Related Manuals for Pentair HYDROMATIC HPS4HC
Summary of Contents for Pentair HYDROMATIC HPS4HC
- Page 1 SUBMERSIBLE SOLIDS HANDLING PUMP HPS4HC(X) , HPS6MC(X) INSTALLATION & OPERATION MANUAL pentair.com/hydromatic ©2023 Pentair. All Rights Reserved.
-
Page 2: Table Of Contents
TABLE OF CONTENTS SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 GENERAL INFORMATION . -
Page 3: Safety Information
SAFETY INFORMATION SAFETY SYMBOLS CUTTING RISK. Risk of serious cutting or amputation exists. Use caution as liner plate is extremely This is the safety alert symbol. When you see this symbol sharp. Always keep fingers and hands away from cutting on your pump or in this manual, look for one of the following profiles. -
Page 4: General Information
GENERAL INFORMATION This manual contains important safety information regarding HEAT SENSORS the use of this product. This product should only be installed All motors in this family have heat sensors on or embedded in the and serviced by a qualified professional. Carefully read and motor winding to detect excessive heat. -
Page 5: Installation
INSTALLATION MAKING ELECTRICAL CONNECTIONS TO RE-WIRE THE PUMP FROM 230V TO 460V 3 PHASE Only a 230V pump from the factory is considered dual voltage, ElECTROCUTION HAZARD: Must be a cord label clearly states the factory wound voltage. installed by a qualified professional. Disconnect all electrical power before installation or servicing the pump. -
Page 6: Operation / Maintenance
OPERATIONS & MAINTENANCE PUMP MAINTENANCE RISK OF FIRE OR EXPLOSION. Do not smoke or use open flames in or around this system. Only the FM listed As the motors are oil filled, no lubrication or other maintenance products are to be used in a hazardous location applications per is required. - Page 7 CONFIDENTIAL contains trade secrets and [XXX] DIMENSIONS IN mm materials, compounds and other similar criteria are to be other proprietary information of Pentair CRITICAL DIMENSIONS THAT NEED Water. Duplication, disclosure or use are strictly adhered to. No modifications allowed without TO BE INSPECTED.
-
Page 8: Troubleshooting
Lower float control may be hung-up in the closed position. Check in sump to be sure control is free. Selector switch may be in the Hand position. IF YOU HAVE ANY QUESTIONS REGARDING THE INSTALLATION, OPERATION, MAINTENANCE OR TROUBLESHOOTING OF THE PUMP, PLEASE CALL PENTAIR AT 855-274-8947. E-03-600 (11-13-23) - Page 9 NOTES PAGE E-03-600 (11-13-23)
-
Page 10: Parts List
PARTS LIST HPS4HC(X), HPS6MC(X) For use with product built with Premium Efficient motor. 4HC / 6MC E-03-600 (11-13-23) - Page 11 PARTS LIST ITEM PART DESCRIPTION PART # 4HC / 6MC CORD CAP 10-4 35' 152880315 CORD CAP 8-4 35' 152880325 CORD CAP 6-4 35' 152880335 STATOR SEE MOTOR PARTS GROUP ROTOR/SHAFT SEE MOTOR PARTS GROUP STATOR BOLT SHCS SEE MOTOR PARTS GROUP STATOR SPACER 007362141 153620017...
- Page 12 PARTS LIST HYDRAULIC ENDS B2 F26 B14 F26 B2 F26 B2 F26 B14 F26 B14 F26 B2 F26 B9 F26 B2 F26 B2 F26 B2 F26 B9 F26 B9 F26 B9 F26 TYPICAL: GAP BETWEEN LINER(B17) AND IMPELLER(1) TO BE SET AT .008-.015" FROM FACTORY B2 F26 B2 F26 B9 F26...
- Page 13 PARTS LIST MOTOR PARTS 10/15/20 HP 10/15/20/23 HP 10/15/20/23 HP ITEM 4-POLE 1750RPM 208/3/60 230/460/3/60 575/3/60 STATOR 27886D003 27886D003 27886D603 ROTOR/SHAFT ASSEMBLY 27886D015 27886D015 27886D015 BOLT-STATOR (4) 06106A070 06106A070 06106A070 SPACER OIL-TRANSFORMER (1 .63) 153620017 153620017 153620017 E-03-600 (11-13-23)
- Page 14 PARTS LIST IMPELLER PARTS LIST - HPS4HC (X) - 1750 RPM DESCRIPTION PART # VOLTAGE/PH CORD TRIM IMPELLER HPS4HCP010403 528620117 208/3 8 .75 154476222 HPS4HCP010423 528620127 230/460/3 8 .75 154476222 HPS4HCP010443 528620137 460/3 10-4 8 .75 154476222 HPS4HCP010453 528620147 575/3 10-4 8 .75 154476222...
- Page 15 PARTS LIST IMPELLER PARTS LIST - HPS6MC(X) - 1750 RPM DESCRIPTION PART # VOLTAGE/PH CORD TRIM IMPELLER HPS6MCP010403 528610117 208/3 8 .13 154426152 HPS6MCP010423 528610127 230/460/3 8 .13 154426152 HPS6MCP010443 528610137 460/3 10-4 8 .13 154426152 HPS6MCP010453 528610147 575/3 10-4 8 .13 154426152 HPS6MCXP010403...
-
Page 16: Wiring Diagrams
WIRING DIAGRAMS E-03-600 (11-13-23) - Page 17 WIRING DIAGRAMS E-03-600 (11-13-23)
-
Page 18: Warranty
Pentair Hydromatic will cover only the lower seal and labor thereof for all dual seal pumps. under no circumstance will Pentair Hydromatic be responsible for the cost of field labor, travel expenses, rented equipment, removal/reinstallation costs or freight expenses to and from the factory or an authorized Pentair Hydromatic service facility. - Page 19 NOTES PAGE E-03-600 (11-13-23)
- Page 20 Fx: 888.606.5484 All indicated Pentair trademarks and logos are property of Pentair . Third party registered and unregistered trademarks and logos are the property of their respective owners . Loctite® is a registered trademark of Henkel AG & Company KGaA .