Advertisement
Pheno
The Sustain or Vibrato effect is turned on at the panel,
but the effect is not produced at ail.
|
Cause and Solution
The effect has been improperly set. Change the setting of the effect by either turning to the correspond-
ing page in the MULTI-MENU on HE-8 or using the SUSTAIN/VIBRATO DEPTH buttons on HE-6.
The Touch feature does not work.
The TOUCH button at the right side of the panel is off. Turn on the TOUCH button.
A rhythm pattern other than the displayed panel pattern
is sounded.
A rhythm USER button is on. If you do not plan to use the User patterns, turn off the USER 1 and
USER 2 buttons.
When attempting to sound the USER 1 or 2 pattern, a
different pattern is sounded. (HE-8)
+
The panel patterns were replaced by other patterns when you transferred data from an HS Series
Electone by a FROM
PACK operation. If you wish to restore the preset User patterns, turn off
the POWER switch then turn it back on while pressing the leftmost button on the MULTI-MENU.
(page 26)
The ARPEGGIO CHORD volume is properly set, but the
Arpeggio Chord pattern is not sounded.
(D The rhythm was not started. Be sure to use ARPEGGIO CHORD together with the rhythm. (> page
22) ©) The TO UPPER or TO LOWER button in the PERCUSSIVE section is on. Turn both buttons off.
The rhythm pattern does not synchronize
with the
Arpeggio Chord pattern, or it does not synchronize with
the Fill In, Intro, and Ending patterns.
A rhythm USER button is on. The preset patterns are not designed to synchronize with User patterns.
(See [Using a User Pattern] on page 17.)
When keys on the lower or pedal keyboard are pressed,
the sounds of percussion instruments are also sounded.
The KEYBOARD PERCUSSION button is on. If you are not using Keyboard Percussion, turn it off.
(=> page 19)
The pitch in SINGLE FINGER mode does not change,
even when pressing the higher or lower keys of the
keyboard.
SINGLE FINGER mode will only produce the notes within a fixed one-octave interval. If notes having
the same letter-name are pressed anywhere on the lower keyboard, the chords that are sounded will
share the same pitch. (page 20)
[E
The harmony notes are not provided by MELODY ON
CHORD even through the upper and lower keyboards
are being played at the same.
The voice to be used for the harmony line has.not been set. Choose a voice from UPPER
ORCHESTRAL VOICES and set its volume. If the melody is played in the bass range of the upper
keyboard, the harmony notes may not be sounded. (™*page 23)
Certain functions cannot be memorized in REGISTRA-
TION MEMORY.
REGISTRATION
MEMORY
is designed not to memorize AUTO
RHYTHM
data of the START,
SYNCHRO START, FILL IN, and INTRO/ENDING buttons, as well as the data of functions, such as
PITCH. (page 24)
The Sustain or Vibrato effect is set, but the desired effect
is not produced.
Check your operating procedure. When setting an effect, the panel's SUSTAIN or VIBRATO button
must also be on. (For HE-8, see pages 35-36; for HE-6, see page 14)
Certain functions that were memorized in REGISTRA-
TION MEMORY were not programmed into C.S.P. (HE-8)
The rhythm's tempo or the AUTO BASS CHORD setting can be memorized to REGISTRATION
MEMORY, but not to C.S.P. (=P page 32)
When a REGISTRATION MENU button was pressed to
set a registration, the VOLUME lamps at two panel voice
sections lit up.
Because the volume settings of a panel registration that you set from the REGISTRATION MENU are
very finely balanced among the pertinent voice sections, two lamps will light up in certain cases.
Chords, Fill In patterns or Intro./Ending patterns cannot
be programmed to C.S.P. (HE-8)
To program a chord, press a Duration button while pressing the proper keys on the lower keyboard.
To program a Fill In or Intro. /Ending pattern, press the REGIST. button while pressing the pertinent
switch. After pressing INTRO and REGIST., be sure to program one chordless measure; after pressing
ENDING and REGIST., be sure to program two measures with chords. (page 32)
During C.S.P. programming, three warning beeps are
sounded. (HE-8)
L
When the memory capacity of a C.S.P. program is reached, three warning beeps are sounded to
indicate that no further programming is possible. ("Ppage 32)
During C.S.P. playback, the accompaniment sounds are
not produced. (HE-8)
CHORD CANCEL is ON. If you wish to play back the accompaniment sounds, set CHORD CANCEL
to OFF. (™page 32)
Inserting a new RAM Pack causes the ERROR lamp to
light.
If an unformatted RAM Pack is inserted in the Electone, the Error lamp will flash several times. In that
status, press the CONFIRM button to format the RAM Pack, then perform the TO PACK operation.
(page 25)
A TO PACK operation is performed, but the ERROR
lamp lights.
Check how the Pack was inserted as well as your To Pack operating procedure, then repeat the
operation. Also, if the RAM Pack's Memory Protect switch is ON, data will not be transferred even if
a TO PACK operation is performed. (page 25)
The Electone panel does not function normally or the
content of the memorized data has changed.
This happens very rarely. In case an abnormal voltage is input to the Electone due to an electrical
storm or other reason, the Electone may malfunction and/or the contents of its memorized data may
change. If this happens, turn off the POWER switch then turn it back on while pressing either the
rightmost button on the HE-8 MULTI-MENU or the leftmost JAZZ ORGAN button on the HE-6 VOICE
MENU.
41
Advertisement
