Related Manuals for DFI EC543-CS
Summary of Contents for DFI EC543-CS
- Page 1 Quick Installation Guide EC543-CS Modular-Designed Embedded System www.dfi.com Package Contents • 1 EC543-CS system unit • 1 M.2 slot screw • 1 terminal block 3-pole for DC input • 1 cable with 2 wire stripped and tinned to DC jack © August 21, 2023 DFI Inc.
-
Page 2: Product Overview
Product Overview Front View Status/HDD LED Power Button Reset Button USB 2.0 Remote Switch COM Ports Quick Reference | EC543-CS... - Page 3 Rear View EC543-CS6G86-Q DC-in Grounding Storage Driver Bay HDMI/DP++ Combo Port 1 Mic-In/ Line-Out (Auto Detection) HDMI/DP++ Combo Port 2 Expansion Slots USB 2.0 (Auto Detection) USB 3.1 LAN 3~6 COM Ports LAN 1 & LAN 2 Quick Reference | EC543-CS...
- Page 4 Rear View EC543-CS6G86E-Q DC-in Grounding Storage Driver Bay HDMI/DP++ Combo Port 1 Mic-In/ Line-Out (Auto Detection) HDMI/DP++ Combo Port 2 Expansion Slots USB 2.0 (Auto Detection) USB 3.1 COM Ports LAN 1 & LAN 2 Quick Reference | EC543-CS...
- Page 5 Rear View EC543-CS6881-Q DC-in Grounding USB 2.0 HDMI/DP++ Combo Port 1 Expansion Slots (Auto Detection) HDMI/DP++ Combo Port 2 COM Ports (Auto Detection) USB 3.1 Storage Driver Bay LAN 1 & LAN 2 Mic-In/ Line-Out Quick Reference | EC543-CS...
- Page 6 Rear View EC543-CS98A1-Q DC-in Grounding Storage Driver Bay HDMI/DP++ Combo Port 1 Mic-In/ Line-Out (Auto Detection) HDMI/DP++ Combo Port 2 Expansion Slots COM Ports (Auto Detection) USB 3.1 Gen2 USB 3.1 Gen1 LAN 1 & LAN 2 Quick Reference | EC543-CS...
-
Page 7: Removing The Chassis Cover
There are 6 screws on both front and rear sides of the system and 6 screws on the left and right sides of the system used to secure the cover to the chassis. Remove the screws and put them in a safe place for later use. Front View Rear View Quick Reference | EC543-CS... - Page 8 Left View Right View Quick Reference | EC543-CS...
- Page 9 Step 2: Turn the system upside down and lift the cover to open the system. Step 3: The boards can be easily accessed after the chassis cover is removed. Quick Reference | EC543-CS...
-
Page 10: Installing An M.2 Card
1. Make sure the system and all other peripheral devices connected to it have been powered off. 2. Disconnect all power cords and cables. Step 1: Lift the cover to open the system. M.2 card slot can be easily accessed after the chassis cover is removed. Quick Reference | EC543-CS... - Page 11 Screw tight the card onto the stand-off with a screw driver and a stand-off screw until the gap between the card and the stand-off closes up. The card should be lying parallel to the board when it’s correctly mounted. Quick Reference | EC543-CS...
- Page 12 Before inserting a HDD/SDD, please turn off the system first. Use the following procedure to install a SATA HDD or SSD to the system: Step 1: Locate the drive bay on the front. Step 2: Pull the silver latch to unlock the door. Quick Reference | EC543-CS...
- Page 13 Slide the drive into the slot until the drive is fully seated. Close the drive latch to lock the drive in place. Important: Excessive force may damage its mechanical parts. If the HDD/SSD is inserted backward into the slot, forcing the device may damage the slot. Quick Reference | EC543-CS...
- Page 14 To install an expansion card, you need to first remove the chassis cover and turn the thumb screw counterclockwise to disassemble the slot plates and bracket. Thumb screw Slot plates Note: Supports up to 200mm in length of standard expansion cards. Quick Reference | EC543-CS...
- Page 15 Insert the expansion card into a PCI or PCIe slot on the riser card and secure the bracket in place. PCI card DFI reserves the right to change the specifications at any time prior to the product's release. This QR may be based on the product’s revision. For more documentation and drivers, please visit the download page at www.dfi.com/...