Page 1
View thousands of Crane Specifications on FreeCraneSpecs.com View thousands of Crane Specifications on FreeCraneSpecs.com 99903278 : IM-9/63: PAGE 1: 20061113 Model 9/63 Instruction Manual NOTE Read and understand this manual, the IMT Operators Crane Safety Manual and Safety Manual Supplement before operating or maintaining your crane.
20. Extension cylinder 2.0 General Safety Considerations WARNING Prior to operation, read and understand the IMT Operator’s Crane Safety manual and any other safety manuals which accompanied the loader. General Considerations for Loader Safety and Stability Prior to starting the loader, the operator must check the following factors: 1.
View thousands of Crane Specifications on FreeCraneSpecs.com View thousands of Crane Specifications on FreeCraneSpecs.com 99903278 : IM-9/63: PAGE 4: 20010507 DANGER ELECTROCUTION HAZARD THIS CRANE IS NOT INSULATED DEATH OR SERIOUS INJURY WILL RESULT FROM CONTACT OR INADEQUATE CLEARANCE Maintain safe clearance from electrical lines.
View thousands of Crane Specifications on FreeCraneSpecs.com View thousands of Crane Specifications on FreeCraneSpecs.com 99903278 : IM-9/63: PAGE 6: 20010507 Loader Valve Bank Activation NOTES FOR SAFE OPERATION:...
The loader is marked with factory-installed lifting capacity decals. These decals must be intact and legible. If the decal has been damaged or removed, order a new decal from IMT using the part number from the decal or consult the parts manual, decal kit.
Page 9
View thousands of Crane Specifications on FreeCraneSpecs.com View thousands of Crane Specifications on FreeCraneSpecs.com 99903278 : IM-9/63: PAGE 9: 20010507 IOWA MOLD TOOLING CO., INC. BOX 189 GARNER 50438 641-923-3711 l Working loads will be limited to those shown. Model Deduct the weight of load handling devices.
Page 10
View thousands of Crane Specifications on FreeCraneSpecs.com View thousands of Crane Specifications on FreeCraneSpecs.com 20010507 99903278 : IM-9/63: PAGE 10: IOWA MOLD TOOLING CO., INC. BOX 189 GARNER 50438 641-923-3711 l Working loads will be limited to those shown. Model Deduct the weight of load handling devices.
Page 11
View thousands of Crane Specifications on FreeCraneSpecs.com View thousands of Crane Specifications on FreeCraneSpecs.com 99903278 : IM-9/63: PAGE 11: 20010507 IOWA MOLD TOOLING CO., INC. BOX 189 GARNER 50438 641-923-3711 l Working loads will be limited to those shown. Model Deduct the weight of load handling devices.
Page 12
View thousands of Crane Specifications on FreeCraneSpecs.com View thousands of Crane Specifications on FreeCraneSpecs.com 99903278 : IM-9/63: PAGE 12: 20010507 IOWA MOLD TOOLING CO., INC. BOX 189 GARNER 50438 641-923-3711 l Working loads will be limited to those shown. Model Deduct the weight of load handling devices.
View thousands of Crane Specifications on FreeCraneSpecs.com View thousands of Crane Specifications on FreeCraneSpecs.com 99903278 : IM-9/63: PAGE 14: 20010507 7.0 Working Pressure / Performance WORKING PRESSURE-9-63 FIGURE 10: WORKING PRESSURE VALVE TEST/ADJUSTMENT POSITION Basic position during test and adjustment of valves Working pressure on main-relief valve &...
CAUTION The main relief valve, the load holding valves, the dump valve and the external relief valve are sealed. Check these seals regularly and have an authorized IMT service center replace them if damaged. 8.2 Recommended Hydraulic Oil Types Oil Brand...
Page 16
View thousands of Crane Specifications on FreeCraneSpecs.com View thousands of Crane Specifications on FreeCraneSpecs.com 99903278 : IM-9/63: PAGE 16: 20010507 STANDARD HYDRAULIC DIAGRAM...
If defects, damage or leaks are found, repair them immediately. Always have your repairs performed by an authorized IMT service center. Repairs to the hydraulic system must be made only at an authorized service center. When ordering parts for your loader, please state: •...
99903278 : IM-9/63: PAGE 18: 20010507 11.2 Annual Service Overhaul Each year the loader should be given a complete service overhaul at an authorized IMT service center. The service check must include: 1. Oil change for hydraulic oil in tank and rotation system.
Page 19
View thousands of Crane Specifications on FreeCraneSpecs.com View thousands of Crane Specifications on FreeCraneSpecs.com 99903278 : IM-9/63: PAGE 19: 20010507 IOWA MOLD TOOLING CO., INC. BOX 189, GARNER, IA 50438-0189 TEL: 641-923-3711 TECHNICAL SUPPORT FAX: 641-923-2424...