Related Manuals for Pentair HYDROMATIC HPS4SD
Summary of Contents for Pentair HYDROMATIC HPS4SD
- Page 1 SUBMERSIBLE SOLIDS HANDLING PUMP HPS4SD(X) HPS4HD (X) HPS6MD(X) INSTALLATION & OPERATION MANUAL pentair.com ©2022 Pentair. All Rights Reserved.
-
Page 2: Table Of Contents
TABLE OF CONTENTS SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 GENERAL INFORMATION . -
Page 3: Safety Instructions
SAFETY INFORMATION CUTTING RISK. Risk of serious cutting or SAFETY SYMBOLS amputation exists. Use caution as liner plate is extremely This is the safety alert symbol. When you see this symbol on sharp. Always keep fingers and hands away from cutting your pump or in this manual, look for one of the following signal profiles. -
Page 4: General Information
GENERAL INFORMATION This manual contains important safety information regarding HEAT SENSORS the use of this product. This product should only be installed All motors in this family have heat sensors on or embedded in the and serviced by a qualified professional. Carefully read and motor winding to detect excessive heat. -
Page 5: Installation
INSTALLATION AKING ELECTRICAL CONNECTIONS TO RE-WIRE THE PUMP FROM 230V TO 460V 3 PHASE All electrical wiring must be in accordance with local codes, Only a 230V pump from the factory is considered dual voltage, a and only competent electricians should make the installations. cord label clearly states the factory wound voltage. -
Page 6: Operation / Maintenance
OPERATIONS & MAINTENANCE PUMP OPERATIONS STARTING SYSTEM PUMP MAINTENANCE Double check all wire connections. As the motors are oil filled, no lubrication or other maintenance is required. Turn pumps to Off position on H-O-A switches. Turn on breakers. If the heat sensor and seal failure are hooked up properly, no attention is necessary as long as the seal failure indicator light Connect amprobe to pump power cord and turn pump on. -
Page 7: Troubleshooting
CONFIDENTIAL contains trade secrets and ASHLAND, OH. USA materials, compounds and other similar criteria are to be other proprietary information of Pentair Water. Duplication, disclosure or use are strictly adhered to. No modifications allowed without forbidden without the written consent of engineering approval. - Page 8 TROUBLESHOOTING PUMP DOES NOT DELIVER PROPER CAPACITY PUMP TROUBLESHOOTING Discharge gate valve may be partially closed or partially Below is a list of common problems and the probable causes. clogged. PUMP WILL NOT START Check valve may be partially clogged. Raise level up and No power to the motor.
- Page 9 PAGE INTENTIONALLY LEFT BLANK E-03-601 (02-15-22)
-
Page 10: Parts List
PARTS LIST HPS4SD(X), HPS4HD(X), HPS6MD(X) For use with product built with Premium Efficient motor. E-03-601 (02-15-22) - Page 11 PARTS LIST ITEM PART DESCRIPTION PART # 4SD / 4HD / 6MD CORD CAP 10-4 35' 152880315 CORD CAP 8-4 35' 152880325 CORD CAP 6-4 35' 152880335 STATOR SEE MOTOR PARTS GROUP ROTOR/SHAFT ASSEMBLY SEE MOTOR PARTS GROUP SPACER SEE MOTOR PARTS GROUP 153620017 BOLT-STATOR 06106A027...
- Page 12 PARTS LIST HYDRAULIC ENDS PARTS LIST B7 F26 B11 F26 B3 F26 B11 F26 B3 F26 B11 F26 TYPICAL: GAP BETWEEN LINER(B15) AND IMPELLER(1) TO BE .008-.015" FROM FACTORY. ITEM DESCRIPTION PART # O-RING VOL COVER ** 05876A108 SCREW-HEX HEAD VOL COVER 002380301 SCREW-SOCKET HEAD CAP LINER BOLT 005560081...
- Page 13 PARTS LIST MOTOR PARTS LIST 25HP 25HP 30/40HP 30/40HP ITEM 2-POLE 3450 RPM 230/460/3/60 575/3/60 460/3/60 575/3/60 STATOR 27906D003 27906D603 27907D003 27907D603 ROTOR/SHAFT ASSEMBLY 27906D130 27906D130 27907D130 27907D130 153620017 (4 .8) 153620017 (4 .8) 153620017 (4 .25) 153620017 (4 .25) BOLT-STATOR 06106A027 (4)
- Page 14 PARTS LIST IMPELLER PARTS LIST - HPS4HD(X) 1750 RPM DESCRIPTION PART # VOLTAGE/PH CORD TRIM IMPELLER HPS4HDP025403 528650017 208/3 10 .75 154641142 HPS4HDP025423 528650027 230-460/3 10 .75 154641142 HPS4HDP025443 528650037 460/3 10 .75 154641142 HPS4HDP025453 528650047 575/3 10 .75 154641142 HPS4HDXP025403 528656017 208/3...
- Page 15 PAGE INTENTIONALLY LEFT BLANK E-03-601 (02-15-22)
-
Page 16: Wiring Diagrams
WIRING DIAGRAMS 3 PHASE Notes: 1. Level Switches Must be Rated a Minimum of 2 Amps at 120 Volts. 2. Torque all eld wiring terminals to 20 in. Lbs. 3. Field Wiring Must be 60˚C Copper Wire Minimum. = Items Not Supplied In Control Panel. 5. - Page 17 WIRING DIAGRAMS E-03-601 (02-15-22)
-
Page 18: Warranty
Fx: 888.606.5484 All indicated Pentair trademarks and logos are property of Pentair . Third party registered and unregistered trademarks and logos are the property of their respective owners . Because we are continuously improving our products and services, Pentair reserves the right to change specifications without prior notice . Pentair is an equal opportunity employer .