Advertisement
Pre-Installed Accessories
Other Accessories
Power/Clean Button
Dock/Spot Clean Button
Status Indicator
Reset Button
Tidy up items such as power cords, cloths, slippers, and toys to improve the efficiency of the robot.
Open the door of the room to be cleaned, and put the furniture in its proper place to make more space.
Before cleaning, place a physical barrier at the edge of the stairs and sofa to ensure safe and smooth operation of the robot.
To prevent the robot from not recognizing the area that needs to be cleaned, do not stand in the front of the robot, threshold, hallway, or narrow places.
Note: When operating the robot for the first time, follow it around while cleaning to remove any potential obstacles in time.
This product works with the Dreamehome app, which can be used to control your device.
Note: If your robot cannot connect to the app successfully, reset the Wi-Fi and add the device again.
After configuring the network for the first time, follow the instructions on the app to quickly create a map, and the robot will start mapping without cleaning. The mapping process will be completed when the robot returns to the dock, and the map will be saved automatically.
Press and hold the button for 3 seconds to turn on the robot. The power indicator should be illuminated. Place the robot onto the charging dock, the robot should turn on automatically and begin charging. To turn off the robot, move the robot away from the dock and press and hold the
button for 3 seconds.
Press the button briefly to start cleaning after the robot is turned on. Then, the robot will accurately map out a route, methodically clean along the edges and walls, then finish by cleaning each room in an S-shaped pattern to ensure a thorough job.
DreameBot D10s has four cleaning modes: Quiet, Standard, Strong, and Turbo. The default mode is Standard. You can specify the cleaning mode in the app.
When the robot is running, press any button to pause it. If the robot is paused for more than 10 minutes, it automatically enters sleep mode. All indicators on the robot will turn off. Press any button on the robot, or use the app to wake up the robot.
Note:
When the robot is paused or in Standby Mode, press and hold the button for 3 seconds to start Spot Clean Mode. In this mode, it will clean a square-shaped area of 1.5×1.5 meters directly around the robot. When the spot cleaning is done, the robot will automatically return to its original location and stop working.
Note: Activating Spot Clean Mode will end the current cleaning task of the robot.
When the robot is set to the Do Not Disturb (DND) mode, the robot will be prevented from resuming cleaning and the power indicator goes out. The DND mode is disabled by default at the factory. You can use the app to enable the DND mode or modify the DND period. The DND period is 22:00-8:00 by default.
Note:
You can schedule cleaning time in the Dreamehome app. The robot will automatically start cleaning at the designated time and then return to the charging dock to recharge when the cleaning is done.
Follow the instructions on the app interface to use more functions. The version of the app might have been updated; please follow the instructions based on the current app version.
It is recommended that all floors are vacuumed at least three times before the first mopping session to achieve a better cleaning effect.
To keep the robot in good condition, it is recommended to refer to the following table for routine maintenance.
Part | Maintenance Frequency | Replacement Period |
Mop pad | After each use | Every 3 to 6 months |
Main brush | Once every 2 weeks | Every 6 to 12 months |
Dust bin filter | Every 3 to 6 months | |
Side brush | ||
Charging dock's signaling area | Once every month | / |
Charging contacts | ||
Universal wheel | ||
Laser Distance Sensor (LDS) | ||
Cliff sensors | ||
Water tank | Clean it as needed | / |
Dust bin |
Note: The replacement frequency will depend on your usage of the robot. If an exception occurs due to special circumstances, the parts should be replaced.
Pull out the side brush and use the included cleaning tool to remove any hair tangled in the brush.
Note: Wet cloths can damage sensitive elements within the robot and charging dock. Please use dry rags for cleaning.
If the robot stops responding or cannot be turned off, press and hold down the button for 10 seconds to forcefully turn it off. Then press and hold the button
for 3 seconds to turn the robot on.
The robot contains a high-performance lithium-ion battery pack. Please ensure that it remains well-charged for daily use to maintain optimal battery performance. If the robot is not used for an extended period of time, turn it off and put it away. To prevent damage from over-discharging, the robot should be recharged at least once every three months.
The following table lists possible causes and solutions in terms of different light status. For more support, please refer to the section "Troubleshooting" in this manual.
