Creality HALOT-ONE PLUS - 3D Printer Manual

Dear Consumers

For the best experience, please read the instructions before operating the Printer. Our teams are always ready to render you the best services. Please contact us via the phone number or e-mail address provided at the end when you encounter any problem with the Printer.

For a better experience in using our product, you can also access how to use the printer in the following ways:

View the accompanied instructions and videos in the U disk.

Visit our official website www.creality.com to find relevant software/hardware information, contact details and operation and maintenance instructions.

Firmware/Software Downloads and Upgrades

The product has access to both LycheeSlicer and CHITUBOX. WIFI printing and access to the Creative Cloud are under development.

Slicing software supported:

Download the firmware and HALOT BOX slicing software at: https://www.creality.com

Download the CHITUBOX slicing software at: https://www.chitubox.com

Download the LycheeSlicer slicing software at: https://lychee.mango3d.io

NOTES

1. Do not use the printer any way other than described to avoid personal injury or property damage.
2. Do not place the printer near any heat source or flammable or explosive objects. We suggest placing it in a well-ventilated, low-dust environment.
3. Do not expose the printer to violent vibration or any unstable environment, as this may cause poor print quality.
4. Please use recommended resin in case damage to machine.
5. Do not use any other power cable except the one supplied. Always use a grounded three-prong power outlet.
6. Please do not open the plastic cover during usage, otherwise the printing will be interrupted.
7. Do not wear cotton gloves when operating the printer. Such cloths may become tangled in the printers moving parts leading to burns, possible bodily injury, or printer damage.
8. Please wait after the print is finished. please wear gloves to take out the print tools.
9. Clean the printer frequently. Always turn the power off when cleaning, and wipe with a dry cloth to remove dust, adhered printing plastics or any other material off the frame, guide rails, or wheels. Use glass cleaner or isopropyl alcohol to clean the print surface.
10. Children under 10 years should not use the printer without supervision.
11. Tips: Do not plug or unplug the power cord when power on.
12. Users should comply with the laws and regulations of the corresponding countries and regions where the equipment is located (used), abide by professional ethics, pay attention to safety 12 obligations, and strictly prohibit the use of our products or equipment for any illegal purposes. Creality will not be responsible for any violators' legal liability under any.

Equipment Introduction

1. Hexalobular socket screw
2. Leveling screw
3. Platform plate
4. Resin vat fixing screw
5. Resin vat
6. Touch screen
7. Limit sensor
8. Air filter
9. USB port
10. Power switch
11. Power receptacle

Equipment parameters

Parts Content List

Tips: the above accessories are for reference only lease refer to the physical accessories!

Assemble the 3D Printer

Take out the resin vat, align the two tray fixing screws with the corresponding holes and tighten them to fix. (as the picture shows)

Note: put the upper cover on the machine body and the installation is completed.

Interface Information

Note: Check whether the light source is normal. The UI interfaces only for reference, the actual UI is on our website.

Leveling Platform

1. Raise the platform, loosen rubber screws on the left and right sides of the resin vat, and take out the resin vat.
   
2. Loose the four screws on the connecting plate on molding platform plate, attach calibration card on the printing screen, press Settings → Print Settings → Z axis movement → Leveling. Check whether the platform fits evenly with the paper.
   
3. After confirming that the calibration card fit evenly, lock the four screws of the platform.
   

Note: The platform has been leveled at the factory. If it needs leveling due to transportation or other reasons, please follow the steps below to adjust the printing platform.

Note: The UI is only for reference only and shall be subject to the actual UI.

Load Resin

Pour the UV photosensitive resin into the resin vat. The slot capacity is 250ml/450ml/650ml.

Tips: How to change resin?
Take out the resin vat slowly, pour out the remaining resin into the container, clean the resin vat, pour in new resin, and then install the resin vat to the machine.

Resin may cause skin irritation or an allergic skin reaction. Please wear gloves before use to avoid direct contact with the skin.

