Pioneer VSX-9500S VSX-7500S Operating Instructions Manual page 23

REAR PANEL FACILITIES
@ FM/AM ANTENNA terminals
Use these antenna terminals for reception of normal FM and AM
broadcasts.
Attach the accessory AM Loop and FM T-type antennas, here.
* For details regarding antenna connection, see the section 'Hints for
Better Reception' on page 45.
@) GND terminal
Connect the turntable ground lead to this terminal.
(3) CONTROL IN, OUT jacks
Used for system control with other Pioneer components bearing the
Gi) mark.
IN... For connection from the CONTROL OUT jack of another
component.
OUT.... For connection to the CONTROL IN jack of another component.
NOTE:
The receiver's remote sensor does not function when a plug is inserted
in the IN jack. To operate, point the remote control unit at the remote
sensor on the component to which the receiver's IN jack is connected.
COM T ROL
i" 1
ie To the CONTROL
IN jack of the Pioneer
component bearing
the cr mark.
Receiver Pioneer component
bearing the (q| mark.
Remote control unit
@) SURROUND INPUT BALANCE control (DOLBY
SURROUND)
[VSX-7500S}
This knob is for adjusting the balance of the DOLBY SURROUND input
signal. To adjust, apply a monaural sound signal and rotate until the
SURROUND (rear) sound becomes minimal. {See page 31.)
[VSX-9500S]
Set the front panel PRO LOGIC CENTER MODE switch to the OFF
position. Play back a monaural source. Then adjust balance so that you
hear minimum volume from all channels. (See page 31.)
(©) MULTI-ROOM REMOTE IN jack.
When using the optional MR-100 adaptor for multi-room remote control,
connect to this jack.
(©) REAR AMP jacks
[PRE OUT}
When a separate power amplifier is used to drive the rear speakers,
connect the power amplifier to these jacks.
[POWER IN]
When a separate pre-amplifier is used for rear speakers and this unit
is used as a power amplifier, connect the pre-amplifier to these jacks.
@) CENTER AMP jacks
[POWER IN] (VSX-9500S only)
When a Separate pre-amplifier is used for center speaker and this unit
is used as a power amplifier, connect the pre-amplifier to this jack.
[PRE-OUT]
When a separate power amplifier is used to drive the center speaker,
connect the power amplifier to this jack.
CENTER SPEAKER terminal (VSX-9500S only)
Connect the center speaker here.
NOTE:
Use a center speaker with an impedance from 8 ohms to 16 ohms.
@ VIDEO ADAPTOR jacks
S (connector) video jacks
When used in conjunction with a VCR, VDP or monitor TV equipped
with S video jacks, connect to these jacks.
@) VIDEO OUT jacks
or VDP connected to this unit.
{TO MONITOR TV jack]
[TO RF MODULATOR jack]
the selected source on a conventional television set.
NOTE
a2 AC OUTLETS
[U.S. and Canadian models]
SWITCHED TOTAL 200 W MAX (VSX-9500S)
connected equipment should not exceed 200 W.
SWITCHED TOTAL 300 W MAX (VSX-7500S)
connected equipment should not exceed 300 W.
UNSWITCHED 200 W MAX
is switched ON or OFF. Electrical power consumption of the connected
equipment should not exceed 200 W.
[Multi-voltage model]
SWITCHED TOTAL 100 W MAX
connected equipment should not exceed 100 W.
UNSWITCHED 100 W MAX
is switched ON or OFF. Electrical power consumption of the connected
equipment should not exceed 100 W.
NOTE:
@ Audio INPUT jacks
PHONO ............... Connect to turntable.
CD assis cece teiniecediene Connect to compact disc player.
LINE oe catew andi 220i: Connect to the audio output jacks of an additional.
audio component.
23
<ARB1173>