Light Status | Possible Cause | Solution |
Off | No power supply | Check and ensure that the power supply from the charging dock is normal. |
The robot in the DND period The robot with full charge in sleep mode | / | |
White | The robot not on the charging dock | / |
Breathing White | The robot being charged | / |
Blinking Orange | Error | Check whether the dust bin of robot is installed. For other errors, contact qualified technicians or after-sales service. |
Problem | Solution |
Robot does not turn on | The battery level is low. Recharge the robot on the charging dock, then try again. |
Robot does not recharge | The charging dock is not receiving power. Please confirm that both ends of the power cord are plugged in correctly. Poor contact. Clean charging contacts of the charging dock and robot. |
Robot does not return to charging dock | There are too many obstructions around the charging dock. Place the charging dock in a more open area. Please clean the dock's signaling area. |
Robot is malfunctioning | Turn off the robot and then reactivate it. |
Robot is making a strange noise | A foreign object may be caught in the main brush, side brush, or one of the main wheels. Stop the robot and remove any debris. |
Robot no longer cleans efficiently or leaves dust behind | The dust bin is full. Please clean it. The filter is blocked. Please clean it. A foreign object is caught in the main brush. Please clean it. |
Robot cannot connect to Wi-Fi | There is something wrong with the Wi-Fi connection. Reset the Wi-Fi and download the latest version of the Dreamehome app, then try reconnecting. Location permission is not open. Please ensure the location permission on the Dreamehome app is enabled. Wi-Fi signal is weak. Make sure the robot is in an area with good Wi-Fi coverage. 5GHz Wi-Fi is not supported. Please ensure your robot connects to 2.4GHz Wi-Fi. The username or password of Wi-Fi is incorrect. Please enter the correct username and password. |
Robot does not perform scheduled cleaning | The robot has low battery. Scheduled cleaning will not start unless the robot has at least 15% battery left. |
Does leaving the robot on the charging dock consume power if it is already fully charged? | Leaving the robot on the charging dock after it's fully charged consumes very little electricity and helps maintain optimal battery performance. |
No water comes out of the mopping module, or only a little bit comes out | Check whether there is water inside the water tank. Clean the mop if it becomes dirty. Make sure the mop pad is installed correctly according to the User Manual. Clean the air hole on the top of the water tank. |
Robot doesn't resume cleaning after charging | Make sure the robot is not set to Do Not Disturb mode (DND), which will prevent it from resuming cleaning. The robot does not resume cleaning when it is manually recharged or placed onto the charging dock. |
Robot doesn't return to charging dock after being moved | Moving the robot may cause it to re-position itself or re-map its surroundings. If the robot is too far from the charging dock, it might not be able to automatically return on its own, in which case you need to manually place the robot onto the charging dock. |
For additional services, please contact us via aftersales@dreame.tech
Website: https://global.dreametech.com
Model | RLS3L |
Charging Time | Approx. 6 hours |
Rated Voltage | 14.4 V ![]() |
Rated Power | 46 W |
Operation Frequency | 2400-2483.5 MHz |
Maximum Output Power |
Model | RCS0 |
Rated Input | 100-240 V ~ 50/60 Hz 0.5 A |
Rated Output | 19.8 V ![]() |
Under normal use of condition, this equipment should be kept a separation distance of at least 20cm between the antenna and the body of the user.
To avoid electric shock, fire or injury caused by improper use of the appliance, please read the user manual carefully before using the appliance and keep it for future reference.
The built-in lithium-ion battery contains substances that are hazardous to the environment. Before disposing of the battery, make sure the battery is removed by qualified technicians and discarded at an appropriate recycling facility.
Before removing the battery, disconnect the power and run out the battery as much as possible.
Unneeded batteries should be discarded at an appropriate recycling facility.
Do not expose to high temperature environment to avoid risks of explosion.
Under abusive conditions, liquid may be ejected from the battery. If contact occurs, flush with water and seek medical help.
Removal Guide:
For more support, contact us via aftersales@dreame.tech
Website: https://global.dreametech.com
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download Dreame DreameBot D10s - Robot Vacuum and Mop Manual
Advertisement
Need help?
Do you have a question about the DreameBot D10s and is the answer not in the manual?
Questions and answers