1. Manuals
  2. Brands
  3. IMT Manuals
  4. Construction Equipment
  5. TH20K167
  6. Manual

IMT TH20K167 Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Copyright © 2014 Iowa Mold Tooling Co., Inc.
All rights reserved
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any
form or by any means, electronic, mechanical, photocopying, recording or otherwise without the
prior written permission of Iowa Mold Tooling Co., Inc.
Iowa Mold Tooling Co., Inc. is an Oshkosh Corporation Company.
TH20K167 Manual
Tel: 641-923-3711
Manual # 99905542
Revised 20141008
IOWA MOLD TOOLING CO., INC.
PO Box 189
Garner, IA 50438
FAX: 641-923-2424
Website: http://www.imt.com
Courtesy of Crane.Market

Advertisement

Table of Contents
loading

Related Manuals for IMT TH20K167

Summary of Contents for IMT TH20K167

  • Page 1 Manual # 99905542 TH20K167 Manual Revised 20141008 IOWA MOLD TOOLING CO., INC. PO Box 189 Garner, IA 50438 Tel: 641-923-3711 FAX: 641-923-2424 Website: http://www.imt.com Copyright © 2014 Iowa Mold Tooling Co., Inc. All rights reserved No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise without the prior written permission of Iowa Mold Tooling Co., Inc.
  • Page 2 Courtesy of Crane.Market...

  • Page 3: Table Of Contents

    Valvebank Installation ..........................19 Operation Operator Training ............................21 Tirehand Intended Use and Identification ....................22 TH20K167 Component Identification ......................22 Tirehand Equipment Inspection ........................23 Work Station Positioning ..........................23 Tirehand Controls ............................24 Tirehand Fallback Arms ..........................25 Tirehand Task Performance ........................
  • Page 4 Contents Replacement Parts ............................42 Tirehand Hydraulic Motors ........................43 Tirehand Relief Valve Adjustment ......................43 Tirehand Bearings ............................44 Turntable Bearing Thread Tightening Sequence ..................46 Turntable Bearing Inspection ........................47 Thread Torque Chart (English) ........................48 Thread Torque Chart (Metric) ........................49 Tirehand Parts Tirehand Parts Ordering Information ......................

  • Page 5: Revisions

    Revisions DATE LOCATION DESCRIPTION 20130603 Pages 51-64 Added parts information. 20130711 Chapter 8 Added camera option information per engineering. 20131003 73734735 Added per engineering mark-up 20131010 Chapter 8/9 Added Radio Remote Chapter 8. Chapter 9 was 8. 20141008 Chapter 7 Added cylinders.
  • Page 6 Courtesy of Crane.Market...

  • Page 7: Tirehand Introduction

    Modifications to your equipment must be performed with IMT approved accessories, parts and optional equipment. If in doubt, contact IMT prior to making any modifications. DO NOT alter or modify any safety device! All safety devices must be inspected, tested and maintained in proper working condition.
  • Page 8 TH20K167 Manual #99905542 RESPONSIBILITY It is the user’s responsibility to maintain and operate this unit in a manner that will result in the safest working conditions possible. In addition, it is the user’s responsibility to be aware of existing Federal, State, and Local codes and regulations governing the safe use and maintenance of this equipment.

  • Page 9: Th20K167 Specifications

    H A P T E R TH20K167 Specifications In This Chapter General Specifications .............. 8 Dimensional Drawing, Forklift Mounting ........9 Dimensional Drawing, Loader Mounting ........10 Capacity Chart ................11 Courtesy of Crane.Market...

  • Page 10: General Specifications

    VEHICLE COMPATIBILITY The Tirehand TH20K167 will permanently adapt to either a forklift truck or a front-end loader. When mounting to a forklift truck, it is recommended that the truck be equipped with a sideshifter. If adapted to a front-end loader, quick couplers are available which enable the disconnection of the Tirehand so that the original bucket can be quickly coupled to the machine for normal operations.

  • Page 11: Dimensional Drawing, Forklift Mounting

    Chapter 2 TH20K167 Specifications Dimensional Drawing, Forklift Mounting Dimensions in inches (mm). 15" (381) 50" 167" 100" (2540) (1270) (4242) 83" (2110) ø35.5" (902) 87.5" CG (2222) with 10,500 lb (4763 kg) tirehand and 20,000 lb (9072 kg) tire & rim. 158" (4013) between pads 111.5"...

