Related Manuals for Pentair HYDROMATIC HPS3SC
Summary of Contents for Pentair HYDROMATIC HPS3SC
- Page 1 SUBMERSIBLE SOLIDS HANDLING PUMP HPS3SC(X), HPS4HC(X), HPS6MC(X) INSTALLATION & OPERATION MANUAL pentair.com ©2022 Pentair. All Rights Reserved.
-
Page 2: Table Of Contents
TABLE OF CONTENTS SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SPECIFICATIONS . -
Page 3: Safety Instructions
SAFETY INFORMATION SAFETY SYMBOLS CUTTING RISK. Risk of serious cutting or amputation exists. Use caution as liner plate is extremely This is the safety alert symbol. When you see this symbol on sharp. Always keep fingers and hands away from cutting your pump or in this manual, look for one of the following signal profiles. - Page 4 GENERAL INFORMATION This manual contains important safety information regarding HEAT SENSORS the use of this product. This product should only be installed All motors in this family have heat sensors on or embedded in the and serviced by a qualified professional. Carefully read and motor winding to detect excessive heat.
-
Page 5: Installation
INSTALLATION MAKING ELECTRICAL CONNECTIONS TO RE-WIRE THE PUMP FROM 230V TO 460V 3 PHASE Only a 230V pump from the factory is considered dual voltage, a ElECTROCUTION HAZARD: Must be cord label clearly states the factory wound voltage. installed by a qualified professional. Disconnect all electrical power before installation or servicing the pump. -
Page 6: Operation / Maintenance
OPERATIONS & MAINTENANCE PUMP MAINTENANCE RISK OF FIRE OR EXPLOSION. Do not smoke or use open flames in or around this system. Only the FM listed As the motors are oil filled, no lubrication or other maintenance is products are to be used in a hazardous location applications per required. - Page 7 CONFIDENTIAL contains trade secrets and [XXX] DIMENSIONS IN mm materials, compounds and other similar criteria are to be other proprietary information of Pentair CRITICAL DIMENSIONS THAT NEED Water. Duplication, disclosure or use are strictly adhered to. No modifications allowed without TO BE INSPECTED.
-
Page 8: Troubleshooting
Check in sump to be sure control is free. Selector switch may be in the Hand position. IF YOU HAVE ANY QUESTIONS REGARDING THE INSTALLATION, OPERATION, MAINTENANCE OR TROUBLESHOOTING OF THE PUMP, PLEASE CALL PENTAIR AT 855-274-8947. E-03-600 (07-15-22) - Page 9 PAGE INTENTIONALLY LEFT BLANK E-03-600 (07-15-22)
-
Page 10: Parts List
PARTS LIST HPS3SC(X), HPS4HC(X), HPS6MC(X) For use with product built with Premium Efficient motor. 4HC / 6MC E-03-600 (07-15-22) - Page 11 PARTS LIST ITEM PART DESCRIPTION PART # 4HC / 6MC CORD CAP 10-4 35' 152880315 CORD CAP 8-4 35' 152880325 CORD CAP 6-4 35' 152880335 STATOR SEE MOTOR PARTS GROUP ROTOR/SHAFT SEE MOTOR PARTS GROUP STATOR BOLT SHCS SEE MOTOR PARTS GROUP STATOR SPACER 007362141 153620017...
- Page 12 PARTS LIST HYDRAULIC ENDS B2 F26 B14 F26 B2 F26 B9 F26 B2 F26 B9 F26 TYPICAL: GAP BETWEEN LINER(B17) AND IMPELLER(1) TO BE SET AT .008-.015" FROM FACTORY ITEM DESCRIPTION KEY 3/8 X 1/4 SHAFT TO IMP ** / ++ 083460011 083460011 083460011...
- Page 13 PARTS LIST MOTOR PARTS 15 HP 15/20/23 HP 15/20/23 HP ITEM 2-POLE 3450RPM 208/3/60 230/460/3/60 575/3/60 STATOR 27889D003 27889D003 27889D603 ROTOR/SHAFT ASSEMBLY 27887D015 27887D015 27887D015 BOLT-STATOR (4) 001780051 001780051 001780051 SPACER 007362141 007362141 007362141 OIL-TRANSFORMER (1 .69) 153620017 153620017 153620017 10/15/20 HP 10/15/20/23 HP 10/15/20/23 HP...
- Page 14 PARTS LIST IMPELLER PARTS LIST - HPS4HC (X) - 1750 RPM DESCRIPTION PART # VOLTAGE/PH CORD TRIM IMPELLER HPS4HCP010403 528620117 208/3 8 .75 154471222 HPS4HCP010423 528620127 230/460/3 8 .75 154471222 HPS4HCP010443 528620137 460/3 10-4 8 .75 154471222 HPS4HCP010453 528620147 575/3 10-4 8 .75 154471222...
- Page 15 PARTS LIST IMPELLER PARTS LIST - HPS6MC(X) - 1750 RPM DESCRIPTION PART # VOLTAGE/PH CORD TRIM IMPELLER HPS6MCP010403 528610117 208/3 8 .13 154421152 HPS6MCP010423 528610127 230/460/3 8 .13 154421152 HPS6MCP010443 528610137 460/3 10-4 8 .13 154421152 HPS6MCP010453 528610147 575/3 10-4 8 .13 154421152 HPS6MCXP010403...
-
Page 16: Wiring Diagrams
WIRING DIAGRAMS E-03-600 (07-15-22) - Page 17 WIRING DIAGRAMS E-03-600 (07-15-22)
-
Page 18: Warranty
Pentair Hydromatic will cover only the lower seal and labor thereof for all dual seal pumps. under no circumstance will Pentair Hydromatic be responsible for the cost of field labor, travel expenses, rented equipment, removal/reinstallation costs or freight expenses to and from the factory or an authorized Pentair Hydromatic service facility. - Page 19 Fx: 888.606.5484 All indicated Pentair trademarks and logos are property of Pentair . Third party registered and unregistered trademarks and logos are the property of their respective owners . Because we are continuously improving our products and services, Pentair reserves the right to change specifications without prior notice. Pentair is an equal opportunity employer.