Philips 3100 CMF-AMF-OTC Service Manual page 42

Hide thumbs

Table Of Contents

Table of Contents

PHI 3100

IMPORTANT NOTE: If the DREGDRAWER is not inserted or the DOOR is

not closed the EV test cannot be performed. If these 2 inputs are not in

the right position, a warning message will be shown and the display turns

to yellow.

It is possible to hear the "click" from Electro Valve. The indication beside

the EV1 changes from "OFF" to "ON".

Press and Release the Z4 button to switch on the pump (100 impulses)

The water goes out from the pipe and the indication IMP shows increa-

sing numbers. The indication L/H must be within the range 10-18.

ERROR: The display backlight changes from green to red and the impulse

remains 0; If water comes out the pipe: check the wiring from the flow-

meter to the CPU/POWER board (JP5). If no water comes out the pipe:

check the pump and the wiring from the pump to the CPU/POWER board

(JP24).

ERROR : The L/H is zero or very low; the Electro Valve does not open.

Check the wiring from the Electro Valve to the CPU/POWER board (JP3)

and the Electro Valve.

The machine passes to the level 5 (Heater-Grinder)

1.6 Page 5 (Heater-Grinder)

Start condition

The grinder rotates and in the indication GRINDER the number increasing

up to 40. The other numbers inside the GRINDER box are not important

for this test.

ERROR: The number remains 0 or the grinder does not run, the display

backlight changes from green to red; check the Hall sensor board of the

Grinder, the Grinder, the wiring from the Hall sensor board to the CPU/

POWER board (JP2) and the wiring from the Grinder to the CPU/POWER

board (JP8)

Start condition

Press the Z1 button to open the Electro Valve

IMPORTANT NOTE: If the DREGDRAWER is not inserted or the

DOOR is not closed the EV test cannot be performed. If th

IMPORTANT NOTE: If the DREGDRAWER is not inserted or the

DOOR is not closed the EV test cannot be performed. If th

inputs are not in the right position, a warning message

DOOR is not closed the EV test cannot be performed. If th

inputs are not in the right position, a warning message

shown and the display turns to yellow.

inputs are not in the right position, a warning message

shown and the display turns to yellow.

It is possible to hear the "click" from Electro Valve. The

beside the EV1 changes from "OFF" to "ON".

It is possible to hear the "click" from Electro Valve. The

beside the EV1 changes from "OFF" to "ON".

The water goes out from the pipe and the indication

increasing numbers. The indication

The water goes out from the pipe and the indication

increasing numbers. The indication

10-18.

increasing numbers. The indication

10-18.

ERROR: The display backlight changes from green to red an

impulse remains 0; If water comes out the pipe: check the wi

ERROR: The display backlight changes from green to red an

impulse remains 0; If water comes out the pipe: check the wi

from the owmeter to the CPU/POWER board (JP5). If no wat

impulse remains 0; If water comes out the pipe: check the wi

from the owmeter to the CPU/POWER board (JP5). If no wat

comes out the pipe: check the pump and the wiring from th

from the owmeter to the CPU/POWER board (JP5). If no wat

comes out the pipe: check the pump and the wiring from th

to the CPU/POWER board (JP24).

comes out the pipe: check the pump and the wiring from th

to the CPU/POWER board (JP24).

ERROR : The L/H is zero or very low; the Electro Valve

open. Check the wiring from the Electro Valve to the CPU/

board (JP3) and the Electro Valve.

revNum

Press the Z7 button

revNum

The machine passes to the level 5 (Heater-Grinder)

1.6 Page 5 (Heater-Grinder)

Start condition

Press the Z4 button to switch on the grinder

The grinder rotates and in the indication

increasing up to 40. The other numbers inside the GRINDER

are not important for this test.

ERROR: The number remains 0 or the grinder does not run

display backlight changes from green to red; check the Ha

ERROR: The number remains 0 or the grinder does not run

display backlight changes from green to red; check the Ha

board of the Grinder, the Grinder, the wiring from t

display backlight changes from green to red; check the Ha

board of the Grinder, the Grinder, the wiring from t

board to the CPU/POWER board (JP2) and the wiring from t

board of the Grinder, the Grinder, the wiring from t

board to the CPU/POWER board (JP2) and the wiring from t

Grinder to the CPU/POWER board (JP8)

board to the CPU/POWER board (JP2) and the wiring from t

Grinder to the CPU/POWER board (JP8)

The number shows the heater temperature .

revNum

E. Urgese

Press the Z1 button to open the Electro Valve

Press and Release the

Z4 button to switch on the pump (100 impulses)

Press and Release the

Z4 button to switch on the pump (100 impulses)

Press and Release the

Z4 button to switch on the pump (100 impulses)

Press and Release the

Z4 button to switch on the pump (100 impulses)

L/H must be within the range

Test Mode Philips 3100

E. Urgese

Author

Veri ed

Author

Veri ed

Author

Veri ed

Author

Veri ed

Press the Z7 button

Test Mode Philips 3100

Press the Z4 button to switch on the grinder

GRINDER

the number

GRINDER

the number

GRINDER

the number

he Hall sensor

Check the temperature

E. Urgese

Author

Veri ed

05 SERVICE MODE

ese 2

will be

ese 2

will be

indication

IMP shows

d the

ring

d the

ring

e pump

Filename

e pump

Filename

20150423_Philips3100_TestMode_v01

does not

POWER

23/04/2015

Approved

23/04/2015

SaveDate

Approved

SaveDate

Approved

SaveDate

Approved

SaveDate

Filename

20150423_Philips3100_TestMode_v01

Filename

20150423_Philips3100_TestMode_v01

box

, the

ll sensor

, the

ll sensor

23/04/2015

Approved

SaveDate

23/04/2015

9/14

P/PP

6/9

10/14

P/PP

10/14

Table of Contents

Philips 3100 CMF-AMF-OTC Service Manual page 42

Related Manuals for Philips 3100 CMF-AMF-OTC

Related Products for Philips 3100 CMF-AMF-OTC

Table of Contents