  • Page 12: Dimensional Drawing, Loader Mounting

    TH20K167 Manual #99905542 Dimensional Drawing, Loader Mounting Dimensions in inches (mm). 15" (381) 50" 167" 100" (2540) (1270) (4242) 83" (2110) ø35.5" (902) 90.5" (2300 cm) CG with 11,650 lb (5284 kg) tirehand and 20,000 lb (9072) tire & rim.

  • Page 13: Capacity Chart

    Chapter 2 TH20K167 Specifications 11 Capacity Chart CAPACITY CHART MAXIMUM CAPACITY 20,000 LB (9072 KG) CLAMPING SPAN MIN: 50" (127 cm) MAX: 167" (424 cm) 70399418 Courtesy of Crane.Market...
  • Page 14 Courtesy of Crane.Market...

  • Page 15: Installation

    H A P T E R Installation In This Chapter Tirehand Installation Introduction ..........14 Typical Tirehand Hydraulic Installation ........15 Loader Installation ..............16 Lift Truck Installation ..............17 Bulkhead Installation ..............18 Valvebank Installation ............... 19 Courtesy of Crane.Market...

  • Page 16: Tirehand Installation Introduction

    (172.4 - 206.8 bar). A flow divider may be required if the forklift or loader pump provides excess flow. Contact IMT for specific installation instructions on any type of installation. Prior to connecting any electrical connections between the tirehand and the loader or forklift, check the tirehand voltage.

  • Page 17: Typical Tirehand Hydraulic Installation

    PSI (172.4 - 206.8 bar). Some of the components shown on the typical hydraulic installation drawing, including the flow dividers, reservoir, filter, pump, and drain, are not provided by IMT but are part of the loader or forklift. Contact IMT for specific installation instructions on any type of installation.

  • Page 18: Loader Installation

    TH20K167 Manual #99905542 Loader Installation NOTE: Tirehand installations vary based on the carrier vehicle. Contact IMT for specific installation assistance. Mount the Tirehand to loader arms using the original loader pins. Splice the flow control divider into the existing pressure line. Continue the original line to its original destination (bucket, etc.), and route the controlled line (with 12 gpm (45.4 lpm) at...

  • Page 19: Lift Truck Installation

    Chapter 3 Installation 17 Lift Truck Installation Mount the Tirehand to lift truck using the original carriage pin. Splice the flow control divider into the existing pressure line. Continue the original line to its original destination (forklift function, etc.), and route the controlled line (with 12 gpm (45.4 lpm) at 2500-3000 psi (172.4 - 206.8 bar)) to the tirehand valvebank.

  • Page 20: Bulkhead Installation

    TH20K167 Manual #99905542 Bulkhead Installation If the forklift on which the tirehand is installed includes control valves, all of the hydraulic lines from the forklift control valves must culminate at the front of the carriage. The forklift will connect to the tirehand using a bulkhead plate. The forklift manufacturer must furnish oil for all hydraulic functions.

  • Page 21: Valvebank Installation

    Chapter 3 Installation 19 Valvebank Installation When the Tirehand has a valvebank, connect the valvebank to the forklift or loader hydraulic system using the hydraulic pressure and return line from the forklift or loader Install the Tirehand on the loader or forklift, connecting the suction and return lines from the forklift or loader to the tirehand valvebank.
  • Page 22 Courtesy of Crane.Market...

  • Page 23: Operation

    H A P T E R Operation In This Chapter Operator Training ..............21 Tirehand Intended Use and Identification ......... 22 Component Identification ............22 Tirehand Equipment Inspection ..........23 Work Station Positioning ............23 Tirehand Controls ..............24 Tirehand Fallback Arms ............25 Tirehand Task Performance .............

  • Page 24: Tirehand Intended Use And Identification

    TH20K167 Manual #99905542 Tirehand Intended Use and Identification This Tirehand is a tire lifting and positioning device. It should be used to remove, transport, replace, and storage stack tires. It is designed only as a tire handling device and should not be used for any other purposes.

  • Page 25: Tirehand Equipment Inspection

    Chapter 4 Operation 23 Tirehand Equipment Inspection Daily and weekly, before use, the operator should inspect as listed: ITEM DESCRIPTION FREQUENCY DAILY WEEKLY WALK-AROUND Inspect for hydraulic leaks, loose parts and obvious structural INSPECTION member damage. ROTATION SYSTEM Check for excessive backlash (play) between pinion gear and turntable gear-bearing.

