Pioneer VSX-9500S VSX-7500S Operating Instructions Manual page 24

REAR PANEL FACILITIES
TAPE 1/DAT jacks
Connect a DAT (digital audio tape deck) or your primary analog cassette
deck to these jacks.
Connection for Recording
The tape recording jack (TAPE REC) on the cassette deck or DAT should
be connected to the REC side of the TAPE 1/DAT jack on the receiver
with a pin plug connecting cord.
Connection for Playback
Connect the TAPE PLAY jack on the cassette deck or DAT to the PLAY
side of the TAPE 1/DAT jack on the receiver with a pin plug connecting
cord.
(8) TAPE 2 jacks
Connect a second cassette deck to these jacks.
Connection for Recording
The tape recording jack (TAPE REC) on the cassette deck should be
connected to the REC side of the TAPE 2 jack on the receiver with a
pin plug connecting cord.
Connection for Playback
Connect the TAPE PLAY jack on the cassette deck to the PLAY side
of the TAPE 2 jack on the receiver with a pin plug connecting cord.
VIDEO jacks (input)
Connect the output jacks of video components.
For example, connect a playback-only VCR or a video camera.
@) TV jacks (input)
Use these jacks if wish to connect a TV tuner having both video and
audio outputs.
[VIDEO IN]
Connect the TV tuner's VIDEO OUTPUT to this jack.
[AUDIO IN (L, R))
Connect the TV tuner's AUDIO OUTPUT to these jacks.
VDP/CDV jacks
[VIDEO IN]
When playing back the audio channel from a LD player (VDP/CDV
player) or a VCR for playback, connect its AUDIO OUTPUT jacks here.
VCR 1 jacks
[VIDEO IN]
To receive the video image from VCR 1 used for playing, connect its
VIDEO OUTPUT jack here.
[AUDIO IN (L, R)}
To receive the audio channels from VCR 1 used for playing, connect
its AUDIO OUTPUT jacks here.
[VIDEO OUT]
When copying program material from the video component connected
to the VCR 2, VCR 3, VIDEO, VDP/CDV or TV jacks, connect to the
VIDEO INPUT jack of the VCR 1 used for recording.
[AUDIO OUT (L, R)]
VCR 2 jacks
[VIDEO IN]
[AUDIO IN (L, R)]
24
<ARB1173>
[VIDEO OUT]
When copying program materials from the video component connected
to the VCR 1, VCR 3, VIDEO, VDP/CDV or TV jack, connect to the
VIDEO INPUT jack of the VCR 2 used for recording.
[AUDIO OUT ({L, R)]
When copying program materials from the video component connected
to the VCR 1, VCR 3, VIDEO, VDP/CDV or TV jacks, or when recording
music from an audio component source, connect to the AUDIO INPUT
jacks of the VCR 2 used for recording.
@) VCR 3 input jacks
[VIDEO IN}
To receive the video image from a VCR used for playing only, connect
its VIDEO OUTPUT jacks here.
[AUDIO IN (L, R)]
To receive the audio channels from a VCR used for playing, connect
its AUDIO OUTPUT jacks here.
@) FRONT AMP jacks
[PRE-OUT]
When a separate power amplifier is used to drive the front speakers,
connect the power amplifier to these jacks.
[POWER IN]
When a separate pre-amplifier is connected and this unit is used as
power amplifier, connect the pre-amplifier to these jacks.
@ FRONT SPEAKERS terminals
A: Connect to a first set of speakers.
B: Connect to a second set of speakers.
Please refer to item @4) Front speakers impedance selector switch.
Front speakers impedance selector switch
Set this switch to match the impedance of your speakers.
position position
og, a
AORB_ J {._AORB;
40 TO LESS THAN 80 82 OR MORE
A + B; 8Q OR MORE
[1] When using one pair of speakers:
[i] When using two pairs of speakers:
Select @ as the selector switch position and use speakers having
impedance of 82 or more.
NOTE:
Turn off the receiver's power before changing the impedance selector
switch setting.
@) REAR SPEAKERS terminals
Connect the rear speakers to these terminals.
Speaker impedance
Connect speaker systems with a nominal impedance of between 8 and
162.
NOTE:
Do not allow any of the cord's conductors to protrude from the terminals
or touch any other conductors. Malfunctioning or breakdowns may
occur when conductors come into contact with each other.
AC Power cord
Connect to AC wall socket.