Related Manuals for SHOWTEC Illumisphere 50
Summary of Contents for SHOWTEC Illumisphere 50
- Page 1 USER MANUAL ENGLISH Illumisphere 50 Product code: 41123 Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands...
- Page 2 Illumisphere 50 Preface Thank you for purchasing this Showtec product. The purpose of this user manual is to provide instructions for the correct and safe use of this product. Keep the user manual for future reference as it is an integral part of the product. The user manual shall be stored at an easily accessible location.
-
Page 3: Table Of Contents
Illumisphere 50 Table of contents Introduction ................................4 Before Using the Product ..........................4 Intended Use ............................... 4 Product Lifespan ..............................4 LEDs Lifespan ............................... 4 Text Conventions ..............................5 Symbols and Signal Words ..........................5 Symbols on the Information Label ........................5 Safety .................................. - Page 4 Illumisphere 50 Deinstallation, Transportation and Storage ....................26 Instructions for Deinstallation ..........................26 Instructions for Transportation ........................26 Storage ................................26 10. Disposal ................................26 11. Approval ................................26 Product code: 41123...
-
Page 5: Introduction
After unpacking, check the contents of the box. If any parts are missing or damaged, contact your Highlite International dealer. Your shipment includes: ● Showtec Illumisphere 50 ● 1 x non-detachable power cable to Schuko (1 m) ● 2 x non-detachable DMX cables with 3-pin DMX IN/OUT connectors (0,8 m) ●... -
Page 6: Text Conventions
Illumisphere 50 Text Conventions Throughout the user manual the following text conventions are used: ● Buttons: All buttons are in bold lettering, for example “Press the UP/DOWN buttons” ● References: References to chapters are in bold lettering, for example: “Refer to 2. Safety”... -
Page 7: Safety
Illumisphere 50 Safety Important Read and follow the instructions in this user manual before installing, operating or servicing this product. The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual. Warnings and Safety Instructions... - Page 8 Illumisphere 50 WARNING Risk of burns due to hot surface The inner parts of the device can become hot during operation. ● Allow the device to cool down for at least 15 minutes before servicing. WARNING Risk of epileptic shock Strobe lighting can trigger seizures in photosensitive epilepsy.
-
Page 9: Requirements For The User
Illumisphere 50 Attention Before each use, examine the device visually for any defects. Make sure that: ● All screws used for installing the device or parts of the device are tightly fastened and are not corroded. ● The safety devices are not damaged. -
Page 10: Description Of The Device
Illumisphere 50 Description of the Device The Showtec Illumisphere 50 is a decorative RGBW light effect. Overview Fig. 02 01) Non-detachable power cable to Schuko (1 m) 02) Non-detachable DMX cable (0,8 m) with a 3-pin DMX IN connector 03) Non-detachable DMX cable (0,8 m) with a 3-pin DMX OUT connector... -
Page 11: Product Specifications
Illumisphere 50 Product Specifications Model: Illumisphere 50 Electrical: Input voltage: 100–240 V AC, 50/60 Hz Power consumption: 100 W (max) Fuse: 3 A, 250 V Physical: Dimensions: Ø 500 mm (D) Weight: 3,6 kg Optics: Light source: 462 x SMD 5050 RGBW LEDs Dimmer: 0–100 %... -
Page 12: Dimensions
Illumisphere 50 Dimensions Fig. 04 Product code: 41123... -
Page 13: Installation
Illumisphere 50 Installation Safety Instructions for Installation WARNING Improper installation can cause serious injuries and damage of property. If trussing systems are used, installation must be carried out only by instructed or skilled persons. Follow all applicable European, national and local safety regulations concerning rigging and trussing. -
Page 14: Connecting To Power Supply
Use a suitable suspension chain or cable to hang the device. Make sure that the suspension cable/chain can hold 10 times the weight of the Illumisphere 50. Fasten the suspension chain/cable onto the cable suspension eyelet (08), see Fig. 05. -
Page 15: Setup
Disconnect power supply when connecting or disconnecting data cables. Stand-alone Setup When the Illumisphere 50 is not connected to a controller or to other devices, it functions as a stand- alone device. It can be operated in auto mode or sound-controlled mode. -
Page 16: Dmx Cables
Fig. 06. Fig. 06 Master/Slave Setup The Illumisphere 50 supports master/slave control mode. To connect multiple devices in a master/slave setup, follow the steps below: Connect the first device’s DMX OUT connector to the second device’s DMX IN connector. You can use an extension cable in case the non-detachable cables are too short. -
Page 17: Dmx Linking
Continue assigning the starting addresses of the remaining devices by adding each time 8 to the previous number. Make sure that you do not have any overlapping channels in order to control each Illumisphere 50 correctly. If two or more devices are addressed similarly, they will work similarly. -
Page 18: Operation
Control Modes The Illumisphere 50 can be operated with a lighting controller or without a controller in stand-alone mode. The Illumisphere 50 supports the following control modes: ●... -
Page 19: Control Panel
Illumisphere 50 Control Panel A) OLED display Sound-controlled mode indication LED (green) C) ENTER button D) DOWN button UP button MENU button G) DMX control mode indication LED (red) Fig. 09 ● Use the UP/DOWN buttons to navigate through the menus or to increase/decrease numeric values. -
Page 20: Menu Overview
Illumisphere 50 Menu Overview Product code: 41123... -
Page 21: Main Menu Options
Illumisphere 50 Main Menu Options The main menu has the following options: Press the UP/DOWN buttons to navigate through the main menu. 02) Press the ENTER button to open the menus. DMX Address In this menu you can set the device’s DMX starting address. -
Page 22: Settings
000–100, from low to high sensitivity ● DMX Fail: The device’s behavior in case of a DMX error. There are 2 options: Hold (the Illumisphere 50 will use the last properly received DMX signal which ensures undisrupted performance) and OFF (output blackout) ● Calibration: See 6.6.5.1. -
Page 23: Dmx Channels
Illumisphere 50 DMX Channels Function Value Setting Master dimmer 000–255 From low to high intensity (0–100 %) 000–255 From low to high intensity (0–100 %) Green 000–255 From low to high intensity (0–100 %) Blue 000–255 From low to high intensity (0–100 %) White 000–255... -
Page 24: Troubleshooting
Illumisphere 50 Troubleshooting This troubleshooting guide contains solutions to problems which can be carried out by an ordinary person. The device does not contain user-serviceable parts. Unauthorized modifications to the device will render the warranty void. Such modifications may result in injuries and material damage. -
Page 25: Maintenance
Illumisphere 50 Maintenance Safety Instructions for Maintenance DANGER Electric shock caused by dangerous voltage inside Disconnect power supply before servicing or cleaning. WARNING Risk of burns due to hot surface Allow the device to cool down for at least 15 minutes before servicing or cleaning. -
Page 26: Basic Cleaning Instructions
Illumisphere 50 Basic Cleaning Instructions The Illumisphere 50 requires almost no maintenance. However, you should keep the device clean. To clean the device, follow the steps below: Disconnect the device from the electrical power supply. Allow the device to cool down for at least 15 minutes. - Page 27 Illumisphere 50 Deinstallation, Transportation and Storage Instructions for Deinstallation WARNING Incorrect deinstallation can cause serious injuries and damage of property. ● Let the device cool down before dismounting. ● Disconnect power supply before deinstallation. ● Always observe the national and site-specific regulations during deinstallation and derigging of the device.
- Page 28 ©2020 Showtec...