  • Page 26: Tirehand Controls

    TH20K167 Manual #99905542 Tirehand Controls LEFT BODY ROTATE SIDE SHIFT CLAMP RIGHT PAD ROTATE CLAMP RELEASE Hold toggle with Power CLAMP release switch switch to open Fallback clamp. Arm switch Emergency Stop switch NOTE: See the TireHandler Radio Remote System manual #99905678 for complete radio remote control system instructions.

  • Page 27: Tirehand Fallback Arms

    Chapter 4 Operation 25 Tirehand Fallback Arms The Tirehand is equipped with fallback arms to prevent tire movement toward the working area between the tire and the back of the tirehand. When deployed, the fallback arms are positioned perpendicular to the arm assembly to prevent the tire from falling into the work area. They need to be positioned in-line with the arm assembly when rotating the tire.

  • Page 28: Tirehand Task Performance

    TH20K167 Manual #99905542 Tirehand Task Performance To begin operation: 1 Open the tirehand clamps. 2 Maneuver the vehicle into a position so that the tirehand can be used to clamp the center of the tire with the tirehand body parallel to the ground. Raise the loader or forklift so the tirehand is elevated correctly.
  • Page 29 Chapter 4 Operation 27 WARNING If the tire is in a vertical position, the tire blocks operator visibility during transport. DO NOT transport tire in t his position! Rotate the pads so that the tire is in a horizontal position, parallel to the ground, before transporting.

  • Page 30: Tirehand Operating Restrictions

    TH20K167 Manual #99905542 Clamp the tire securely. Remember, clamp pressure changes as the weight shifts between the clamps. When the tire is vertical, the fallback arms, a safety device in case of operator error, will prevent the tire from falling into the space between the clamp and the body. Make sure the fallback arms are engaged when the tire is in the vertical position.

  • Page 31: Tirehand Electrical Safety

    Chapter 4 Operation 29 The rotation system on the Tirehand is designed to allow the user to manipulate large tires. It is a precision function that was not designed to apply high loads. However, the load holding valves that are built into this system to help control the tire during handling will also prevent the body of the Tirehand from rotating freely when loads are applied to a single Tirehand arm.

  • Page 32: Tirehand Warnings

    TH20K167 Manual #99905542 Tirehand Warnings Warning decals are installed on the Tirehand, as well as on the loader or forklift, to give information about possible hazards. All decals must be installed and legible. If decals are damaged, they must be replaced. Refer to the parts section for the decal part numbers and locations on the Tirehand.
  • Page 33 Chapter 4 Operation 31 FAILURE TO OBEY THE FOLLOWING WILL RESULT IN DANGER DEATH, SERIOUS INJURY, INSTABILITY OR EQUIPMENT DAMAGE NEVER attempt to handle tires filled with NEVER drag the tire - the unit is designed ballast. Stability or structural failure may to lift and carry.
  • Page 34 Courtesy of Crane.Market...

  • Page 35: Maintenance

    For information concerning extreme condition lubrication, contact your local service representative. Note that the service schedule in this manual pertains only to the IMT tirehand. In addition to tirehand maintenance, it is your responsibility to follow all inspection and maintenance procedures for the forklift or loader, as defined in the forklift or loader maintenance manual.

  • Page 36: Tirehand Lubrication Points

    TH20K167 Manual #99905542 Tirehand Lubrication Points LUBRICATION CHART APPLICATION POINT LUBRICATION APPLICATION INTERVAL Side Shift Pins (if Shell Alvania 2EP applicable) Hand Grease Gun Body - Arm Link Pins (Top Weekly & Bottom, both sides) Shell Retinax "A" Arm / Hand Link Pins (Top Pneumatic Pressure Gun &...

  • Page 37: Tirehand Preventative Maintenance

    Chapter 5 Maintenance 35 Tirehand Preventative Maintenance The Tirehand Inspection Checklist is designed to assist in keeping the Tirehand in peak operating condition. The information in this section refers to the Tirehand only. Items which apply to your Tirehand should be checked before it is put into operation. Inspect to the frequency indicated in the chart.
  • Page 38 TH20K167 Manual #99905542 HYDRAULIC CONTROL VALVES 1 Check spools for sticking and failure to return to neutral position. Inspect for leaks at joints and spools. 2 Inspect valve housing for cracks. 3 Make certain relief valve reaches the proper relief setting.

