Advertisement
7 If registration changes are desired during programming, while pressing
the appropriate numbered button in the Registration Memory section,
press the REGIST./ == button.
From this point on, the new registration will be used.
чет
° £= °
REGISTRATION
MEMORY
C3C3C3
8 when you have completed the chord
==
—
sequence, end the program by holding
ESI
E N
RE
down
the
treble
clef
button
then
pressing the REGIST./ =
button.
A double bar symbol will be input at the end of
Or
ae
oe
the program to indicate the end of the Sequence
зз
data.
9 Turn off the EDIT/CLEAR button.
Try programming another sequence to the other SONG button by repeating Steps 1
through 9.
[Intro./Ending Program]
Intro.: At the beginning of the program, while
pressing the INTRO./ENDING button, press the
REGIST./ == button. Next, press the (©) button
to ensure that no chords are heard during this
one-measure introduction.
Ending: At the beginning of the second measure
from the end of the song, while pressing the
INTRO./ENDING
button,
press
the REGIST.
button, thereby programming
a two-measure
ending.
[Additional Information]
* Before turning off the EDIT/CLEAR, you may
want to check what you have programmed and
that you
feel are
make
any
corrections
necessary.
€ Even if you don't use the ending symbol, it will
automatically be added at the end of a song
when the EDIT/CLEAR button is turned off.
elf you make a mistake in registration during
programming, press the (4) button and then
enter the correct registration.
How to Play Back a Sequence
INTRO.
COUNT
CHORO
TRANSPOSITION
REPEAT.
CANCEL
v
a
1 Turn on one of the SONG buttons.
You can also turn on both the SONG 1 and SONG 2 buttons
to produce continuous playback.
2 Turn to the C.S.P. Play Mode page in the MULTI-
MENU. If you wish, you can now select either the
REPEAT or INTRO. COUNT functions.
REPEAT provides a continuous playback of the sequence
until it is stopped. INTRO. COUNT provides one measure of
"metronome" (count-off) before the actual playback of the
Sequence starts.
3 Start playback by turning on the auto rhythm.
Adjust the rhythm tempo and press the START switch.
Playback will commence.
4 You may now play the melody while the lower key-
board and pedal keyboard accompaniment are
being played back automatically as programmed.
You may now play a melody on the upper keyboard along
with this accompaniment. The registrations will also change
automatically as programmed.
When playback has been completed, the auto rhythm will
stop (unless REPEAT is on).
PITCH CONTROL
v
A
=
INTRO.
ENDING.
|
£=
-.
SYNCHRO
START
STAR
||
[Chord Cancel]
This button cancels the playback of the chord
and bass accompaniment. In this way you can
play the song manually, and use any registration
changes programmed in the sequence. You might
say that you have a "Registration Sequence
Programmer" too!
[Protecting C.S.P. Data]
The memorized
data will be retained in the
C.S.P. memory for at least one week even if the
power is turned off.
If you wish to store these sequences for a longer
period of time, you can use a RAM pack for this
purpose. (page 25)
[Additional Information]
@The C.S.P. Play Song buttons will operate at
any time regardless of the position of the
MULTI-MENU.
*You can also manually change registrations
during C.S.P. playback from the control panel
without affecting the contents of C.S.P. memory.
elf you transfer C.S.P. data from HS-Electone by
a FROM PACK operation, the $ , éi, and DS
data can also be played back but they cannot
be edited.
Advertisement
