Advertisement
Quick Links
Order# XXXXX - MOD-1361 - iPad Kiosk
Item
Qty.
Description
1/1a
1/1
32.075" TSP49 Curved SEG Extrusion
1b
1
16.34" TSP49 Curved SEG Extrusion
2/2a
1/1
32.075" TSP49 Curved SEG Extrusion
2b
1
16.34" TSP49 Curved SEG Extrusion
3
1
20" TSP49 Horizontal SEG Extrusion
4
1
20" TSP49 Horizontal SEG Extrusion
5
1
20" TSP49 Horizontal SEG Extrusion
6
1
20" TSP49 Horizontal SEG Extrusion
7
1
16.4" Z45 Horizontal Extrusion
Steps:
1) Connect [1] to [1a] and [2] to [2a].
2) Connect [1/1a] and [2/2a] with [3].
3) Slide [7] into groove.
4) Connect [1/1a] and [2/2a] with [4] and assembled lightbox.
5) Attach assembled frame to base with bolts.
6) Attach front SEG graphics.
7) Position part [7] and lock in place.
8) Attach iPad mount see detail.
-- Continued page 2 --
Graphic: To Ensure Proper Fit
Corner A
Corner B
Corner D
Corner C
It is important to first insert
Step 1
Step 2
graphic into each alternate
Insert corner A. Turn edge of
Repeat Step 1 for opposite
corner then to the sides of
graphic so silicon welt is
corner C, then insert corner
the frame. If this is not done,
perpendicular to face of
B, followed by corner D, to
graphic will not fit into the
graphic. Insert narrow side
complete the installation of
frame correctly.
of welt with fabric to outside
the corners.
into the channel. Repeat for
other side of this corner.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work
toward
the
center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
w w w . c l a s s i c e x h i b i t s . c o m
- Assembly
1b
TSV1
Lock
1a
1
Graphic Removal
TSV1
Lock
To remove the graphic from
the frame, locate the fabric
pull tab. Gently pull up on the
tab to remove the fabric.
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
6
2b
5
TSV1
Lock
4
7
2a
2
Bolt
3
TSV1
Lock
LED Light
strips
around
perimeter
*
Mount Attachment
Z45
Do not remove
bolts from V20's
Apply SEG graphic and position extrusion [7]
Base
by loosening set screws, sliding into place, and
tightening set screws. S10 extrusion should
poke through hole in graphic. Loosen bolts on
iPad mount (Do Not Remove) and slide V20's
into S10 groove. tighten bolts to secure.
866.652.2100
TSV1 Lock Detail
Lock
TSP49
Tighten setscrew
to secure
extrusions
S10
7
V20's
*
© 2014
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Classic Exhibits SEGUE DESIGNS MOD-1361
Summary of Contents for Classic Exhibits SEGUE DESIGNS MOD-1361
- Page 1 Order# XXXXX - MOD-1361 - iPad Kiosk - Assembly 866.652.2100 Item Qty. Description 1/1a 32.075” TSP49 Curved SEG Extrusion 16.34” TSP49 Curved SEG Extrusion 2/2a 32.075” TSP49 Curved SEG Extrusion 16.34” TSP49 Curved SEG Extrusion 20” TSP49 Horizontal SEG Extrusion LED Light TSV1 Lock Detail 20”...
- Page 2 Order# XXXXX - MOD-1361 - iPad Kiosk - Assembly (Cont’d) 866.652.2100 Clamshell Lock Attachment Nuts Wire Management Attachment Lock Steps: 1) Run cords through plastic conduit. 2) Attach conduit where indicated by pinching the opening and inserting LED Light iPad Mounting Plate into the groove.
- Page 3 Order# XXXXX - MOD-1361 - iPad Kiosk - General Information 866.652.2100 Using Your Setup Instructions The Visionary Designs Setup Instructions are created specifically for your Detail A configuration. They are laid out sequentially, including an exploded view of the entire display, and then a logical series of detailed steps to assemble the main structure and components.
- Page 4 Order# XXXXX - MOD-1361 - iPad Kiosk - Packing Instructions 866.652.2100 Top View of Each Level Partly Assembled Frame Lightbox Top Graphics Base Setup Hardware Level 1 Level 2 WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING ©...
Need help?
Do you have a question about the SEGUE DESIGNS MOD-1361 and is the answer not in the manual?
Questions and answers