  • Page 39: Tirehand Inspection Chart

    Chapter 5 Maintenance 37 Tirehand Inspection Chart ITEM (* indicates a DESCRIPTION FREQUENCY critical item) DAILY WEEKLY MONTHLY WALK-AROUND Inspect for hydraulic leaks, loose parts and obvious INSPECTION structural member damage. *MOUNTING BOLTS Check torque (power-wrench tight). ROTATION SYSTEM Check for excessive backlash (play) between pinion gear and turntable gear-bearing.
  • Page 40 Courtesy of Crane.Market...

  • Page 41: Tirehand Repair

    H A P T E R Tirehand Repair In This Chapter Tirehand Troubleshooting ........... 40 Tirehand Cylinders ............. 41 Replacement Parts ............. 42 Tirehand Hydraulic Motors ..........43 Tirehand Relief Valve Adjustment........43 Tirehand Bearings .............. 44 Turntable Bearing Thread Tightening Sequence ....46 Turntable Bearing Inspection ..........

  • Page 42: Tirehand Troubleshooting

    TH20K167 Manual #99905542 Tirehand Troubleshooting SYMPTOM PROBABLE CAUSE Controls fail to respond.  E-stop on remote pressed in.  Remote not turned on.  Pump not engaged - if supplied with electric clutch.  Hydraulic oil supply is low. ...

  • Page 43: Tirehand Cylinders

    Chapter 6 Tirehand Repair 41 Tirehand Cylinders The Tirehand uses similar cylinders in all functions. Common disassembly and repair instructions apply. Check the Parts section for specific information. CLAMP CYLINDER REMOVAL & INSTALLATION To remove the clamp cylinder: 1 Rotate the Tirehand until the clamp cylinder is in a horizontal position. 2 Extend the cylinder full stroke.

  • Page 44: Replacement Parts

    TH20K167 Manual #99905542 5 Check the hydraulic fluid level with all cylinders retracted. Fill if necessary. 6 Test the unit with a simulated job operation before proceeding to the job site. SIDE SHIFT CYLINDER REMOVAL AND INSTALLATION To remove the side shift cylinder: 1 Rotate the Tirehand so that the side shift cylinder is in a horizontal position.

  • Page 45: Tirehand Hydraulic Motors

    Chapter 6 Tirehand Repair Tirehand Hydraulic Motors Four hydraulic motors are used on the Tirehand: two for Tirehand rotation and one each side for pad rotation. These motors are not considered field repairable and should be replaced if defective. HYDRAULIC MOTOR REMOVAL AND REPLACEMENT To remove rotation motor: 1 Disconnect and cap the hydraulic hoses.

  • Page 46: Tirehand Bearings

    TH20K167 Manual #99905542 Tirehand Bearings This section includes instructions on the removal and installation of turntable gear-bearings and bushings. TURNTABLE GEAR-BEARING To remove the Tirehand rotation gear-bearing: 1 Disconnect and cap the hydraulic hoses from the valvebank. 2 Support the clamp arms with an overhead lifting device capable of supporting the weight of the unit.
  • Page 47 Chapter 6 Tirehand Repair 3 Remove the gear-bearing mounting bolts and remove the bearing. 4 Position the bearing so that the holes align with those in the arm. The grease fitting extension port must be toward the pinion gear. Install and torque the mounting bolts (see Torque Table).

  • Page 48: Turntable Bearing Thread Tightening Sequence

    TH20K167 Manual #99905542 BUSHING INSTALLATION ILLUSTRATION Turntable Bearing Thread Tightening Sequence Refer to the turntable bearing thread tightening diagram below for proper tightening/torqueing sequence of the turntable bearing to the crane base and crane mast. The total quantity of cap screws varies dependent on crane model.

  • Page 49: Turntable Bearing Inspection

    3 Noise emitting from the bearing during rotation. 4 Rough rotation. 5 Uneven or excessive wear between the pinion gear and turntable gear. If one or more of the above conditions exists, further inspection may be required. Contact IMT for assistance. Courtesy of Crane.Market...

