Performer Profile Mini MKII 5600K Warning Unpacking Instructions Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure that all parts are present, and have been received in good condition. Notify the dealer immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs of mishandling.
Page 4
● If your Showtec device fails to work properly, discontinue the use immediately. Pack the unit securely (preferably in the original packing material), and return it to your Showtec dealer for service.
Performer Profile Mini MKII 5600K Operating Determinations ● This device is not designed for permanent operation. Consistent operation breaks will ensure that the device will serve you for a long time without defects. ● The minimum distance between light output and the illuminated surface must be bigger than 50 cm. ●...
Performer Profile Mini MKII 5600K The Performer can be placed on a flat stage floor or mounted to any kind of truss with a clamp. Connection with the mains Connect the device to the mains with the power-plug. Always check if the right color cable is connected to the right place. International EU Cable UK Cable...
Performer Profile Mini MKII 5600K Return Procedure Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued. Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility. Call Highlite 0031-455667723 or mail aftersales@highlite.com and request an RMA prior to shipping the...
Performer Profile Mini MKII 5600K Description of the device Features The Showtec Performer Profile Mini MKII 5600K is a compact theater spotlight fixture with high output. ● Input voltage: 110–240 V AC, 50/60 Hz ● Power consumption: 25 W ●...
Performer Profile Mini MKII 5600K Back Fig. 02 07) Manual dimmer control 08) Schuko power cable (1,4 m) 09) 3-pin DMX signal connector IN 10) 3-pin DMX signal connector OUT Installation Remove all packing materials from the Performer Profile Mini MKII 5600K. Check if all foam and plastic padding is removed.
Performer Profile Mini MKII 5600K Lens Locations The different lenses used in the Performer are not interchangeable. When installing a new tube lens, refer to the illustration below for proper placement. Fig. 03 Focusing the Beam 01) Loosen the beam focus controls located under the barrel (Fig. 04). 02) Slide the lens tube forwards or backwards to achieve the desired beam edge.
Performer Profile Mini MKII 5600K Color Frame Retaining Clip The color frame holder is equipped with a spring-loaded retaining clip. This prevents color frames and accessories from falling out (Fig. 06). Make sure that all color frame accessories are locked in position with the retaining clip before hanging the Performer.
Performer Profile Mini MKII 5600K Control Modes There are 2 modes: ● Manual Dimmer ● DMX-512/RDM Manual Dimmer (Control) 01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation. 02) Always use a safety cable (ordercode 70140 / 70141). 03) Plug the end of the electric mains power cord into a proper electric power supply socket.
Performer Profile Mini MKII 5600K Multiple Performers (DMX/RDM Control) 01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation. 02) Always use a safety cable (ordercode 70140 / 70141). 03) Use a 3-pin XLR cable to connect the Performers and other devices. 04) Link the units as shown in fig.
Performer Profile Mini MKII 5600K Fixture Linking You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to run synchronized shows of two or more fixtures set to a master/slave operating mode. The combined number of channels required by all the fixtures on a serial data link determines the number of fixtures the data link can support.
Performer Profile Mini MKII 5600K Cleaning Please follow the next recommendations when cleaning and inspecting lenses and reflectors: Do not use glass or window type cleaners on lenses (glass or polymer) or reflectors. Do not use abrasive materials such as steel wool. Replace lenses if they contain visible damage (cracks or deep scratches) which that may impair their effectiveness.
Suspect two potential problem areas as: the power supply and the LEDs. 01) Power supply. Check if the unit is plugged into an appropriate power supply. 02) The LEDs. Return the Performer to your Showtec dealer. 03) If both appear to be O.K., plug the unit in again.
Performer Profile Mini MKII 5600K Product Specifications Model: Showtec Performer Profile Mini MKII 5600K Input voltage: 110–240 V AC, 50/60 Hz Power consumption: 25 W Dimensions: 150 x 106 x 225 mm (LxWxH) Weight: 1,3 kg Electro-mechanical effects: Light source:...