exit DIO Configuration User Configuration [Disabled] DIO_0* [Output High] DIO_1* [Output High] DIO_2*...

  • Page 74: Power Setup Menu

    KBox E-120-EKL - User Guide, Rev. 1.1 12.2.3. Power Setup Menu The Power setup menu provides functions and a sub-screen for power configurations. The following sub-screen function is included in the menu:  WatchDog Timer Configuration Figure 42: BIOS Power Setup Menu...

  • Page 75: Figure 43: Bios Power Setup Menu - - Watchdog Timer Configuration

    KBox E-120-EKL - User Guide, Rev. 1.1 Figure 43: BIOS Power Setup Menu - - WatchDog Timer Configuration Aptio Setup - AMI Main Advanced Power Boot Security Save & Exit WatchDog Timer Configuration WDT Function [Disabled] → ←: Select Screen...

  • Page 76: Boot Setup Menu

    KBox E-120-EKL - User Guide, Rev. 1.1 12.2.4. Boot Setup Menu The boot setup menu lists the for boot device priority order, that is generated dynamically. Figure 44: BIOS Boot Setup Menu Aptio Setup - AMI Main Advanced Power Boot Security Save &...

  • Page 77: Security Setup Menu

    The Security setup menu provides information about the passwords and functions for specifying the security settings. The passwords are case-sensitive. The KBox E-120-EKL provides no factory-set passwords. If there is already a password installed, the system asks for this first. To clear a password, simply enter nothing and acknowledge by pressing <RETURN>.

  • Page 78: Figure 46: Bios Security Setup Menu - - Secure Boot

    KBox E-120-EKL - User Guide, Rev. 1.1 Figure 46: BIOS Security Setup Menu - - Secure Boot Aptio Setup - AMI Main Advanced Power Boot Security Save & Exit System Mode Setup Secure Boot [Disabled] → ←: Select Screen Not Active ↑...

  • Page 79: Figure 47: Bios Security Setup Menu - - Secure Boot - - Key Management

    KBox E-120-EKL - User Guide, Rev. 1.1 Figure 47: BIOS Security Setup Menu - - Secure Boot - - Key Management Aptio Setup - AMI Main Advanced Power Boot Security Save & Exit Vendor Keys Valid Factory Key Provision [Disabled] >...
  • Page 80 KBox E-120-EKL - User Guide, Rev. 1.1 Feature Option Description [Delete] (b) EFI_CERT_X509 (DER) (c) EFI_CERT_RSA2048 (bin) Key Exchange Keys [Details], (d) EFI_CERT_SHAXXX [Export], 2. Authenticated UEFI Variable [Update], 3. EFI PE / COFF Image (SHA256) [Append], Key Source: Factory, External, Mixed...
  • Page 81 KBox E-120-EKL - User Guide, Rev. 1.1 12.2.5.1. Remember the password It is highly recommended to keep a record of all passwords in a safe place. Forgotten passwords results in being locked out of the system. If the system cannot be booted because the User Password or the Supervisor Password are not known, contact Kontron Support for further assistance.

  • Page 82: Save & Exit Setup Menu

    KBox E-120-EKL - User Guide, Rev. 1.1 12.2.6. Save & Exit Setup Menu The exit setup menu provides functions for handling changes made to the UEFI BIOS settings and the exiting of the setup program. Figure 48: BIOS Save & Exit Setup Menu...

  • Page 83: Appendix A: List Of Acronyms

    KBox E-120-EKL - User Guide, Rev. 1.1 Appendix A: List of Acronyms The following table does not contain the complete acronyms used in signal names, signal type definitions or similar. A description of the signals is included in the I/O Connector and Internal connector chapters within this user guide.

  • Page 84: About Kontron

    KBox E-120-EKL - - User Guide, Rev. 1.1 About Kontron Kontron is a global leader in IoT / Embedded Computing Technology (ECT) and offers individual solutions in the areas of Internet of Things (IoT) and Industry 4.0 through a combined portfolio of hardware, software and services.

Table of Contents