  • Page 50: Thread Torque Chart (English)

    TH20K167 Manual #99905542 Thread Torque Chart (English) FINE THREAD BOLTS (ENGLISH) COARSE THREAD BOLTS (ENGLISH) SIZE BOLT GRADE 5 GRADE 8 SIZE BOLT GRADE 5 GRADE 8 DIA. DIA. SAE J429 SAE J429 SAE J429 SAE J429 GRADE 5 GRADE 5...

  • Page 51: Thread Torque Chart (Metric)

    Chapter 6 Tirehand Repair Thread Torque Chart (Metric) FINE THREAD TORQUE CHART (METRIC) COARSE THREAD TORQUE CHART (METRIC) TIGHTENING TORQUE TIGHTENING TORQUE SIZE BOLT SIZE BOLT (DIA- DIA. (DIA- DIA. TPI) (INCHES) TPI) (INCHES) SAE J429 SAE J429 SAE J429 SAE J429 GRADE 5 GRADE 5...
  • Page 52 Courtesy of Crane.Market...

  • Page 53: Tirehand Parts

    H A P T E R Tirehand Parts In This Chapter Parts Ordering Information ............Hand Assembly (40724866) ..............Sub Base Assembly (40724867) ..........Body Assembly (40724868) ........................Clamp Assembly (40724869) Sub Base Assembly - Short (40724903) ................ Sub Base Assembly w/o Side Shift (40724910) ................

  • Page 54: Tirehand Parts Ordering Information

    TH20K167 Manual #99905542 Tirehand Parts Ordering Information GENERAL This section contains the exploded parts drawings, with accompanying parts lists, for the assemblies used on the Tirehand. These drawings are intended to be used for ordering parts only. CYLINDER IDENTIFICATION To ensure proper replacement parts are received, it is necessary to specify the complete number/letter sequence for any part request.

  • Page 55: Hand Assembly (40724866)

    Chapter 7 Tirehand Parts Hand Assembly (40724866) HARDWARE IS CONTAINED IN KIT 91724889 LEFT HAND DETAIL: GEAR TRAIN 19 8 NOTE: INSTALL TURNTABLE BEARING WHERE GREASE ZERK IS LOCATED AT MISSING BOLT MOUNTING LOCATION. DETAIL A RIGHT HAND NOTE: INSTALL TURNTABLE BEARING WHERE GREASE ZERK IS LOCATED AT MISSING BOLT MOUNTING LOCATION.
  • Page 56 TH20K167 Manual #99905542 40724866 PARTS LIST ITEM PART # DESCRIPTION 60139307 COVER-FALL BACK CYL 52724549 HAND WLDMT-TH20K 52724551 FLAG-WLDMT TH20K W-FALLBACK 52724552 WLDMT-PIVOT, FALLBACK ARM 52724550 CLAW-WLDMT TH20K 71056389 GEAR-TRNTBL BRG 449-05190-1 71056265 GEAR-PINTION 301-10104-1 60139308 PLATE-GREASE 71056264 GEAR-INTMD 301-10103-1...

  • Page 57: Sub Base Assembly (40724867)

    Chapter 7 Tirehand Parts Sub Base Assembly (40724867) 7 19 HARDWARE IS CONTAINED IN KIT 91724891 40724867 PARTS LIST ITEM PART # DESCRIPTION ITEM PART # DESCRIPTION 52724547 SUB-BASE WLDMT-20K 72601485 CAP SCR .75-10X 1.50 HH GR8 Z BASE WELDMENT 60030253 WEAR PAD-SIDE SHIFTER TH2557B 60117737...

  • Page 58: Body Assembly (40724868)

    TH20K167 Manual #99905542 Body Assembly (40724868) REAR VIEW HARDWARE IS CONTAINED IN KIT 91724888 FRONT VIEW 40724868 PARTS LIST ITEM PART # DESCRIPTION 52724548 BODY-WLDMT TH20K 52725478 WLDMT-TH20 BODY ROTATION BRKT 60117741 COVER PLATE-BODY 71056676 BEARING ROTATION 72060092 CAP SCR .50-13X 1.25 HH GR5 Z 72063053 WASHER .50 LOCK...

