Page 2
1. The changes or modifications not expressly approved by the party responsible for com- are the properties of the respective owners. pliance could void the user’s authority to operate the equipment. 2. Shielded interface cables must be used in order to comply with the emission limits. User's Manual | EC543-CS...
Serial Port Console Redirection ...................27 USB Configuration ......................28 CSM Configuration ......................28 USB Power Control ......................29 Network Stack Configuration..................29 Chipset ..........................30 Graphics Configuration ....................30 PEG Port Configuration ....................31 PEG Port Configuration ► PEG Port Feature Configuration ........ 31 User's Manual | EC543-CS...
Page 4
The manual is subject to change and update without notice, and may be based on editions that do not resemble your actual products. Please visit our website or contact our sales representa- • 1 EC543-CS system unit tives for the latest editions. •...
Page 5
Make sure the system is placed or mounted correctly and stably to prevent the chance of dropping or falling may cause damage. • The openings on the system shall not be blocked and shall be kept in distance from User's Manual | EC543-CS...
Reset Button HDMI/DP++ Combo Port 1 USB 2.0 Mic-In/ Line-Out (Auto Detection) Remote Switch HDMI/DP++ Combo Port 2 COM Ports Expansion Slots USB 2.0 (Auto Detection) USB 3.1 LAN 3~6 COM Ports LAN 1 & LAN 2 User's Manual | EC543-CS...
HDMI/DP++ Combo Port 2 HDMI/DP++ Combo Port 2 COM Ports (Auto Detection) Expansion Slots USB 2.0 (Auto Detection) USB 3.1 Storage Driver Bay USB 3.1 COM Ports LAN 1 & LAN 2 Mic-In/ Line-Out LAN 1 & LAN 2 User's Manual | EC543-CS...
USB 3.1 Gen2 USB 3.1 Gen1 the port as illustrated here. The insertion is fairly effortless and please reframe from forcing the insertion to prevent damage. LAN 1 & LAN 2 User's Manual | EC543-CS...
Audio Codec ALC888 ETHERNET 1 x Intel I210AT PCIe (10/100/1000Mbps) ® Controller 1 x Intel I219LM with iAMT11.0 PCIe (10/100/1000Mbps) (only Core i7/i5 supports iAMT) ® Interface RJ-45 1 x Status LED Indicators 1 x HDD LED User's Manual | EC543-CS...
Page 11
System reset, programmable via software from 1 to 255 seconds SECURITY TPM 2.0 POWER Type Wide range 9~36V 3-pole terminal block Connector 2-pin power extension switch connector OS SUPPORT Microsoft Windows 10 IoT Enterprise 64-bit Linux Linux (available upon request) User's Manual | EC543-CS...
Page 12
-20 to 60°C (SSD or mSATA) Storage Temperature -20 to 85°C Relative Humidity 5 to 95% RH (non-condensing) STANDARDS AND Shock Half sine wave 3G, 11ms, 3 shock per axis CERTIFICATIONS Vibration IEC68-2-64 Certifications CE, FCC Class A, UKCA User's Manual | EC543-CS...
There are 6 screws on both front and rear sides of the system and 6 screws on the left and right sides of the system used to secure the cover to the chassis. Remove the screws and put them in a safe place for later use. Left View Front View Right View Rear View User's Manual | EC543-CS...
Page 14
Chapter 2 HARDWARE INSTALLATION Step 2: Step 3: Turn the system upside down and lift the cover to open the system. The boards can be easily accessed after the chassis cover is removed. User's Manual | EC543-CS...
Screw tight the card onto the stand-off with a screw driver and a stand-off screw until the gap between the card and the stand-off closes up. The card should be lying parallel to the board when it’s correctly mounted. User's Manual | EC543-CS...
There are antenna holes reserved on both the right and left sides of the system and by default covered by rubber plugs. Please remove the plug prior to installing an antenna. Module Connector Cable Antenna Connector Washer User's Manual | EC543-CS...
Locate the drive bay on the front. Step 2: Pull the silver latch to unlock the door. Important: Excessive force may damage its mechanical parts. If the HDD/SSD is inserted backward into the slot, forcing the device may damage the slot. User's Manual | EC543-CS...
To install an expansion card, you need to first remove the chassis cover and turn the thumb screw counterclockwise to disassemble the slot plates and bracket. PCI card Thumb screw Slot plates Note: Supports up to 200mm in length of standard expansion cards. User's Manual | EC543-CS...
Locate the mount- ing holes on the bottom of the system as shown in the photo. Screw on the two brackets onto the system with six screws as illustrated below. Wall Mount Bracket Wall Mount Bracket User's Manual | EC543-CS...