Release Film (FEP) Replacement

1. First, remove the 14 screws at the bottom of the tray and take out the broken release film (FEP).
   
2. Then place the release film between the two steel frames.
   
3. Finally, put the assembled steel frame back into the tray and tighten 14 screws.
   
4. The installed release film is as show.
   

USB Disk Printing

Slicer

1. Open the slicer software of HALOT BOX, click "Open" on the top left of the screen and add model file;
   
2. If the model needs to add support, click the upper left icon ① to set corresponding parameters ②.
   
3. Click icon ① → Setting slice printing parameters ② → Click.
   
4. Wait for slice to be finished → Select "Local Printing" to save the sliced file.
   

Note: The published UI of slicing software shall prevail for the interfaces of HALOT BOX, LycheeSlicer and CHITUBOX.

Print

1. Generate cxdlp file and save the file to U disk
   
2. Insert the USB disk
   

Note: The UI interface is for reference only, and shall be subject to the actual UI.

During the printing process the machine can't be shaken, so as not to avoid influencing affect the printing quality.

1. Select USB disk files;
   
2. Choose to use parameters;
   
3. Press "Start" button
   
4. Printing...
   

Note: The UI interface is for reference only, and shall be subject to the actual UI. The machine stores the file being printed by default.

Creality Cloud Online

Make sure WiFi is correctly connected before using online printing

Steps: Settings → WiFi → Select the corresponding WiFi.

Warm Tips:

1. Only 2.4GHz WiFi is applicable to the 3D printer, and it cannot be connect to 5GHz WiFi routers;
2. Only WPA-PSK/WPA2-PSK security protocol is applicable to the 3D printer, and other protocols may result in the failure to connect the printer to WiFi properly. To change the security protocol, users may change it in setting interface of the router.

1. Click Creality Cloud online model;
   
2. Select the model;
   
3. Download the model;
   
4. Choose to use parameters;
   
5. Click "Start" to print.
   

Note: The UI interface is for reference only, and shall be subject to the actual UI.

Creality Cloud App Print

1. Download
   
2. Register
   
3. Add equipment
   
4. Scan QR Code
   Settings → Detail → Connect to Creality Cloud → QR code
   
5. Device naming
   
6. Select model, set the printer and parameters, and click "Slice".
   
7. Upon completion of slicing, click "Printer".
   
8. Select device
   
9. Print progress
   

Notes:

1. The steps for adding devices vary for different mobile phone operating systems;
2. Set the correct area in "Settings - Other Settings - Language and Area".
3. Make sure WiFi is correctly connected before using online printing.

WIFI Print

Slicer

1. Open the slicer software of HALOT BOX, click "open" on the left of the screen and add model file.
   
2. If the model needs to add support, click the upper left icon to set corresponding parameters.
   
3. Click icon ① → Setting slice printing parameters ② → Click.
   
4. Wait for slice to be finished → Select "Remote Printing" for WiFi printing.
   
5. Once the transmission is over, select the file on the machine to start printing.
   

Note: Make sure the HALOT BOX and the printer are connected to the same WiFi.

Wiring Connection

Troubleshooting

Due to the differences between different machine models, the actual objects and the images can differ. Please refer to the actual machine. The final explanation rights shall be reserved by Shenzhen Creality 3D Technology Co., Ltd.

SHENZHEN CREALITY 3D TECNOLOGY CO., LTD
18F, JinXiuHongDu Building, Meilong Blvd., Longhua Dist., Shenzhen, China 518131
Official Website: www.creality.com
Tel: +86 755-8523 4565
E-mail: info@creality.com cs@creality.com

Documents / Resources

References

• CREALITY - Official Website, Leading 3D Printer Supplier & Manufacturer
• CREALITY - Official Website, Leading 3D Printer Supplier & Manufacturer
• CHITUBOX丨All-in-one SLA/DLP/LCD Slicer丨3D printing preprocessing software
• Download the latest version of Lychee Slicer for SLA/Resin 3D Printers

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Creality HALOT-ONE PLUS - 3D Printer Manual