Table of Contents
Advertisement
Quick Links
Quick Installation Guide
EC900-8MM / EC910-8MM
• 1 System unit
• 1 10-Pole Terminal Block for RS-422/4-bit DIO
• 1 2-Pole Terminal Block for RS-485
• 2-Pole Terminal Block for Power Input
• DIN Rail Bracket/Screw Pack
• Quick Installation Guide
© January 04, 2023 DFI Inc.
Package Contents
Model for EC900-8MM
www.dfi.com
1
Advertisement
Table of Contents
Related Manuals for DFI EC900-8MM
Summary of Contents for DFI EC900-8MM
- Page 1 • 1 System unit • 1 10-Pole Terminal Block for RS-422/4-bit DIO • 1 2-Pole Terminal Block for RS-485 • 2-Pole Terminal Block for Power Input • DIN Rail Bracket/Screw Pack • Quick Installation Guide © January 04, 2023 DFI Inc.
-
Page 2: Product Overview
Product Overview EC900-8MM Front View Left View LAN 1 & LAN 2 HDMI USB 2.0 Status LED COM (RS485) Reset Button A terminal block: DC IN RS422 (4-pin) Digital IO (4-pin) Power (1-pin) Ground (1-pin) Quick Reference | EC900-8MM / EC910-8MM... - Page 3 Rear View Right View Antenna Hole DIN-rail Mount Quick Reference | EC900-8MM / EC910-8MM...
- Page 4 EC910-8MM Front View Left View LAN 1 & LAN 2 USB 2.0 Reset Button COM (RS485) HDMI A terminal block: Status LED DC IN RS422 (4-pin) Digital IO (4-pin) Power (1-pin) Ground (1-pin) Quick Reference | EC900-8MM / EC910-8MM...
- Page 5 Rear View Right View DIN-rail Mount Antenna Hole Quick Reference | EC900-8MM / EC910-8MM...
-
Page 6: Removing The Chassis Cover
The 2 screws on the both sides of the system are used to secure the cover to the chassis. Remove the screws and put them in a safe place for later use. Step 2: Slide the cover to open the system. Quick Reference | EC900-8MM / EC910-8MM... -
Page 7: Installing An M.2 Card
Screw tight the card onto the stand-off with a screw driver and a stand-off screw until the gap between the card and the stand-off closes up. The card should be lying parallel to the board when it’s correctly mounted. Quick Reference | EC900-8MM / EC910-8MM... -
Page 8: Installing An Antenna
Connect the internal cable to the board's antenna connector, screw the antenna connector through the antenna hole with washers and nuts, and screw on the antenna as illustrated below. Antenna Chassis Wall Module Connector Cable Antenna Connector Washer Quick Reference | EC900-8MM / EC910-8MM... -
Page 9: Mounting Options
• Din-rail mount bracket • 2 screws Step 1: Use the provided mounting screws to attach the din-rail mount bracket to the top side of the system. Step 2: Install the sytem onto the rail. Quick Reference | EC900-8MM / EC910-8MM... -
Page 10: Jumper Settings
Jumper Settings X IOJP1 „ 2-4 On: VCCP 5V (Default) „ 1-3 On: DIO 3V3 (Default) „ 3-5 On: DIO 5V (Default) „ 2-4 On: VCCP 3V3 (Default) Quick Reference | EC900-8MM / EC910-8MM... -
Page 11: Pin Assignment
PIN Assignment X RS485 Assignment DATA-_RS485 DATA+_RS485 X Digital I/O Connector Assignment D_IOA0 D_IOA1 D_IOA2 D_IOA3 RFU_PWR (3V3) Quick Reference | EC900-8MM / EC910-8MM... - Page 12 X DCN1/DC Jack Assignment X COM ( For EC910-8MM) Assignment Quick Reference | EC900-8MM / EC910-8MM...
- Page 13 X FPJP1 Assignment PSON FP_LED_3.3V SYS_LED# SYS_RST SYS_ON/RSV_BTN X TSJ1/DIO Assignment DIO0 DUO1 DIO2 DIO3 Quick Reference | EC900-8MM / EC910-8MM...
- Page 14 X TSJ2 & TSJ3 -RS232 Assignment X CBCN1/CAN Assignment 3.3V CANH CANL Quick Reference | EC900-8MM / EC910-8MM...
- Page 15 X AUJP1 Assignment LINE_OUTR LINE_OUTL DFI reserves the right to change the specifications at any time prior to the product's release. This QR may be based on the product’s revision. For more documentation and drivers, please visit the download page at www.dfi.com/...