Growatt ShineWiFi-X Manual page 2

Growatt ShineWiFi-X
Quick Installation Guideline
For more info, please download from http://server.growatt.com
+86 755 2747 1942 F +86 755 2747 2131
E service@ginverter.com W www. growatt.com
Turn on inverter and check ShineWiFi-X state
Step2.
After install the ShineWiFi-X module, turn on the inverter, red LED
flashing indicates the inverter and ShineWiFi-X communication is
normal.
LED State Indication
ShineWiFi-X not connected well
ALL three LED off
with inverter USB port
ShineWiFi-X and inverter
Only Red LED flashes
communication is OK
ShineWiFi-X, inverter and router
Only Green LED flashes
communication is OK
ShineWiFi-X, inverter, router and
Only Blue LED flashes
ShineSer ver communication is OK
Fill out the required information, then click Next
4. "
you to the "Add datalogger" page.
.If the pop up a message says "Failed", please refer to Appendix A of the troubleshooting guide
7
to solve the problem. After that, login to your account and click the "+" sign on the right top side
of the page, and select"Datalogger list"in the appearing dialog window. Push on the datalogger's
serial number for 3 sec, until a small dialog window appears,select "Configure datalogger". It
will move to the "Set ShineWifi-X"page,enter the home routers name and password, then click,
"Set" the connection configuration process will begin.
Reset ShineWiFi to Factory Settings
Step4.
When you have changed your home router password, or changed to
you need to reset ShineWiFi-X to factory settings and
KEY button for 6 sec, until all three LEDs long light
ShinePhone account, click the "+"on right top of this page,
datalogger serial number to reconfigure.
Appendix A: ShineWiFi-X KEY Button Description
Operation
When ShineWiFi-X is powered on, ShineWiFi-X will enter to AP
remove the rubber plug, and press the mode.（AP mode is a debug
KEY button. (ShineWiFi LED will mode, only allowed for
change from flash to always ON)
When ShineWiFi-X in AP mode, press
The KEY button of ShineWiFi-X
(ShineWiFi-X LED will change from
always ON to flash)
Long press the KEY button for
Reset ShineWiFi-X to
More than 6 sec (ShineWiFi-X
All LEDs always ON)
Electrical connection
Step1.
Rotate the USB cover of the photovoltaic device counterclockwise
1.
Rotate the datalogger locker on the upper, make sure the triangle is on the front side and in the middle.
2.
connect the datalogger to the inverter USB port, make sure the triangle is on the front side, press the locker and rotate clockwise until it is tighten.
3.
Registration and adding device
Step3.
Scan the QR code below to download ShinePhone, also you
search ShinePhone in iOS or Google Play Store,
install it.
Note:1. Make sure you download the latest version
2. For further information please visit server.growatt.com
Android & iOS
【
Scan QR code or input the ShineWiFi-X barcode and checkcode,
it will guide
5.
",
then click "Register", it will move you to the "Set ShineWifi-X"
page.
.After successful configuration, it will move to the
8
plant" page, select the inverter in the device list to
the
Troubleshooting
a new router,
reconfigure it. Press the
LED State
up, then login to your
long press this
All three LEDs are dark
After configuration,
Only Green LED flashes
Description
After configuration,
Only Blue LED flashes
Red LED always ON
professional）
Green LED always ON
Quit AP mode
Blue LED always ON
Factor y settings
Turn the triangle up and center,
then turn the lock clockwise
Connect your mobile phone to the WiFi of your home
1.
of which the ShineWiFi-X module will be connected.
1) The router name should consist with English letters
can
numbers, it does not support special symbols.
download and
2) For safety reason, please use an encrypted wireless network
3) It does not support a public network that uses a secondary
authentication.
4) It does not support bridge network.
2. Open ShinePhone APP, click "Register" on login page.
】
Fill out the wifi network and password, then click"Configuration", after successful configuration, a note will pop up
6.
"Configured successfully", then it will move to the "my plant" page.
Note: There are 3 LEDs on ShineWiFi-X, only the blue LED flashing indicates the ShineWiFi-X module is successfully
connected to the router and Growatt Shine Server.
"my
check
inverter update information.
Indicate
ShineWifi-X can not find inverter via USB port
ShineWiFi-X already connected to the home
router, but not connected
To Growatt ShineSer ver
ShineWiFi-X communication OK with inverter,
home router, and Growatt ShineSer ver
ShineWiFi-X module error
ShineWiFi-X can't connect to the home router
ShineWiFi-X module is in AP mode
router
Select country and city, then click "Next" enter next page.
3.
Note: If you select a wrong country and city, the system
and
time maybe wrong.
9.If you want to add/edit/delete/configure a datalogger, click the "+" sign on the right top side
"my plant" page. There are 4 options in the dialog window when push on the datalogger's
number, click the one you need.
1)" Add datalogger" is for adding a new ShineWiFi-X module to this account.
2) Edit datalogger" is used to assign an alias name for your ShineWiFi-X module. "
3) Delete datalogger" is used to remove the ShineWiFi-X module from this account. "
4 Configure datalogger" is used for configuring the connection of the ShineWiFi-X module to )"
router.
Troubleshooting
1.Tr y to reconnect ShineWifi-X to the inverter USB port
（1）Check if home router is connected to the internet
（2）Check if the router firewall allows to select port 5279 and 5280
Normal working state
Need to replace with a new ShineWiFi-X
（1）Check router information
a) Router name should consist of English letters and numbers, it does not
support special symbols
b) For safety reason, please use encr ypted wireless network
c) It does not support public network that use secondar y authentication
（ 2）Check if you filled in the correct name and password of the home router
when configuring it
Debug mode, short press the KEY button to quit
of the
serial
the