  • Page 59: Clamp Assembly (40724869)

    Chapter 7 Tirehand Parts Clamp Assembly (40724869) 40724869 PARTS LIST ITEM PART # DESCRIPTION 3B287930 CYL-4.0/2.5 19.25S 42.00CC C 52711931 ARM WLDMT TIREHAND 2557B 51724567 CYL-3.0/1.5 5.00S 13.75 CC C 71415017 KEEPER-PIN .75 60139296 PIN-TYPE H 2.50X27.75 60139298 PIN-TYPE H 1.50 X 4.00 71415014 KEEPER-PIN .38 72063051...

  • Page 60: Sub Base Assembly - Short (40724903)

    TH20K167 Manual #99905542 Sub Base Assembly - Short (40724903) 7 19 HARDWARE IS CONTAINED IN KIT 91724891 40724903 PARTS LIST ITEM PART # DESCRIPTION ITEM PART # DESCRIPTION 52724901 SUB-BASE WLDMT-20K 72601485 CAP SCR .75-10X 1.50 HH GR8 Z BASE WELDMENT...

  • Page 61: Sub Base Assembly W/O Side Shift (40724910)

    Chapter 7 Tirehand Parts Sub Base Assembly w/o Side Shift (40724910) HARDWARE IS CONTAINED IN KIT 91724891 40724910 PARTS LIST ITEM PART # DESCRIPTION 51724564 CYL-4.0/2.0 09.25S 22.5CC SUB-BASE WLDMT-20K 60139299 PIN-TYPE H 1.50X 5.25 60139300 PIN-TYPE F 1.50X 9.88 71415014 KEEPER-PIN .38 72060047...

  • Page 62: Cylinder (51724564)

    TH20K167 Manual #99905542 Cylinder (51724564) #15 HOLE DRILLED 0.188” DEE P PRESS IN PART #60125699 SECTION A-A 18 (2) 18 (2) 22” CLOSED - 32” OPEN - 9” STROKE NOTES: IT IS RECOMMENDED THAT ALL COMPONENTS OF THE SEAL KIT BE REPLACED WHENEVER THE CYLINDER IS DISSASSEMBLED.

  • Page 63: Cylinder (51724567)

    Chapter 7 Tirehand Parts Cylinder (51724567) 15” CLOSED - 19” OPEN - 5.00” STROKE 17 (2) #15 HOLE DRILLED 0.188” DEE P PRESS IN PART #60125699 16 (2) 16 (2) DETAIL C SCALE 1/2 NOTES: IT IS RECOMMENDED THAT ALL COMPONENTS OF THE SEAL KIT BE REPLACED WHENEVER THE CYLINDER IS DISSASSEMBLED.

  • Page 64: Cylinder (3B282930)

    TH20K167 Manual #99905542 Cylinder (3B282930) #15 HOLE DRILLED 0.188” DEE P SAE #8 PRESS IN PART #60125699 O-RING PORTS 3 15 23” CLOSED - 35” OPEN - 12” STROKE NOTES: IT IS RECOMMENDED THAT ALL COMPONENTS OF THE SEAL KIT BE REPLACED WHENEVER THE CYLINDER IS DISSASSEMBLED.

  • Page 65: Cylinder (3B287930)

    PISTON – 4.02 BORE X 1.44 STRG 6C300025 STOP TUBE – 2.50 ROD X 3.00 LONG 73054242 VALVE-CBAL 25 GPM 9C160920 SEAL KIT – IMT 4.02 2.50 1.44 7T66P400 PISTON SEAL – DYNAMIC 4.00” (PSP 1REF 7T2N4040 WEAR RING – 4.00 OD X .50 WIDE...

  • Page 66: Camera Kit - Dual (40724922)

    TH20K167 Manual #99905542 Camera Kit – Dual (40724922) 40724922 PARTS LIST ITEM PART # DESCRIPTION 52724835 BODY-WLDMT TH25 60136590 CAMERA MOUNT 60139306 GUARD-CAMERA MNT 71414717 NUT- .25-20 CHANNEL 72060004 CAP SCR .25-20X 1.00 HH GR5 Z 72060046 CAP SCR .38-16X 1.00 HH GR5 Z 72063003 WASHER .38 FLAT...

  • Page 67: Hydraulic Kit W/Valve Bank (91724907)

    Chapter 7 Tirehand Parts Hydraulic Kit w/Valve Bank (91724907) 91724907 PARTS LIST ITEM PART # DESCRIPTION ITEM PART # DESCRIPTION 72532768 TEE, #4 MJIC 51396584 HOSE-FZ .50X 27.50 (8-8) 100R17 73054829 FLOW DIVIDER 51396204 HOSE-FZ .50 X 45.00(8-8) 72532358 ADAPTER #8 MALE STR #8 MALE JIC 51396964 HOSE-FJ .50 X 96.00 72531205...