When “X” appears on the left of a particular field, it indicates that a submenu which contains additional options are available for that field. To display the submenu, move the highlight to that field and press <Enter>. User's Manual | EC543-CS...
The time format is <hour>, <minute>, <second>. The time is based on the 24-hour military-time clock. For example, 1 p.m. is 13:00:00. Hour displays hours from 00 to 23. Minute displays min- utes from 00 to 59. Second displays seconds from 00 to 59. User's Manual | EC543-CS...
The system automatically powers on after power failure. S5 State The system enter soft-off state after power failure. Power-on signal input is required to power up the system. Last State The system returns to the last state right before power failure. User's Manual | EC543-CS...
When disabled, ME will not be unconfigured on RTC Clear. Enable or disable CPU Power Management. It allows CPU to enter "C states" when it’s idle and nothing is executing. Firmware Update Configuration Configurate firmware update Note: The sub-menus are detailed in following sections. User's Manual | EC543-CS...
Set SuperIO WatchDog Timer Timeout value. The range is from 0 (disabled) to 255. To clear the existing TPM encryption, select "TPM Clear" and restart the system. This field is not available when "Security Device Support" is disabled. Note: The sub-menus are detailed in following sections. User's Manual | EC543-CS...
Serial Port Serial Port Enable or disable serial port. Enable or disable serial port. Electrical Interface Mode Electrical Interface Mode Choose mode between RS232 / RS485 / RS422 Choose mode between RS232 / RS485 / RS422 User's Manual | EC543-CS...
This section displays the system’s health information, i.e. voltage readings, CPU and system temperatures, and fan speed readings Serial Port Enable or disable serial port. Electrical Interface Mode Choose mode between RS232 / RS485 / RS422 User's Manual | EC543-CS...
SYS Smart Fan/CPU Smart Fan Control = [Disabled] • Fix Fan Speed Count Set the fan speed, the value ranging from 1-100%, 100% being full speed. The fans will always operate at the specified speed regardless of gauged temperatures. User's Manual | EC543-CS...
Keep USB devices available only for EFI applications. • Auto Disable Legacy support if no USB devices are connected. XHCI Hand-off Enable or disable XHCI Hand-off. USB Mass Storage Driver Support Enable or disable USB Mass Storage Driver Support. User's Manual | EC543-CS...
Set the wait time in seconds to press ESC key to abort the PXE boot. Use either +/- or numeric keys to set the value. Media detect count Set the number of times the presence of media will be checked. Use either +/- or numeric keys to set the value. User's Manual | EC543-CS...
X Chipset Chipset Graphics Configuration Primary Display Select which of IGFX/PEG/PCI Graphics device to be the primary display. Internal Graphics Keep IGFX "Enabled" or "Disabled" based on the setup options, or select "Auto" for auto-detec- tion. User's Manual | EC543-CS...
PEG Port Configuration PEG Port Configuration ► PEG Port Feature Configuration Detect Non-Compliance Device Enable Root Port Detect Non-Compliance PCI Express Device in PEG Enable/Disable the Root Port Max Link Speed Configure PEG 0:1:0 Max Speed User's Manual | EC543-CS...
Assign the maximum value of Top Of Lower Usable DRAM (TOLUD). Select to specify a fixed value, or select "Dynamic" so that the assignment would adjust TOLUD automatically based on largest MMIO length of installed graphic controller. User's Manual | EC543-CS...
This option allows you to create RAID or Intel Rapid Storage configuration along with Intel® Optane™ system acceleration on Serial ATA devices. Ports and Hot Plug Enable or disable the Serial ATA port and its hot plug function. User's Manual | EC543-CS...
Chapter 3 BIOS SETTINGS Chipset PCH-IO Configuration ► HD Audio Configuration HD Audio Control the detection of the HD Audio device. Disabled HDA will be unconditionally disabled. Enabled HDA will be unconditionally enabled. User's Manual | EC543-CS...
Secure Boot. Press Enter and a prompt will show up for you to confirm. Reset To Setup Mode Clear the database from the NVRAM, including all the keys and signatures installed in the Key Management menu. Press Enter and a prompt will show up for you to confirm. User's Manual | EC543-CS...
Select this option to save BIOS configuration settings to a USB flash device. ► Restore Setting from file This field will appear only when a USB flash device is detected. Select this field to restore set- ting from the USB flash device. User's Manual | EC543-CS...
MAC address should be burned or not. c. After updating unique MAC Address from manufacturing, NVM will be protected immediately after power cycle. Users cannot update NVM or MAC address. User's Manual | EC543-CS...