  • Page 68: Valvebank (73734735)

    TH20K167 Manual #99905542 Valvebank (73734735) 73734735 PARTS LIST PART # DESCRIPTION 94392213 SEAL KIT, CONNECTION BLOCK 94399214 SEAL KIT, SEALS BETWEEN SECTIONS 73734727 24V COIL FOR SOLENOID Courtesy of Crane.Market...

  • Page 69: Valvebank Schematic (73734735)

    Chapter 7 Tirehand Parts Valvebank Schematic (73734735) Courtesy of Crane.Market...

  • Page 70: Hydraulic Kit W/O Valve Bank (91724923)

    TH20K167 Manual #99905542 Hydraulic Kit w/o Valve Bank (91724923) 91724923 PARTS LIST ITEM PART # DESCRIPTION ITEM PART # DESCRIPTION 72532768 TEE, #4 MJIC 51393976 HOSE-FF 0.25X 42.00 (4-4) 73054915 FLOW DIVIDER 51397667 HOSE-FJ .50 X 46.00 (8-8) 72532358 ADPTR #8 MALE STR/#8 MALE JIC 51396821 HOSE-FF .25 X 96.00 (4-4)

  • Page 71: Harness - Tirehand Radio Remote (77441524)

    Chapter 7 Tirehand Parts Harness – Tirehand Radio Remote (77441524) CJ-40 0 BRAD/HARRIS: 8R5A00A18A120 SPLI CE G CP-1200 DEUTSCH: DTM06-12SA 80012 1062-20-0122 WM12S CA V ITY PLUG : 0413-204-2005 C AVITY C OL O R P RI NT L ABE L C ON -SPL C C AV ITY CJ-600...
  • Page 72 TH20K167 Manual #99905542 Courtesy of Crane.Market...

  • Page 73: Harness - Tirehand Chassis Interface (77441525)

    Chapter 7 Tirehand Parts Harness – Tirehand Chassis Interface (77441525) Courtesy of Crane.Market...

  • Page 74: Harness - Tirehand Radio Remote (77441525)

    TH20K167 Manual #99905542 Harness – Tirehand Radio Remote (77441525) Courtesy of Crane.Market...

  • Page 75: Decal Kit (95724918)

    PLACARD-SERIAL NUMBER 1 70391612 DECAL-GREASE WEEKLY (LEFT) 70391613 DECAL-GREASE WEEKLY (RIGHT) 70392524 DECAL-ROTATE CRANE WHILE GREAS 70393671 DECAL-TH OPERATION WARNINGS 70393672 DECAL-DANGER TH OPERATION 70399140 DECAL-DIAMOND IMT 6.75X13.50 REFL 72661638 TACK-METAL DECAL 1 CAPACITY CHART DECAL 2 IDENTIFICATION DECAL Courtesy of Crane.Market...

  • Page 76: Recommended Spare Parts

    Parts not listed are considered as not being Critical or Normal Wear items during the first year of operation. PART # DESCRIPTION 40725220 SPARE PARTS LIST TH10K 51717952 SEAL KIT-IMT 3.00B 1.50R 1.06S 60020167 BUSHING-BRZ 2.50X 3.00X 3.75 60020181 BUSHING-B148 ROTATION 60020182 BUSHING-B148 ROTATION 60020246 BUSHING-BRZ 1.50X 2.25X 0.94...

  • Page 77: Radio Remote

    H A P T E R Radio Remote For Radio Remote operation instructions, features, specifications, and programming, see the TireHandler Radio Remote System manual P/N 99905678. Courtesy of Crane.Market...
  • Page 78 Courtesy of Crane.Market...

  • Page 79: Camera Option

    H A P T E R Camera Option In This Chapter ..........Camera Kit (40724922) ......... Monitor-Dual Vision (77734784) ..... Camera-For Dual Vision Monitor (77734785) Cable-Coax 65’ for Dual Vision Monitor (77734786) Courtesy of Crane.Market...

  • Page 80: Camera Kit - Dual (40724922)

    TH20K167 Manual #99905542 Camera Kit – Dual (40724922) 40724922 PARTS LIST ITEM PART # DESCRIPTION 52724835 BODY-WLDMT TH25 60136590 CAMERA MOUNT 60139306 GUARD-CAMERA MNT 71414717 NUT- .25-20 CHANNEL 72060004 CAP SCR .25-20X 1.00 HH GR5 Z 72060046 CAP SCR .38-16X 1.00 HH GR5 Z 72063003 WASHER .38 FLAT...

  • Page 81: Monitor-Dual Vision (77734784)

    Chapter 9 Camera Option MONITOR-DUAL VISION (77734784) Courtesy of Crane.Market...
  • Page 82 TH20K167 Manual #99905542 Monitor-Dual Vision (77734784) Courtesy of Crane.Market...
  • Page 83 Chapter 9 Camera Option Monitor-Dual Vision (77734784) Courtesy of Crane.Market...
  • Page 84 TH20K167 Manual #99905542 Monitor-Dual Vision (77734784) Courtesy of Crane.Market...
  • Page 85 Chapter 9 Camera Option Monitor-Dual Vision (77734784) Courtesy of Crane.Market...
  • Page 86 TH20K167 Manual #99905542 Monitor-Dual Vision (77734784) Courtesy of Crane.Market...
  • Page 87 Chapter 9 Camera Option Monitor-Dual Vision (77734784) Courtesy of Crane.Market...
  • Page 88 TH20K167 Manual #99905542 Monitor-Dual Vision (77734784) Courtesy of Crane.Market...
  • Page 89 Chapter 9 Camera Option Monitor-Dual Vision (77734784) Courtesy of Crane.Market...
  • Page 90 TH20K167 Manual #99905542 Monitor-Dual Vision (77734784) Courtesy of Crane.Market...
  • Page 91 Chapter 9 Camera Option Monitor-Dual Vision (77734784) Courtesy of Crane.Market...
  • Page 92 TH20K167 Manual #99905542 Monitor-Dual Vision (77734784) Courtesy of Crane.Market...
  • Page 93 Chapter 9 Camera Option Monitor-Dual Vision (77734784) Courtesy of Crane.Market...
  • Page 94 TH20K167 Manual #99905542 Monitor-Dual Vision (77734784) Courtesy of Crane.Market...
  • Page 95 Chapter 9 Camera Option Monitor-Dual Vision (77734784) Courtesy of Crane.Market...
  • Page 96 TH20K167 Manual #99905542 Monitor-Dual Vision (77734784) Courtesy of Crane.Market...
  • Page 97 Chapter 9 Camera Option Monitor-Dual Vision (77734784) Courtesy of Crane.Market...
  • Page 98 TH20K167 Manual #99905542 Monitor-Dual Vision (77734784) Courtesy of Crane.Market...
  • Page 99 Chapter 9 Camera Option Monitor-Dual Vision (77734784) Courtesy of Crane.Market...
  • Page 100 TH20K167 Manual #99905542 Monitor-Dual Vision (77734784) Courtesy of Crane.Market...
  • Page 101 Chapter 9 Camera Option Monitor-Dual Vision (77734784) Courtesy of Crane.Market...
  • Page 102 TH20K167 Manual #99905542 Monitor-Dual Vision (77734784) Courtesy of Crane.Market...
  • Page 103 Chapter 9 Camera Option Monitor-Dual Vision (77734784) Courtesy of Crane.Market...
  • Page 104 TH20K167 Manual #99905542 Monitor-Dual Vision (77734784) Courtesy of Crane.Market...

  • Page 105: Camera-For Dual Vision Monitor (77734785)

    Chapter 9 Camera Option Camera-For Dual Vision Monitor (77734785) Courtesy of Crane.Market...
  • Page 106 TH20K167 Manual #99905542 Camera-For Dual Vision Monitor (77734785) Courtesy of Crane.Market...
  • Page 107 Chapter 9 Camera Option Camera-For Dual Vision Monitor (77734785) Courtesy of Crane.Market...
  • Page 108 TH20K167 Manual #99905542 Camera-For Dual Vision Monitor (77734785) Courtesy of Crane.Market...

  • Page 109: Cable-Coax 65' For Dual Vision Monitor (77734786)

    Chapter 9 Camera Option Cable-Coax 65’ for Dual Vision Monitor (77734786) Courtesy of Crane.Market...

Table of Contents